M-LOCKS T8530 User manual

USER INSTRUCTIONS
T8530
M-LOCKS BV Tel: [phone]
Vlijtstraat 40 ver. 1.0 2010 12 29 Fax: [phone]
NL-7005 BN Doetinchem
1 www.m-locks.com
MASTER MENU
The Master Menu gives the owner of the Master Code access to the following functions:
• Set time and date
• Set time lock (T.L.) (standard week and special events)
• Change code
To get access to the Master Menu, press button . Access to the Master Menu is not allowed
during time delay counting!
The LCD screen will show the following message:
Enter the 8-digit Master Code (default 1-2-3-4-5-6-7-8).
After the 4th consecutive wrong code, a time penalty of 4 minutes will be started. The LCD screen will
then show the following message:
During penalty time the LED flashes every 10 seconds. Every code entry will be rejected by a long
signal.
To enter into the Menu, press button .To select a function, press button .
In case no operation is done in the Master Menu within 30 seconds, the system will automatically
switch off.
Enter
MASTER code
Penalty

USER INSTRUCTIONS
T8530
M-LOCKS BV Tel: [phone]
Vlijtstraat 40 ver. 1.0 2010 12 29 Fax: [phone]
NL-7005 BN Doetinchem
2 www.m-locks.com
Time and Date Menu
Use this menu to check or change settings for time and date.
To set time and date, enter new values through the entry unit and press the button to confirm. To
exit the Time and Date Menu press button .The entry unit will check the validity of the entered
data of time and date. In case an error is found the display screen will show an error message and the
entered (wrong) data will not be accepted. The display screen will show the previous time and date
values.
Daylight Saving Time is automatically updated for 20 years (if applicable).
Time Lock Menu
Use this menu to manage Time Lock functions (standard week and special events). Up to 4 different
opening periods a day and up to 15 special events per year can be programmed.
To enter the Menu, press button . To select a function, press button .
If no operation in the menu is done within 30 seconds, the Menu will automatically switch off.
• When the Time Lock is active, no modification is possible. Only time and date can be verified
in the Master Menu.
The LCD display will show the following message:
• If entered values will block the lock, the LCD display will show the following message:
To confirm, press button .
To exit the Menu, press button .
Standard week: “Add”
When this function is selected, the LCD display will show the following message (the system will
automatically suggest the present/current day):
Enter Time Lock values for the selected day.
• Press button to store/save the entered data. All data will be saved when leaving the
Master Menu. If the keypad automatically switches off before the Master exits his menu, the
data will not be saved.
24/06/08 TUE (dd/mm/yy)
08 : 52 : 00
T.L. Active!!!
 00 : 00 TUE
00 : 00
T.L. Active in
Exit. Confirm?

USER INSTRUCTIONS
T8530
M-LOCKS BV Tel: [phone]
Vlijtstraat 40 ver. 1.0 2010 12 29 Fax: [phone]
NL-7005 BN Doetinchem
3 www.m-locks.com
• If button is pressed, the system will automatically select the following day of the week,
and the entered data will not be saved.
• At the end of the list the LCD display will show the following message:
To enter further periods, press button . The system will select the current day. Enter new periods
as above. Repeat the procedure until the end of the list.
Press button to exit the Menu.
The entry unit will check the validity of the entered data. In case an error is found, the display will show
an error message.
NOTE: Time Lock periods cannot overlap; if so, only the last entered period will be accepted.
Standard week: “Verify & Delete”
When this function is selected, the LCD display will show all entered Time Lock periods in order of
time, starting from the current day.
• To run the Menu, press button until LCD display shows the message ´End of List´.
• To delete a period, press button . The LCD display will show the following message:
• Press button to confirm and remove the period.
Special Events: “Add”
When this function is selected, the display will show the following message:
Enter the special event period.
• Press the button to confirm and save.
• If the button is pressed, the system will exit this function without saving the entered data.
The entry unit will check the validity of the entered data. If any error is found, the LCD display will
show en error message.
NOTE:
• The programmed period will be repeated every year.
• 15 different periods are available. A period can not exceed 14 days.
• Special event periods cannot overlap. If so, only the last entered period will be accepted.
Exit from Master
Menu to save
 00 : 00 TUE
00 : 00
Delete?
DD / MM hh : mm
DD / MM hh : mm

USER INSTRUCTIONS
T8530
M-LOCKS BV Tel: [phone]
Vlijtstraat 40 ver. 1.0 2010 12 29 Fax: [phone]
NL-7005 BN Doetinchem
4 www.m-locks.com
Special Events: “Verify & Delete”
When this function is selected, the display will show all entered special events, in order of time:
• To run the Menu, press button until the display shows the message ´End of List´.
• To delete a period, press button . The LCD display shows the following message:
• Press button to confirm and delete the special event.
Change Code
Use this menu to change the Master Code.
The LCD display shows the following message:
Enter the new 8-digit Master Code.
The LCD display will show the following message:
Confirm the new code.
If the new code is not accepted, the entry unit will emit a long sound signal (beep) and the entire
procedure has to be repeated.
IMMEDIATE AND TEMPORARY TIME LOCK
This function allows users to start up an immediate and temporary time lock.
To get access to this function press the button and then button .
Once entered this function, if no operation is done within 30 seconds, the system will automatically
switch off.
Access to this function is not allowed during the Time Delay period.
• If a Time Lock period has already been programmed, the LCD display will show the following
message:
DD / MM hh : mm
DD / MM hh : mm
Delete?
Enter
New code
Confirm
New code
Immediate T.L.
MON 23/06 08 : 00

USER INSTRUCTIONS
T8530
M-LOCKS BV Tel: [phone]
Vlijtstraat 40 ver. 1.0 2010 12 29 Fax: [phone]
NL-7005 BN Doetinchem
5 www.m-locks.com
NOTE:
Immediate Time Lock: this function starts up Time Lock immediately. It will not be possible to open the
lock until the next programmed opening period. In case the Immediate Time Lock is selected (Time
Lock standard week has to be programmed), the LCD display will show the first available opening
period. If the first available Opening Period coincides with a special event, the LCD display will show
the end of this special event as the next available Opening Period.
• If a Time Lock Opening Period has not been programmed yet, or the user presses one digit,
the display shows the following message (the entered digit corresponds with the first digit of
the date):
NOTE:
Temporary Time Lock: this function starts up the Time Lock immediately. It is not possible to open the
lock until time and date are programmed. When the temporary time lock is selected, LCD requires to
introduce opening time and date (maximum 14 consecutive days).
• Press button to save entered data.
• If the button is pressed the system will exit the function and entered data will not be
saved.
The entry unit will verify the validity of the entered data. In case an error is found, the display will show
an error message.
To confirm Immediate/ Temporary Time Lock, use a valid user code. The LCD display will then show
the following message::
If a wrong code is entered, a buzzer will emit a long sound signal (beep) and the entry unit will exit the
function.
Temporary T.L.
MON 23/06 08 : 00
Enter Code
To activate T.L.