M-LOCKS MiniTech T9520 User manual

T9520
MiniTech
M-LOCKS BV Tel: [phone]
Vlijtstraat 40 ver. 1.0 2012 11 16 Fax: [phone]
NL-7005 BN Doetinchem 1 www.m-locks.com
Keypads with display
Technical manual
STATIONARY MOUNTING
Route the cable through the cable
hole.
Affix the two mounting screws.
Remove the protective film from the membrane,
carefully align the margins and stick it to the housing.
Connect one (1) battery to the battery clip. Only use
9V-ALKALINE batteries from brand name
manufacturers like DURACELL
TM
.
TURNABLE MOUNTING
Affix the bearing plate with the two mounting adapters (M4).
Insert the spring and the pin into the hole on the back cover.
Cut the grooved shaft to the appropriate length.
Insert the grooved shaft, with the cut-off edge first, all the way into the entry housing. Push the
cable into the groove until flat over the entire length of the shaft. Route the cable and shaft
through the spindle hole of the door, hold the unit at an approximately 10:00 o’clock position,
and slide it on the mounting adapters. Turn unit clockwise until it clicks into straight position at
12:00.
Remove the protective film from the membrane, carefully align the margins and stick it to the
housing.
Connect one (1) battery to the battery clip. Only use 9V-ALKALINE batteries from brand name
manufacturers like DURACELL
TM
.

T9520
MiniTech
M-LOCKS BV Tel: [phone]
Vlijtstraat 40 ver. 1.0 2012 11 16 Fax: [phone]
NL-7005 BN Doetinchem 2 www.m-locks.com
KEYPAD DIMENSIONS AND GENERAL INFORMATION
With mounting plate add 3mm to thickness; with turnable plate add 9,7mm.
The diameter of the hole cable should be minimum 9mm,
maximum 12mm.
Prepare mounting and cable holes as indicated in the picture.
The hole must be deburred well to avoid damage to the cable.
Once the keypad has been mounted no more welding can be done on the safe.
ROTOBOLT LOCK
In the LOCKED position, there should be approximately 1mm clearance
between the lock bolt and the cavity in the blocking bar of the boltwork.
The lock bolt must move freely into the cavity.
Only use M-Locks supplied screws to mount the lock.
Tighten the screws securely so the lock body is attached firmly to the
mounting surface. Do not overtorque mounting screws. Maximum torque
3.5Nm.
Make sure there is an air space on all sides of the lock bolt when the safe’s boltwork is fully
thrown into locked position.

T9520
MiniTech
M-LOCKS BV Tel: [phone]
Vlijtstraat 40 ver. 1.0 2012 11 16 Fax: [phone]
NL-7005 BN Doetinchem 3 www.m-locks.com
ROTOBOLT DIMENSIONS
Insert the keypad cable into the “ENT” connector of the lock. Check that the cable is
completely seated (to remove it lift it up and carefully pull it out).
Battery box or alarm interfaces will be connected to the “BAT” connector of the lock.
Tie cables away from moving parts.
Connect a 9V-ALKALINE battery and repeat functional test (with door open) several times
before locking the safe door.
STRAIGHTBOLT LOCK
In the LOCKED position, there should be approximately 1mm clearance
between the lock bolt and the cavity in the blocking bar of the boltwork. The
lock bolt must move freely into the cavity.
In OPEN position, there should be minimum 3mm and
maximum 5mm clearance between the lock bolt and the
blocking bar of the boltwork.
The force applied to the bolt must not exceed 1kN.
Only use M-Locks supplied screws to mount the lock. Tighten the screws securely so the lock
body is attached firmly to the mounting surface. Do not overtorque mounting screws.
Maximum torque 3.5Nm.

T9520
MiniTech
M-LOCKS BV Tel: [phone]
Vlijtstraat 40 ver. 1.0 2012 11 16 Fax: [phone]
NL-7005 BN Doetinchem 4 www.m-locks.com
Make sure there is an air space on all sides of the lock bolt when the safe’s boltwork is fully
thrown into locked position.
The grooved shaft must extend between 6 and 11mm off the mounting surface: there must be
at least 4mm clearance between the shaft and the lock cover to avoid cable damages during
the use of the lock. The shaft must be deburred well to avoid damage to the cable.
STRAIGHTBOLT DIMENSIONS
Make sure the cable is in the groove. Insert the cable connector into the square hole in the
bottom of the lock and guide it through the hole in the lock cover.
Holding the cable straight place the lock with the square cavity on the grooved shaft and then
screw it to the mounting surface.
Insert the keypad cable into the “ENT” connector of the lock. Check that the cable is
completely seated (to remove it lift it up and carefully pull it out). To tie the cable, push it into
the square groove in the lock cover. Battery box or alarm interfaces will be connected to the
“BAT” connector of the lock.
Connect a 9V-ALKALINE battery and repeat functional test (with door open) several times
before locking the safe door.
Never remove label on lock cover, this voids the warranty.