Luxul Xap-1010 User manual

luxul.com

Simply Connected

User Guide

XAP-1010

Luxul Xen™ Flush Mount

802.11b/g/n Wireless Access Point

Use the XAP-1010 to:

Provide an Unobtrusive Wireless Network that Eliminates

Unsightly Cables or Equipment

Deliver “Whole Home” or Ofﬁ ce 802.11n Wi-Fi Coverage With a

Single Access Point

Increase Mobile Client Device Network Sensitivity and

Performance

Simplify Installation While Minimizing Setup Time and Expense

Eliminate Client Device Roaming Issues

User Guide

LUXUL XEN FLUSH MOUNT

802.11b/g/n Wireless Access Point

Model Number: XAP-1010

FCC ID: W59XAP101020

IC: 8584A-XAP101020

USER GUIDE

No part of this publication may be modiﬁ ed or adapted in any way, for any

purposes without permission in writing from Luxul. The material in this manual

is subject to change without notice. Luxul reserves the right to make changes to

any product to improve reliability, function, or design. No license is granted, either

expressly or by implication or otherwise under any Luxul intellectual property rights.

An implied license only exists for equipment, circuits and subsystems contained in

this or any Luxul product.

This product is covered by one or more U.S. and foreign patents Patents: 7,379,717,

6,606,075, 6,373,448, other patents pending

DOCUMENT CONVENTIONS

The following graphical alerts are used in this document to indicate notable situations:

NOTE: Tips, hints, or special requirements that you should take note of.

CAUTION: Care is required. Disregarding a caution can result in data

loss or equipment malfunction.

WARNING!: Indicates a condition or procedure that could result in

personal injury or equipment damage.

FCC COMPLIANCE

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

User Guide

CONTENTS

1 INTRODUCTION 4

1.1 Warnings 5

1.2 Site Preparation 5

2 XAP-1010 SPECIFICATIONS 5

3 GETTING STARTED 7

3.1 System Requirements 7

3.2 Package Contents 7

3.3 Safety Information 7

4 HARDWARE FEATURES AND INSTALLATION 8

4.1 Front View 8

4.2 Rear View 10

4.3 Environmental Requirements 11

4.4 Hardware Installation 12

5 CONFIGURATION 16

5.1 Login 16

5.2 Quick Setup 16

5.3 Wireless 20

5.4 Maintenance 23

5.5 QoS 25

5.6 Status 26

6 REGULATORY COMPLIANCE 27

6.1 Health and Safety Recommendations 27

6.2 RF Exposure Guidelines 28

6.3 Radio Frequency Interference Requirements—FCC 28

6.4 Radio Transmitters (Part 15) 29

6.5 Industry Canada (RSS-Gen Issue 2) 29

APPENDIX 1: TECHNICAL SUPPORT 29

User Guide

1 INTRODUCTION

Congratulations on your purchase of the Luxul Xen™ High Performance Flush Mount

802.11n Wireless Access Point (XAP-1010). The XAP-1010 is designed for discreet

use in residential and commercial Wi-Fi installations—delivering optimal network

performance, while blending unobtrusively with the décor when installed inside

a wall or ceiling. Powered by Luxul’s Xen3D™ Technology, the XAP-1010 enhances

data throughput and coverage by as much as 400% over traditional Wi-Fi gear,

providing for whole home or small ofﬁ ce coverage with a single access point. With

this high performance wireless access point, computers and wireless devices that

are compatible with 802.11b/g and/or 802.11n can sustain maximum data rates and

improved overall performance at signiﬁ cantly greater distances.

The XAP-1010 features Luxul’s XenSmart™ web based management interface.

XenSmart provides a powerful, yet simple method for setting up and optimizing

the wireless network. The XAP-1010 is also XenConnect™ enabled for optimal per-

formance and installation simplicity when deployed together with Luxul Routers,

Gigabit Switches, and other Luxul products.

XAP-1010 Features:

Implements Patented Xen3D™ Technology for Enhanced Throughput and Coverage

Highest FCC Approved Performance (Effective EIRP 36dBm) for Farther Reaching

Signal and Maximum Data Rates

18dB of Receive Gain Increases Client Device Network Sensitivity and Performance

Complies with 2.4 GHz IEEE 802.11n Standard. Backward Compatible with IEEE

802.11g/b

Supports WMM QoS Functionality to Prioritize Multimedia Trafﬁ c

Enhanced Multi-Level Security with WPA-PSK (TKIP, AES, TKIP & AES), WPA2-PSK

(AES), WPA-PSK/WPA2-PSK Personal (TKIP & AES) and 128-bit WEP

Supports up to 8 SSIDs with Individual Security Settings

Multiple SSIDs Support VLAN Tagging (1 VLAN per SSID)

Single Cable Installation with PoE (supports both IEEE 802.3af and Legacy)

Firmware Upgradeable

Easy 3 Step Setup through Web-based XenSmart™ User Interface

Install inside Wall or Ceiling

Paintable Cover Plate Unobtrusively Blends Into the Room Décor

User Guide

XenConnect™ Enabled for Maximum Compatibility and Performance with Other

Luxul Xen Products

1.1 Warnings

Read all installation instructions and site survey reports, and verify correct equip-

ment installation before connecting the XAP-1010 to its power source.

Remove jewelry and watches before installing this equipment.

Verify that the unit is grounded before connecting it to the power source.

Verify that any device connected to this unit is properly wired and grounded.

Connect all power cords to a properly wired and grounded electrical circuit.

Verify that the electrical circuits have appropriate overload protection.

Attach only approved power cords to the device.

Verify that the power connector and socket are accessible at all times during the

operation of the equipment.

Do not work with power circuits in dimly lit spaces.

Do not install this equipment or work with its power circuits during thunder-

storms or other weather conditions that could cause a power surge.

Verify there is adequate ventilation around the device, and that ambient tem-

peratures meet equipment operation speciﬁ cations.

Products outside the approved conﬁ gurations may be in violation of Part 15 of

the FCC Rules.

1.2 Site Preparation

Consult your site survey and network analysis reports to determine speciﬁ c

equipment placement, power drops, and so on.

Assign installation responsibility to the appropriate personnel.

Identify and document where all installed components are located.

Provide a sufﬁ cient number of power drops for your equipment.

Ensure adequate, dust-free ventilation to all installed equipment.

Identify and prepare Ethernet and console port connections.

Verify that cable lengths are within the maximum allowable distances for optimal

and certiﬁ ed signal transmission.

User Guide

2 XAP-1010 SPECIFICATIONS

Standards IEEE 802.11n

IEEE 802.11b/g

IEEE 802.3af

Hardware LAN Port: 1 RJ45 10/100 Mbps data and power input

 7dBi Circular Polarized Directional Antenna

LEDs: All LEDs are internal and not visible when cover

plate is in place (Power, WLAN active, LAN link/

activity, Bridge mode active).

RF Information Frequency Band: 2.401 – 2.473GHz

Operating Channels: 11

Available Transmit Power 2.401 – 2.473GHz (IEEE802.11g/n):

Up to 36dBm EIRP

30dBm @ 6~9Mbps / MCS0

29dBm @ 12~18Mbps / MCS1-2

27dBm @ 24~36Mbps / MCS3-4

26dBm @ 48~54Mbps / MCS5-7

2.401 – 2.473GHz (IEEE802.11b):

Up to 36dBm EIRP

30dBm @ 1~11Mbps

Available Receive Gain  2.401 – 2.473GHz (IEEE802.11g/n):

Up to 18dBm

2.401 – 2.473GHz (IEEE802.11b):

Up to 18dBm

Receive Sensitivity (Typical) 2.401 – 2.473GHz (IEEE802.11n): Up to -91dBm

2.401 – 2.473GHz (IEEE802.11g): Up to -92dBm

2.401 – 2.473GHz (IEEE802.11b): Up to -93dBm

Wireless Operation Modes Access Point

Point-to Point Wireless Bridge

Point-to-Multipoint Wireless Bridge

Management and Security XenSmart™ Remote Web-based Management

WEP (128 bit)

WPA-PSK (TKIP, AES, TKIP&AES)

WPA2-PSK (AES)

WPA-PSK/WPA2-PSK Auto (TKIP&AES)

Web Based Firmware Upgrade

QoS: Wireless Multi-Media (WMM) Extensions

Certiﬁ cations FCC Part 15, Class B

User Guide

Power Requirements Ethernet POE in: 48VDC/0.375A for IEEE 802.3af

Compliance

Power Consumption: 5W Nominal, 13W Max

Temperature Range Operating: 14°F to 132°F (-10°C to 50°C)

Storage: -40°F to 158°F (-40°C to 70°C)

Operating Humidity 5% to 95% (Non-condensing)

Mechanical Housing Dimensions: Fits within standard 2 gang

electrical box WxHxD: 3.7”(93.98mm) x 3.8”(96.52mm)

x 1.1”(27.94mm)

Cover Plate Dimensions WxHxD: 5.5”(139.7 mm) x

5.5”(139.7 mm) x .375”(9.525mm)

Weight Item: .7 lbs

With Packaging: 1.5 lbs

Warranty 1 year

Minimum System

Requirements

Devices Supporting 802.11b, 802.11g or 802.11n

Web Browser (Microsoft IE 7.0 and up, Mozilla Firefox

1.0 and up, Safari 1.0 and up, Google Chrome 5.0 and

up)

CAT5 Ethernet Cable

Internet Connection to View Documentation Online

3 GETTING STARTED

3.1 System Requirements

Devices Supporting 802.11b, 802.11g or 802.11n

Web Browser (Microsoft IE 7.0 and up, Mozilla Firefox 1.0 and up, Safari 1.0 and up,

Google Chrome 5.0 and up)

CAT5 Ethernet Cable

AC Power Socket (100 – 240 V, 50/60 Hz)

Internet Connection to View Documentation Online

3.2 Package Contents

XAP-1010 Wireless Access Point

Paintable Faceplate and Mounting Screws

2 Gang Remodel Electrical Box

POE Injector and Power Adapter

Quick Install Guide

User Guide

NOTE: If any of the listed items are missing or damaged, please contact

the reseller from whom you purchased for return/replacement.

3.3 Safety Information

To maintain the safety of users and property, follow these safety instructions:

The XAP-1010 wireless access point is designed for indoor use only. DO NOT

place this access point outdoors. If you require an outdoor access point, please

consider the Luxul XAP-1040.

DO NOT install this access point in or near hot or humid places, such as a kitchen

or bathroom. Take care to minimize exposure to excessive heat or moisture.

DO NOT pull any connected cable with force. When disconnecting cables, do so

by disconnecting ﬁ rst from the access point. When reconnecting, connect the AP

ﬁ rst and then the Power/data source.

When installing the access point, be sure it is ﬁ rmly secured within an appropri-

ately shielded electrical box to protect the unit from dust, insulation, and other

external elements. If not using the electrical box included with the unit, ALWAYS

use a properly shielded and UL listed electrical box for installation.

Accessories of this access point, such as mounting screws, the POE injector and

power supply may be dangerous to small children under 3 years of age. KEEP All

ACCESSORIES OUT OF THE REACH OF CHILDREN!

The access point may become hot when in use for extended time periods. This is

normal and is not a malfunction. DO NOT install this access point where it will

be exposed to paper, cloth or other ﬂ ammable materials. If not using the electri-

cal box included with the unit, ALWAYS use a properly shielded and UL listed

electrical box for installation.

The XAP-1010 contains no user-serviceable parts. If the access point is not work-

ing properly, contact your dealer and ask for help. DO NOT attempt to disas-

semble the access point.

4 HARDWARE FEATURES AND INSTALLATION

The XAP-1010 high powered access point is designed for optimal performance as

well as for simple and efﬁ cient installation and setup. It implements Luxul’s circular

polarized directional antenna technology and is packaged for installation within a

wall or ceiling. Because the signal generated by the XAP-1010 is directional in nature,

the unit should be placed in a location that allows the antenna face to be “pointed”

towards the desired coverage area. Typically this would be in a top ﬂ oor ceiling

pointed downwards in a multi-story installation; or for single level or two level

User Guide

layouts, on a wall pointed towards the desired coverage.

4.1 Front View

The front of the XAP-1010 consists of the antenna element and 4 LEDs. LEDs

indicate 1) Power, 2) WLAN Status 3) LAN Link/Activity, and 4) Bridge Mode.

NOTE: LEDs are only visible when the cover plate is removed

XAP-1010 Front View

Status Indicators:

The XAP-1010 has four LEDs, positioned vertically on the right side of the front of

the access point. When viewed from top to bottom, LEDs are as follows: 1) Bridge

Mode (Green); 2) WLAN Status (Blue); 3) LAN Link/Activity (Amber); and 4) Power

(Green).

User Guide

The following table describes the LED functionality:

Indicator Name Description

Bridge Mode On Bridge Mode is enabled

Off The AP is in default “Access Point” mode.

WLAN Status On The wireless radio is active and wireless

access is enabled an active connection to the

internet

Off The wireless radio is not active and wireless

access is disabled

LAN Link/Activity On There is an active Ethernet connection

Flashing Indicates Ethernet activity

Off There is no active Ethernet connection

Power On The power is on

Off No power, check power connections

At startup, the Green Power LED will stay on while the amber LAN Link light

ﬂ ashes. The blue LED will come on once the XAP-1010 radio is active.

4.2 Rear View

The rear of the XAP-1010 provides one RJ-45 connection that is used to deliver both

power and data to the access point. It also provides a reset button for restoring the

access point to factory default settings.

XAP-1010 Rear View

User Guide

1111

The Reset button is used to clear the current settings of the XAP-1010 and restore

factory default settings.

Reset

XAP-1010 Reset Button Location

To Restore the Default Settings: With the XAP-1010 powered on, press and hold

the Reset button for 10 seconds. When the Power LED comes on again, release the

reset button. The XAP-1010 will be set to factory defaults.

CAUTION: Pressing and holding the Reset button will remove any

custom conﬁ gurations done to the XAP-1010.

4.3 Environmental Requirements

 Ethernet cable at the electrical box installation location to provide Power and

Data to the XAP-1010.

A computer supporting TCP/IP and equipped with a Web browser. Supported

Web browser versions include Microsoft IE 7.0 and up, Safari 1.0 and up, Mozilla

Firefox 1.0 and up, and Google Chrome 5.0 and up. The Web browser is used to

conﬁ gure the XAP-1010.

The XAP-1010 uses 36-57VDC power. The POE injector power supply requires AC

100V ~ 240V, 50Hz ~ 60Hz.

Temperature of the operating environment: 32F~131F (0C~55C). Be sure to place

the access point away from heat generating devices.

Humidity of the operating environment: 5%-95% non-condensing. Do not place

the access point in an extremely dirty or damp location.

Keep the access point away from strong electromagnetic ﬁ elds (i.e. Air

Conditioner compressors, ﬂ uorescent light ballasts, CRT monitors/televisions,

etc.), and free from vibration, dust and direct sun light.

User Guide

4.4 Hardware Installation

4.4.1 Access Point Placement

This XAP-1010 implements Luxul’s Circular Polarized directional antenna technol-

ogy. For maximum efﬁ ciency, it should be aimed towards the area to which you

would like to provide coverage. With this in mind, the ideal placement option is

usually on an outside wall pointed into the coverage area; or in a multi-level instal-

lation, on the top ﬂ oor ceiling pointed downwards.

XAP-1010 Suggested Mounting Location

4.4.2 Mounting the Access Point within a Wall or Ceiling

The XAP-1010 is designed to be installed within a standard 2 gang electrical box. A

remodel box is included with this kit. If you choose to use your own electrical box,

be sure it is UL listed and provides sufﬁ cient shielding to minimize contamination

from dust, insulation and other external elements. Once the electrical box is in

place along with the appropriate Ethernet cable pulled inside the box, simply plug

the Ethernet cable into the RJ-45 connector and mount the access point directly to

the electrical box as shown in the diagram below:

User Guide

1313

XAP-1010 Assembly View

4.4.3 Connecting to the Power Source

The XAP-1010 is POE ready and supports Legacy (48v 1a), 802.3af, and 802.3at

POE injectors. A POE injector is included with the device. To apply power, simply

connect the opposite end of the Ethernet cable to which the access point is

already connected to the provided POE injector or other POE switch or injector. An

Ethernet cable length of up to 300 feet can be used. DO NOT yet apply power to

the POE injector or switch.

NOTE: Category-5, super Category-5 or Category-6 unshielded twisted

pair (CAT5/CAT5e/CAT6 UTP) cables can be used. For best

results, it is recommended that Category-6 shielded twisted pair

be used to ensure stable data transmission at highest data rates.

User Guide

4.4.4 Connecting to the Internet Source

The Luxul device is not a router and in most installations will be connected to a

Router or Switch in order to deliver Internet access. To do so, connect the POE

injector (or switch) to the desired Internet source using another Ethernet cable. Be

sure the source device is powered off.

Data

Source

Power

Source

Data

Power

Data/Pwr

Out

POE

Injector

The POE Injector Sends Power and Signal Over One Ethernet Cable

4.4.5 Applying Power

Once the Ethernet cables have been properly connected, connect the power sup-

ply to the POE injector and plug it in to a standard AC power outlet. Or, if plugging

into a POE switch, turn the switch (or appropriate port) on. The network source

device can also now be powered back on.

NOTE: If your Internet source (Router or Switch) is a POE enabled device

and connected via POE, it can be plugged directly into the access

point without the need to run a separate POE injector.

4.4.6 LED Visual Veriﬁ cation

With power applied, you can now verify that the XAP-1010 is connected and

functioning properly. Prior to placing the access point cover plate, perform a visual

inspection of the LEDs. The Green Power LED (bottom of the stack) should be on

while the amber LAN Link light ﬂ ashes, indicating activity. Once the XAP-1010 is

properly connected to the Internet source, the blue WLAN LED should also remain

on. The Green LED at the top of the stack will only be on if the access point is set

to function in bridge mode.

User Guide

1515

XAP-1010 LED Visual Veriﬁ ction

4.4.7 ATTACHING THE COVER PLATE

Once it has been determined that the access point is functioning properly, attach

the cover plate using the screws provided. Be sure not to over-tighten the screws.

Note that the cover plate is paintable.

NOTE: If painting the cover plate, be sure to use only latex based paints.

CAUTION: Paint or wall covering with any metal content placed over the

front of the XAP-1010 will effect the performance of the unit.

5 CONFIGURATION

5.1 Login

The XAP-1010 is not equipped with internal DHCP server. If connected to the Luxul

XBR-2300 Enterprise Dual-WAN Router, conﬁ guration will be automatic. Otherwise,

the IP address of the computer for login and conﬁ guration will need to be manually

conﬁ gured. The table below lists the default parameters of the XAP-1010.

Parameter Default Value

Default IP address 192.168.0.10

Default user name admin

Default password admin

User Guide

a. Be sure the XAP-1010 is properly installed and powered on

b. Open your Web Browser, and enter http://192.168.0.10.

The login window appears as shown below:

c. Enter the user name and password (default user name is ”admin” and default

password is “admin”), and then click OK to login to the Quick Setup window.

5.2 Quick Setup

Quick Setup: For most installations, it is expected that the Quick Setup page will

be sufﬁ cient to optimally conﬁ gure and deploy the XAP-1010 Wi-Fi network. The

Quick Setup page consists of the following:

DHCP Client: Enabled or Disabled. DHCP (Dynamic Host Conﬁ guration Protocol)

is used to automatically assign an IP Addresses to a device on the network. If

DHCP is enabled on the Access Point, it will no longer use the static address set

by Luxul at time of manufacturing and will request a dynamic IP Address from the

Router (sometimes referred to as the Gateway).

User Guide

1717

When DHCP is enabled on the Access Point, the new IP address will be needed

in order to access the XenSmart™ web management interface. The Router web

interface can be used to look up the IP address assigned to the Access Point. To

Enable DHCP, click on the drop down menu and select Enable. Select Apply and

then Reboot for the change to take effect.

NOTE: DHCP is set as Disabled by default and is the recommended

setting in order to ensure optimal communications with all Luxul

Xen devices on the network.

IP Address: An IP address is a numerical label assigned to each device on the

network. This ﬁ eld shows the IP address that is assigned to the XAP-1010. To

ensure plug and play capability with other Luxul networking products, the IP

Address is automatically defaulted to 192.168.0.10. If desired, the user can set

this to a different static IP Address. To change the IP address of the Access

Point, simply type in the desired IP address (the text ﬁ eld will be red if the

address is incomplete), click Apply and then Reboot for the changed to take

effect. When connecting to the Access Point through the XenSmart™ web

interface, the NEW IP Address must be used.

NOTE: Each device on the same network must have a unique IP address.

If the Access Point is assigned an IP address already in use, it

will result in an IP address conﬂ ict that will need to be resolved

manually. For optimal communications with all Luxul Xen devices

on the network, it is recommended that IP addresses not be

changed unless absolutely necessary.

 Subnet Mask: To ensure plug and play capability with other Luxul networking

products, the Subnet Mask is automatically defaulted to 255.255.255.0. If desired,

the user can set this to a different static Subnet Mask.

Default Gateway: A gateway is a router on the network that connects two or

more networks together. Typically the gateway (router) connects the local area

network (LAN) to the Internet. The Internet Service Provider (ISP) often provides

a physical device (usually a DSL modem or cable modem) that connects to the

gateway with an Ethernet cable, thus completing the link to the Internet. For

optimal connectivity and network functionality, this device could also be the

Luxul Xen XBR-2300 Router.

The Default Gateway ﬁ eld is the IP address for this routing device. The default

conﬁ guration is left blank or empty, allowing the Access Point to automatically ﬁ nd

the necessary route to the Internet. It is recommended to leave this ﬁ eld blank.

User Guide

 Network Name (SSID): Sets the name of the Wireless Network. Default name

is LuxulXen. It is recommended to change the SSID from the default name. The

SSID is case sensitive and can contain:

2 – 32 alphanumeric characters

Spaces

Special characters (i.e. @#$%&*)

To change the SSID of the wireless network, simply type the desired name, click

Save, and then Reboot for the change to take effect.

 Security Mode: Sets the wireless security encryption mode. It is HIGHLY

recommended to change the Security Mode and use the highest security level

supported by the client devices in the network. In most wireless networks, WPA/

WPA2 Personal is an excellent option that will support the largest cross section

of client devices. Security options include:

Open (default - no security)

WEP (128 bit shared key)

WPA Personal

WPA2 Personal

WPA/WPA2 Personal

To change the Security Mode, click the drop down menu and select the desired

mode. The available options for the selected mode will then appear. AFTER all

options are complete, click Save, and then Reboot for the change to take effect.

 Encryption: This ﬁ eld sets the type of encryption to be used by the Security

Mode. The encryption options are dependent upon the Security Mode selected

and this ﬁ eld only shows while in WPA mode. For WEP and WPA2, and WPA/

WPA2 Personal, encryption is automatically set to 128 bits, AES, and TKIP &

AES respectively. For WPA, there are three options: AES, TKIP, and TKIP & AES.

When set to WPA, it is recommended that TKIP & AES be used. To change the

Encryption, click the drop down menu and select the desired encryption type.

Once all options are selected, click Save and then Reboot for the change to take

effect.

 WEP Key: This ﬁ eld only shows while in WEP mode and sets the WEP key to be

used in the network. WEP 128 bit keys require 26 characters. Allowed characters

are numbers 0-9 and letters a-f. There are WEP key generators online that can

automatically create a key. To change the WEP Key, simply enter the 26 character

key then click Save and then Reboot for the change to take effect.

 WPA Passphrase: This sets the passphrase used by client devices to connect to

the wireless network when using WPA Security Mode. For WPA the passphrase:

User Guide

1919

Must be a minimum of 8, maximum of 63 characters

Can contain spaces or special characters (i.e. @#$%&*)

To change the WPA Passphrase, simply type in the desired passphrase, click Save,

then Reboot for the change to take effect.

NOTE: It is recommended to use a strong password containing:

More than the minimum number of characters

One or more capital letters

Numbers and/or special characters

 Administrator Login: Sets the password for Administrator access to the

XenSmart™ web management interface. When connecting to the Access Point

through the XenSmart™ web interface, the user is prompted for a User ID (this is

always admin) and Password (the default value is “admin”). It is HIGHLY recom-

mended to change to a secure password when initially conﬁ guring the Access

Point. To change the password, simply enter the new password, conﬁ rm the

password, then click Save, and then Reboot for the change to take effect.

After conﬁ rming the desired Quick Setup conﬁ guration settings, select Save and

then Reboot for the settings to take effect.

5.3 Wireless

5.3.1 Basic Wireless Settings

Basic Wireless Settings: This screen allows the modiﬁ cation of the following basic

settings for the wireless network:

User Guide

Wireless Radio: This ﬁ eld is used to Enable and Disable the wireless network

and is set to Enabled by default. If the Radio is Disabled the Access Point will not

broadcast a wireless signal. To Disable the Wireless Radio, click the dropdown

menu, select Disabled, then click Save and then Reboot for the change to take

effect.

Channel: This ﬁ eld allows the user to set which 2.4GHz channel to use. The

default is set to Channel 6 and is the recommended setting due to the Access

Point being optimized to run on Channel 6. However, any other channel (1-11) may

be selected. To change the Channel, click the dropdown menu, select the desired

channel, then click Save and then Reboot for the change to take effect.

 Wireless Mode: Sets the type of 802.11 wireless network to be broadcast.

Available modes are:

11g (802.11g)

11gnHT20 (802.11g/n with 20MHz only channels)

11gnHT40+ (802.11g/n with 20/40MHz channels expanding to channels above

the set channel)

11gnHT40- (802.11g/n with 20/40MHz channels expanding to channels below

the set channel)

The default setting is 11gnHT20, and is recommended for optimal performance of

all types of devices in the network. Use the 11g Mode ONLY if there are 802.11b/g

client devices in the network that will not connect in 11gnHT20 Mode. 11gnHT40+

and 11gnHT40- Modes should only be used when all client devices in the network

are 802.11n and capable of supporting 40MHz channels.

Channel Width: Sets the width of the 802.11n channel. Available widths are:

20MHz (only available for 11g and 11gnHT20 modes)

40MHZ (only available for 11gnHT40+ and 11gnHT40-)

20/40MHz Auto (available for all modes)

The default (and recommended) setting is 20/40 MHz Auto to provide maximum

performance to all client devices and to avoid any potential client issues.

NOTE: HT40 mode will use two channels. For example, if HT40- is

selected and the radio is using channel 6, it would also use

channel 1. If HT40+ is selected and the radio is using channel 6, it

would also use channel 11.

If making any change to the Wireless Settings, select Save and then Reboot for the

settings to take effect.

Other manuals for XAP-1010

Table of contents

Popular Wireless Access Point manuals by other brands

Fortinet

Fortinet FortiAP 320B quick start guide

Ubiquiti

Ubiquiti PBE-M5-400 quick start guide

Cisco MERAKI

Cisco MERAKI MR57 installation guide

NETGEAR

NETGEAR WG302v1 - ProSafe 802.11g Wireless Access... Product specifications

TP-Link

TP-Link Auranet EAP120 installation guide

Devolo

Devolo dLAN 1200+ Installation

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-LR quick start guide

Alcatel-Lucent

Alcatel-Lucent OmniAccess 700 CLI Command reference guide

Pakedge

Pakedge WA Series Deployment guide

Ubiquiti

Ubiquiti NBE-M5-16 quick start guide

Buffalo

Buffalo WLA-G54C user manual

ALTAI

ALTAI A2 installation guide

EnGenius

EnGenius ENS200EXT quick start guide

VT Miltope

VT Miltope nMAP2 quick start guide

TRENDnet

TRENDnet TEW-610APB user guide

Cisco

Cisco Aironet 1550 Series Hardware installation guide

Avaya

Avaya AP-3 user guide

TRENDnet

TRENDnet TPL-410AP Quick installation guide

Luxul XAP-1010 User manual

Popular Wireless Access Point manuals by other brands