Lynxspring JENEsys Edge 534 User manual

www.lynxspring.com
1210 NE Windsor Drive
Lee’s Summit, MO 64086
[e-mail]
1 [phone]
© 2018 Lynxspring, Inc.
All Rights Reserved
Revised 4/24/2018
JENE-EG534-V1
Page 1 of 5
JENEsys
®
Edge™534
WIRING INSTALLATION GUIDE—NIAGARA AX
Estimated installation time = 15-30 minutes
Wiring Details
Figure 1

www.lynxspring.com
1210 NE Windsor Drive
Lee’s Summit, MO 64086
[e-mail]
1 [phone]
© 2018 Lynxspring, Inc.
All Rights Reserved
Revised 4/24/2018
JENE-EG534-V1
Page 2 of 5
JENEsys
®
Edge™534
WIRING INSTALLATION GUIDE—NIAGARA AX
Power Wiring
The JENEsys Edge 534 can be powered by wiring to a dedicated Class 2, 24 Vac transformer, or to a 24 Vdc power
source. As shown in Figure 1, the JENEsys Edge 534’s 3-position power connector
(black) is located at the top corner
of the unit. Unplug the connector from the device and make connections to it as shown.
Note: Do not apply 24 Vac power (reinsert connector plug into the JENEsys Edge 534) until all other wiring is
completed, including JENEsys Edge 534 inputs and outputs. Do not power other equipment with it.
Inputs
Each of the 16 universal inputs can support any one of the following:
Type-3 10 k ohm Thermistor
Resistive 0-100 k ohms
0-10 Vdc
4-20 mA
Thermistor
The inputs support 10 k Thermistor temperature sensors using a ThermistorInputPoint.Input accuracy is in the range of
±1% of span. By default, conversion is for a standard Type-3 thermistor sensor, with a sensor range of -10° to
135° F
(-23.3° to 57.2° C). Using a conversion type of Tabular Thermistor , you can specify a different thermistor response
curve, by importing a thermistor curve .xml file.
Pulse
Pulse contacts may have a change-of-state (COS) frequency of up to 500 Hz with a 50% duty cycle.
Note: Minimum dwell time must be > 2ms. For a pulse contact, use the CounterInputPoint in the station database.
Resistive 0-100 k ohms
The inputs can read a resistive signal within a range from 0 to 100,000 ohms. Wiring is the same as shown for a
Thermistor temperature sensor (Figure 2). Resistive signals require a Resistive Input Point.
Note: The universal input option is optimized to provide the best resolution around the 10 k ohm range. For a sensor
with a range far from 10 k ohms
(such as a 100-ohm or 1,000-ohm type), resolution will be poor. To use such a
sensor, it is recommended you install a transmitter that produces a Vdc or mA signal, and then wire the transmitter
to the UI according to the 0–10 Vdc or 4–20 mA instructions.
Figure 2

www.lynxspring.com
1210 NE Windsor Drive
Lee’s Summit, MO 64086
[e-mail]
1 [phone]
© 2018 Lynxspring, Inc.
All Rights Reserved
Revised 4/24/2018
JENE-EG534-V1
Page 3 of 5
JENEsys
®
Edge™534
WIRING INSTALLATION GUIDE—NIAGARA AX
0-10 Vdc
The inputs support self-powered 0–10 Vdc sensors. Input impedance is greater than 5K ohms. 0–10 volt accuracy is ±
2% of span, without user calibration. Figure 3 shows the wiring diagram. 0–10 Vdc sensors require a
VoltageInputPoint.
4-20 mA
The inputs support self-powered 4–20 mA sensors. Input accuracy is ± 2% of span, without user calibration. Figure 4
shows the wiring diagram, which requires a 499 ohm resistor wired across the input terminals. 4–20 mA sensors also
require the VoltageInputPoint.
Figure 4
Figure 3
Binary Input
Boolean Input Resistive
Inputs read a 0-100,000 ohm resistive signal. If the signal is above the threshold (50 k ohms by default), the Boolean
value of false is reported. If the signal is below the threshold, the Boolean value of true is reported. The threshold value
can be changed by displaying and editing it.
Boolean Input Voltage
Inputs read the voltage signal of self-powered 0-10 Vdc devices. If the signal is above the threshold (5 Vdc by default) ,
the Boolean value of true is reported. If the signal is below the threshold, the Boolean value of false is reported.
The threshold value can be changed by displaying and editing it.
Boolean Input Current
Inputs read the current signal of self-powered 4-20 mA devices. If the signal is above the threshold (12 mA by default) ,
the Boolean value of true is reported. If the signal is below the threshold, the Boolean value of false is reported.
The threshold value can be changed by displaying and editing it.

www.lynxspring.com
1210 NE Windsor Drive
Lee’s Summit, MO 64086
[e-mail]
1 [phone]
© 2018 Lynxspring, Inc.
All Rights Reserved
Revised 4/24/2018
JENE-EG534-V1
Page 4 of 5
JENEsys
®
Edge™534
WIRING INSTALLATION GUIDE—NIAGARA AX
LED Indicators
LED indicators are provided to display status and activity. Become familiar with these indicators for a quick visual device
reference.
The Power LED should be lit when 24 V power is applied to the device.
For the Heartbeat LED, there are three modes of operation:
A fast beat with a 50% duty cycle when the device is booting
A slow beat with a 50% duty cycle when the platform is started
A double beat when the station has started
The Lightning Bolt LED shows the Onyxx network is actively communicating to and from the device.
An LED status indicator for each relay (D1–D10) is located on the cover (Figure 6). Under normal operation, each digital
status LED indicates activity as follows:
Off–relay high-impedance/no current flow
On–relay low-impedance/load current flow; relay is closed and the load is powered
Outputs
There are ten (10) N.O. digital relay outputs and eight (8) 0–10 volt analog
outputs.
Relay Outputs
Each relay output is rated at 24 Vac or Vdc at 0.5A.
Use a
BooleanOutputWritable
in the station for each output.
Figure 5
shows an example wiring diagram.
Note:
The 15-position DO connector has common
terminals marked “C” that are isolated from each other.
This is useful if controlled loads are powered from different circuits.
Figure 6

www.lynxspring.com
1210 NE Windsor Drive
Lee’s Summit, MO 64086
[e-mail]
1 [phone]
© 2018 Lynxspring, Inc.
All Rights Reserved
Revised 4/24/2018
JENE-EG534-V1
Page 5 of 5
JENEsys
®
Edge™534
WIRING INSTALLATION GUIDE—NIAGARA AX
Analog Outputs
Analog outputs (AO) are referenced by the terminals labeled “A(n)” and “C” (ground) . Each AO can supply a maximum of
20 mA over the entire 0 to 10 Vdc range. The minimum input impedance of a device controlled by an AO must be greater
than 2,500 ohms. Typical wiring for an AO is shown in Figure 7.
For each AO, use a VoltageOutputWritable in the station database.
Onyxx®IO (Software) Representation
In the Niagara station interface, the JENEsys Edge 534 appears as one Onyxx IO Device, where the “DevicePath” property
is appended with a six-digit number. See Figure 8. Upon discovery, if the JENEsys Edge 534 has 1-7 Onyxx XM 34IOs
daisy-chained, the devices will show up as onyxx_######. The device number will match the number listed on the device
itself.
Refer to the physical devices to verify the device ID number and match it to the discovered device. They may not appear
in the wired order so verification must be completed for proper device and point allocation to the physical Onyxx device.
See Figure 8. Each type of input or output used requires a special Lynxspring Input/Output (Onyxx IO) point to be added
in the station database. These components act as the station interface to the physical I/O points.
The Onyxx IO points you need for each input or output type are noted in previous wiring sections in boldface.
Figure 8
Note: Add to a JENE-EG534, up to 8 additional
extender modules (at 34 points of IO each) for a
maximum of 306 points.
For further reference, please view the wiring “How To” videos available on our website:
http://www.lynxspring.com/company/how-to-videos
Figure 7