Lynxspring JENEsys Edge 534 User manual

www.lynxspring.com
JENEsys
®
Edge™534 – N4
WIRING INSTALLATION GUIDE
1210 NE Windsor Drive
Lee’s Summit, MO 64086
[e-mail]
1 [phone]
© 2019 Lynxspring, Inc.
All Rights Reserved
Revised 1/10/2019
JENE-EG534-N4-V1
Page 1 of 5
Estimated wiring time = 15-30 minutes
Wiring Details
Figure 1

www.lynxspring.com
JENEsys
®
Edge™534 – N4
WIRING INSTALLATION GUIDE
1210 NE Windsor Drive
Lee’s Summit, MO 64086
[e-mail]
1 [phone]
© 2019 Lynxspring, Inc.
All Rights Reserved
Revised 1/10/2019
JENE-EG534-N4-V1
Page 2 of 5
Power Wiring
The JENEsys Edge 534 – N4 can be powered by wiring to a dedicated Class 2, 24 Vac transformer, or to a 24 Vdc power
source. As shown in Figure 1, the JENEsys Edge 534 – N4’s 3-position power connector (black) is located at the top corner of
the unit. Unplug the connector from the device and make connections to it as shown.
Note: Do not apply 24 Vac power (reinsert connector plug into the JENEsys Edge 534 – N4) until all other wiring is completed,
including JENEsys Edge 534 – N4 inputs and outputs. Do not power other equipment with it.
Inputs
Each of the 16 universal inputs can support any one of the following:
Type-3 10 k ohm Thermistor
Resistive 0-100 k ohms
0-10 Vdc
4-20 mA
Binary Input
Thermistor
The inputs support 10 k Thermistor temperature sensors using a ThermistorInputPoint. Input accuracy is in the range of
±1% of span. By default, conversion is for a standard Type-3 thermistor sensor, with a sensor range of -10° to 135°F
(-23.3° to 57.2°C). Using a conversion type of Tabular Thermistor , you can specify a different thermistor response curve,
by importing a thermistor curve .xml file.
Resistive 0-100 k ohms
The inputs can read a resistive signal within a range from 0 to 100 k ohms. Wiring is the same as shown for a Thermistor
temperature sensor (Figure 2). Resistive signals require a ResistiveInputPoint.
Note: The universal input option is optimized to provide the best resolution around the 10 k ohm range. For a sensor with a
range far from 10 k ohms
(such as a 100 ohm or 1,000 ohm type), resolution will be poor. To use such a sensor, it is
recommended you install a transmitter that produces a Vdc or mA signal, and then wire the transmitter to the UI
according to the 0–10 Vdc or 4–20 mA instructions.
Figure 2

www.lynxspring.com
JENEsys
®
Edge™534 – N4
WIRING INSTALLATION GUIDE
1210 NE Windsor Drive
Lee’s Summit, MO 64086
[e-mail]
1 [phone]
© 2019 Lynxspring, Inc.
All Rights Reserved
Revised 1/10/2019
JENE-EG534-N4-V1
Page 3 of 5
0-10 Vdc
The inputs support self-powered 0–10 Vdc sensors. Input impedance is greater than 5 k ohms. 0–10 volt accuracy is ± 2% of
span, without user calibration. Figure 3 shows the wiring diagram. 0–10 Vdc sensors require a VoltageInputPoint.
4-20 mA
The inputs support self-powered 4–20 mA sensors. Input accuracy is ± 2% of span, without user calibration. Figure 4 shows
the wiring diagram, which requires a 499 ohm resistor wired across the input terminals. 4–20 mA sensors also require the
CurrentInputPoint.
Binary Input
Pulse
Pulse contacts may have a change-of-state (COS) frequency of up to 500 Hz with a 50% duty cycle.
Note: Minimum dwell time must be > 2 ms. For a pulse contact, use the CounterInputPoint in the station database.
Outputs
There are ten (10) N.O. digital relay outputs and eight (8) 0–10 volt analog outputs.
Relay Outputs
Each relay output is rated at 24 Vac or Vdc at 0.5 A.
Use a BooleanOutputWritable in the station for each output. Figure 5 (page 4) shows an example wiring diagram.
Note:The 15-position DO connector has common terminals marked “C” that are isolated from each other. This is useful if
controlled loads are powered from different circuits.
Figure 3
Figure 4

www.lynxspring.com
JENEsys
®
Edge™534 – N4
WIRING INSTALLATION GUIDE
1210 NE Windsor Drive
Lee’s Summit, MO 64086
[e-mail]
1 [phone]
© 2019 Lynxspring, Inc.
All Rights Reserved
Revised 1/10/2019
JENE-EG534-N4-V1
Page 4 of 5
LED Indicators
LED indicators are provided to display status and activity. Become familiar with these indicators for a quick visual device
reference.
The Power LED should be lit when 24 V power is applied to the device.
For the Heartbeat LED, there are three modes of operation:
A fast beat with a 50% duty cycle when the device is booting
A slow beat with a 50% duty cycle when the platform is started
A double beat when the station has started
The Lightning Bolt LED shows the Onyxx network is actively communicating to and from the device.
An LED status indicator for each relay (D1–D10) is located on the cover (Figure 6). Under normal operation, each digital status
LED indicates activity as follows:
Off–relay high-impedance/no current flow
On–relay low-impedance/load current flow; relay is closed and the load is powered
Figure 5
Figure 6

www.lynxspring.com
JENEsys
®
Edge™534 – N4
WIRING INSTALLATION GUIDE
1210 NE Windsor Drive
Lee’s Summit, MO 64086
[e-mail]
1 [phone]
© 2019 Lynxspring, Inc.
All Rights Reserved
Revised 1/10/2019
JENE-EG534-N4-V1
Page 5 of 5
Analog Outputs
Analog outputs (AO) are referenced by the terminals labeled “A(n)” and “C” (ground). Each AO can supply a maximum of 20
mA over the entire 0 to 10 Vdc range. The minimum input impedance of a device controlled by an AO must be greater than
2,500 ohms. Typical wiring for an AO is shown in Figure 7.
For each AO, use a VoltageOutputWritable in the station database.
Onyxx®IO (Software) Representation
In the Niagara 4 station interface, the JENEsys Edge 534 – N4 appears as one Onyxx IO Device, where the “DevicePath”
property is appended with a six-digit number. See Figure 8. Upon discovery, if the JENEsys Edge 534 – N4 has 1-7 Onyxx XM
34IOs daisy-chained, the devices will show up as onyxx_######. The device number will match the number listed on the
device itself, unless different devices were programmed in the station previously. Refer to the physical devices to verify the
device ID number and match it to the discovered device. They may not appear in the wired order so verification must be
completed for proper device and point allocation to the physical Onyxx device. See Figure 8. Each type of input or output
used requires a special Lynxspring Input/Output (Onyxx IO) point to be added in the station database. These components act
as the station interface to the physical I/O points. The Onyxx IO points you need for each input or output type are noted in
previous wiring sections in boldface.
Figure 7
Figure 8
Note: Add to a JENE-EG534-N4, up to 8
additional extender modules (at 34 points of IO
each) for a maximum of 306 points.