M-LOCKS T9530 Techmaster User manual

Techmaster
M-LOCKS BV Tel: [phone]
Vlijtstraat 40 Fax: [phone]
NL-7005 BN Doetinchem 1 www.m-locks.com
⇒
Display
Foil keypad
User Manual
T9530
OPENING USER
Press any key to activate the display.
On the display USER CODE will appear.
If you are registrated as user, enter your code.
If timedelay is not programmed on the display OPEN will appear
Turn the handle and open the door.
If a wrong or an invalid code is entered on the display WRONG
CODE will appear.
OPENING MANAGER
Press any key to activate the display.
On the display USER CODE will appear.
If you are registrated as manager, press and enter the
6-digits managercode
If timedelay is not programmed on the display OPEN will appear
Turn the handle and open the door.
If a wrong or an invalid code is entered on the display WRONG
CODE will appear.
USER CODE
1 XX-XXXXXX
OPEN
USER CODE
1 XX-XXXXXX
MANAGER CODE
1 XX-XXXXXX
OPEN
WRONG CODE
Confirm key
Programm key
WRONG CODE

Techmaster
M-LOCKS BV Tel: [phone]
Vlijtstraat 40 Fax: [phone]
NL-7005 BN Doetinchem 2 www.m-locks.com
√
⇒
⇒
⇒
⇒
CHANGE MANAGER CODE
Press any key to activate the display.
On the display USER CODE will appear.
Press the key to enter the main menu.
On the display will appear:
Press the key (2x) until you enter the menu Change Code
Then confirm with key
Press key once and select Change Manager code.
Then confirm with key
Enter old code (when known), then enter new 6-digit code and
confirm once more. When everything is correct, following
message will show on display:
Press the key several times until EXIT will show on
display. Confirm with key . Without pressing any key, the
display will automatically be turned off after 20 seconds.
CHANGE USER CODE
Press any key to activate the display.
On the display USER CODE will appear.
Press the key to enter the main menu.
On the display will appear:
Press the key (2x) until you enter the menu Code Change.
Confirm with key
MASTER MENU
1= XXXXXXXX
CHANGE CODE
USER CODE
1 XX-XXXXXX
OLD CODE
XXXXXX
CHANGE MANAGER
CODE
OPERATION DONE
MASTER MENU
1= XXXXXXXX
USER CODE
1 XX-XXXXXX
CHANGE CODE
CHANGE USER
CODE

Techmaster
M-LOCKS BV Tel: [phone]
Vlijtstraat 40 Fax: [phone]
NL-7005 BN Doetinchem 3 www.m-locks.com
⇒
⇒
⇒
Press key to change user code
The display will show OLD CODE
Enter old code (when known), then enter new 6-digit code and
confirm once more. When everything is correct, following
message will show on display:
Press the key several times until EXIT will show on
display. Confirm with key Without pressing any key, the
display will automatically be turned off after 20 seconds.
MANAGEMENT USER
Press any key to activate the display.
On the display USER CODE will appear.
Press the key to enter the main menu.
On the display will appear:
Press key to enter the MANAGER MENU
Enter the 6-digit Manager code, then display will show:
Confirm with key to enter the menu. The display will show
an overview of active users.
Note:
V = Active user
_ = Free position
X = Blocked user (occupied position)
Enter the ID-number that you want to manage. The cursor will
move to the right position (visible by the blinking cursor)
e.g. ID-02
Confirm with key
In case you wish to install ID-number 02, confirm with key
In case you wish to block or delete the position, proceed with
key and confirm this action with key
OLD CODE
XX-XXXXXX
OPERATION DONE
USERS
MANAGEMENT
USER CODE
1 XX-XXXXXX
MASTER MENU
1= XXXXXXXX
MANAGER MENU
1= XXXXXXXX
02 03 04 05 06 07
V _ _ _ _ X
02 03 04 05 06 07
V _ _ _ _ X
02 _ t1
Install?

Techmaster
M-LOCKS BV Tel: [phone]
Vlijtstraat 40 Fax: [phone]
NL-7005 BN Doetinchem 4 www.m-locks.com
⇒
Enter the new 6-digit code, and confirm this code once more.
When everything is correct, following message will show on
display:
You will enter the USER Overview
Press the key several times until EXIT will show on the
display. Confirm with key Without pressing any key, the
display will automatically be turned off after 20 seconds.
NEW CODE
OPERATION DONE
02 03 04 05 06 07
V _ _ _ _ X