M-system 61F User manual

BEFORE USE
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
Analog I/O module (body + base socket) ............................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■POWER INPUT RATING & OPERATIONAL RANGE
• Locate the power input rating marked on the product and
confirm its operational range as indicated below:
85 – 132V AC rating: 85 – 132V, 47 – 66 Hz, approx. 3VA
24V DC rating: 24V ±10%, approx. 4W, approx. 160mA
■GENERAL PRECAUTIONS
• Before you remove the unit or mount it, turn off the power
supply, input signal and output signal for safety.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -5 to +55°C
(23 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
INSTALLATION
Use the Installation Base (model: MxBS2).
ANALOG I/O MODULE
(Fuji Electric T-Link use) MODEL 61F
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-6635 Rev.2 P. 1 / 3
INSTRUCTION MANUAL

COMPONENT IDENTIFICATION
Body
Specifications
1
2
3
4
5
6
7
8
9
0

1
2
3
4
5
6
7
8
9
0

■FRONT PANEL CONFIGURATION
L RUN
PU-2x
STATION NO.
L ERR.
L I／O
L COM
PWR
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
X 1
X 10
D
E
C
B
A
NAME FUNCTIONS
AModular jack for
factory calibration
Used only for factory calibration.
BPower indicator
LED
MARKING (color) FUNCTIONS
PWR (green) ON: Powered.
OFF: No Power
CStation No. setting Selectable within 00 – 99. (factory set to: 00)
DStatus indicator
LED
MARKING (color) FUNCTIONS
L RUN (red) ON: Normal Communication
OFF: Communication Cutoff (Timeout Error)
L ERR. (red) ON: Communication Data Error
OFF: Normal Communication
L I/O (red) Blinking during normal I/O function
L COM (red)
Blinking during normal T-Link Communication
EEuro type connec-
tor terminal for
T-Link
For wiring to T-Link
61F
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-6635 Rev.2 P. 2 / 3

TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
■EXTERNAL DIMENSIONS unit: mm (inch)
50 (1.97) 103 (4.06)38 min.
(1.50)
12
(.47)
80 (3.15)
100 (3.94)
2–M3 SCREWS
■CONNECTION DIAGRAM
+
−
Shielded
Twisted-pair Cable
To Other
T-Link Devices
*Jumper Pin
T1
T2
SD
RT+
RT−
Terminating
Resistor
* When the unit is located at the end of transmission line via twisted-pair cable
(= no cross-wiring), short across the RT+ and RT– terminals with the jumper pin
(or wire) provided with the unit.
Remove the jumper pin for the one not located at the end.
Note: Use terminals T1, T2 and SD for cross-wiring.
Modular Jack
for Factory
Calibration
MODULAR JACK
I/O & POWER CONNECTOR
To
Installation
Base
WIRING INSTRUCTIONS
■EURO TYPE CONNECTOR TERMINAL (T-Link)
Applicable wire size: 0.2 to 2.5 mm2(AWG24 to 12)
Stripped length: 7 mm
LIGHTNING SURGE PROTECTION
M-System offers a series of lightning surge protectors for
protection against induced lightning surges. Please contact
M-System to choose appropriate models.
61F
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-6635 Rev.2 P. 3 / 3