M-system TR30 User manual

1TR30-G USERS MANUAL EM-8631-G Rev.16
Paperless Recorder TR30 Series
PAPERLESS RECORDER
Model: TR30-G
USERS MANUAL
http://www.m-system.co.jp/
5-2-55, Minamitsumor
i, Nishinari-ku, Osaka 557-0063 JAPA
N
Te l: [phone] Fax: [phone]
E-mail: [e-mail]

2TR30-G USERS MANUAL EM-8631-G Rev.16
Table of Contents
1. Introduction 8
1.1 User manual compatible versions ......................................................................................................8
1.2 Precautions ........................................................................................................................................9
1.3 Component identication ................................................................................................................. 10
2. Installation 12
2.1 Preparations .................................................................................................................................... 12
2.2 Installation and wiring...................................................................................................................... 12
2.3 Preparation of congurator software................................................................................................ 13
2.3.1 Congurator software for the TR30: TRGCFG ......................................................................................... 13
Installation ...................................................................................................................................... 13
TRGCFG startup ............................................................................................................................ 13
2.3.2 Congurator software for the I/O module: R30CFG................................................................................. 15
Installation ...................................................................................................................................... 15
R30CFG startup ............................................................................................................................. 15
2.4 Explanation about the basic working and terms.............................................................................. 16
3. Setting 17
3.1 Setting ow ...................................................................................................................................... 17
3.2 Setting during initial startup ............................................................................................................. 18
3.3 Network setting................................................................................................................................20
3.3.1 Connect using a local area network (LAN) ..............................................................................................21
3.3.2 Connect via the Internet (WAN) ...............................................................................................................21
3.3.3 Set the IP address ...................................................................................................................................22
3.3.4 Enable setup via a network......................................................................................................................23
3.4 System setting .................................................................................................................................26
Name..............................................................................................................................................27
Language........................................................................................................................................27
Time zone.......................................................................................................................................27
Daylight saving time........................................................................................................................27
Sampling adjustment at time correction..........................................................................................27
3.5 Built-in I/O module setting ...............................................................................................................28
3.6 Remote I/O connection setting ........................................................................................................29
3.7 SLMP device connection setting .....................................................................................................30
3.8 I/O setting ........................................................................................................................................31
3.8.1 I/O slave setting .......................................................................................................................................33
Assignment of remote I/O...............................................................................................................33
Assignment of SLMP device...........................................................................................................34
3.8.2 Communication Setting............................................................................................................................35

3TR30-G USERS MANUAL EM-8631-G Rev.16
3.8.3 Analog input (AI) ......................................................................................................................................36
Assignment of the I/O module to AI ................................................................................................36
Assignment of remote I/O to AI.......................................................................................................38
Assignment of SLMP device to AI...................................................................................................40
Assignment of control input to AI ....................................................................................................42
Assignment of time input to AI ........................................................................................................42
Basic setting (AI).............................................................................................................................44
Alarm zone setting (AI) ...................................................................................................................46
Upward setting / Downward setting (AI)..........................................................................................48
Alarm output (AI) ............................................................................................................................50
Reset totalized value (AI)................................................................................................................52
Reset function value (AI) ................................................................................................................54
3.8.4 Discrete input (DI) ....................................................................................................................................56
Assignment of the I/O module to DI................................................................................................56
Assignment of remote I/O to DI ......................................................................................................58
Assignment of SLMP device to DI ..................................................................................................60
Assignment of analog input (AI) for DI............................................................................................62
Assignment of control input to DI....................................................................................................63
Assignment of logic functions to DI ................................................................................................ 63
Basic setting (DI) ............................................................................................................................64
Alarm output (DI) ............................................................................................................................67
Reset totalized value (DI) ...............................................................................................................67
Reset function value (DI) ................................................................................................................67
3.8.5 Pulse input (PI) ........................................................................................................................................68
Assignment of the I/O module to PI................................................................................................68
Assignment of remote I/O to PI.......................................................................................................70
Assignment of SLMP device to PI ..................................................................................................72
Assignment of control input to PI.................................................................................................... 74
Assignment of the Analog accumulation to PI ................................................................................ 74
Assignment of the Discrete Input (DI) to PI .................................................................................... 76
Basic setting (PI).............................................................................................................................78
Alarm zone setting (PI) ...................................................................................................................79
Upward setting / Downward setting (PI)..........................................................................................80
Alarm output (PI) ............................................................................................................................82
Reset totalized value (PI)................................................................................................................84
Reset function value (PI) ................................................................................................................86
3.8.6 Function input (OI) ...................................................................................................................................88
Basic setting (OI) ............................................................................................................................88
Alarm zone setting (OI)...................................................................................................................91
Upward setting / Downward setting (OI) .........................................................................................92
Alarm output (OI)............................................................................................................................94
Reset totalized value (OI) ...............................................................................................................96
Reset function value (OI)................................................................................................................98
3.8.7 Discrete output (DO) .............................................................................................................................. 100
Assignment of the I/O module to DO............................................................................................ 100
Assignment of remote I/O to DO................................................................................................... 102
Assignment of SLMP device to DO .............................................................................................. 103
Basic setting (DO)......................................................................................................................... 104
Which functions assigned to DO?................................................................................................. 105
3.8.8 Copying the CH setting .......................................................................................................................... 106
3.8.9 Applying the setting................................................................................................................................ 107

4TR30-G USERS MANUAL EM-8631-G Rev.16
3.9 Web server setting......................................................................................................................... 108
3.9.1 Name setting.......................................................................................................................................... 108
3.9.2 Trend screen display setting................................................................................................................... 109
Pen setting.................................................................................................................................... 109
Page name setting.........................................................................................................................111
3.9.3 Login ID / password / port address setting............................................................................................. 112
3.9.4 Trend graph orientation setting (vertical/horizontal) ............................................................................... 114
3.10 Recording method setting............................................................................................................ 115
Storing rate ................................................................................................................................... 116
Auto start ...................................................................................................................................... 116
Auto le delete .............................................................................................................................. 116
SD card le format........................................................................................................................ 116
Start new memory block ............................................................................................................... 117
Limit on the number of CHs and number of pens per storing rate................................................ 117
Starting / stopping recording by channel ...................................................................................... 117
3.11 Communication function setting................................................................................................... 118
3.11.1 FTP server............................................................................................................................................ 118
3.11.2 FTP client.............................................................................................................................................. 120
3.11.3 SNTP .................................................................................................................................................... 122
3.11.4 Modbus/TCP slave................................................................................................................................ 124
3.11.5 Mail reporting ........................................................................................................................................ 126
SMPT / POP3 setting.................................................................................................................... 126
Mail setting.................................................................................................................................... 130
3.12 Other settings .............................................................................................................................. 139
3.12.1 TRGCFG setting .................................................................................................................................. 139
3.12.2 FTP status monitoring.......................................................................................................................... 140
Checking by TRGCFG.................................................................................................................. 140
Checking by a terminal software program .................................................................................... 141
4. How to use the Web server 142
4.1 Initial screen (Group selection screen) .......................................................................................... 142
4.2 Menu bar ....................................................................................................................................... 143
4.2.1 Display contents..................................................................................................................................... 143
Menu button.................................................................................................................................. 143
Memory block indicator................................................................................................................. 143
SD card indicator .......................................................................................................................... 143
Unacknowledged event indicator.................................................................................................. 143
Error indicator ............................................................................................................................... 144
Start recording button ................................................................................................................... 144
Screen lock indicator .................................................................................................................... 144
4.3 Trend.............................................................................................................................................. 145
4.3.1 Display contents..................................................................................................................................... 145
Page name ................................................................................................................................... 145
Digital display................................................................................................................................ 146

5TR30-G USERS MANUAL EM-8631-G Rev.16
4.3.2 Operation ............................................................................................................................................... 147
Switch pages ................................................................................................................................ 147
Switch scale (%, scaling value) .................................................................................................... 147
Change the maximum/minimum value of the scale...................................................................... 148
Switch between show / hide pen .................................................................................................. 149
Expand / compress the time axis.................................................................................................. 150
Compare graphs (Shifting the scale orientation)........................................................................... 151
Compare graphs (Scale expansion / contraction)......................................................................... 152
Comment entry............................................................................................................................. 153
Change screen refresh cycle ........................................................................................................ 153
4.4 New event...................................................................................................................................... 154
4.4.1 Display contents..................................................................................................................................... 154
Unacknowledged event (New event) ............................................................................................ 154
4.4.2 Operation ............................................................................................................................................... 155
Filter the display by event number (New event) ............................................................................ 155
Conrm an unacknowledged event (New event) .......................................................................... 156
Display historical trend.................................................................................................................. 157
Delete from new events ................................................................................................................ 158
4.5 Overview ....................................................................................................................................... 159
4.5.1 Display contents..................................................................................................................................... 159
4.5.2 Operation ............................................................................................................................................... 160
Display the enlarged screen ......................................................................................................... 160
4.6 Event summary ............................................................................................................................. 162
4.6.1 Display contents..................................................................................................................................... 162
Unacknowledged event (Event summary) .................................................................................... 162
4.6.2 Operation ............................................................................................................................................... 163
Filter the display by event number (Event summary).................................................................... 163
Conrm an unacknowledged event (Event summary) .................................................................. 164
4.7 Comment summary ....................................................................................................................... 165
4.7.1 Display contents ..................................................................................................................................... 165
4.7.2 Operation................................................................................................................................................ 165
Edit comment................................................................................................................................ 165
Delete comment ........................................................................................................................... 166
4.8 Group selection ............................................................................................................................. 167
4.9 Internal memory ............................................................................................................................ 168
4.9.1 Display contents..................................................................................................................................... 168
4.9.2 Operation ............................................................................................................................................... 169
Call up data .................................................................................................................................. 169
Delete data ................................................................................................................................... 170
Transfer data to the SD card......................................................................................................... 171
New memory block ....................................................................................................................... 172
4.10 SD card........................................................................................................................................ 173
4.10.1 Display contents................................................................................................................................... 173
4.10.2 Operation ............................................................................................................................................. 174
Select SD card le ........................................................................................................................ 174
Call up data .................................................................................................................................. 175
Delete data ................................................................................................................................... 176
4.11 Historical trend............................................................................................................................. 177
4.11.1 Display contents.................................................................................................................................... 177
Page name ................................................................................................................................... 177
Digital display................................................................................................................................ 178

6TR30-G USERS MANUAL EM-8631-G Rev.16
4.11.2 Operation .............................................................................................................................................. 179
Write comment.............................................................................................................................. 179
Open event summary ................................................................................................................... 180
Open comment summary ............................................................................................................. 180
4.12 Change setting ............................................................................................................................ 181
4.12.1 Alarm threshold.................................................................................................................................... 182
4.12.2 E-mail setting ....................................................................................................................................... 184
Address list setting........................................................................................................................ 184
Report setting ............................................................................................................................... 185
4.12.3 Pen conguration ................................................................................................................................. 187
4.12.4 Reset local calibration.......................................................................................................................... 188
4.13 Maintenance ................................................................................................................................ 189
4.14 User dened screens................................................................................................................... 190
5. Unit operation 191
5.1 SD card ......................................................................................................................................... 191
SD card insertion.......................................................................................................................... 191
SD card removal ........................................................................................................................... 191
[SD CARD] lamp........................................................................................................................... 191
5.2 Recording ...................................................................................................................................... 192
Start recording .............................................................................................................................. 192
Stop recording .............................................................................................................................. 192
[RECORD] lamp ........................................................................................................................... 192
5.3 Stopping the unit ........................................................................................................................... 193
6. Maintenance 194
6.1 Maintenance using TRGCFG ........................................................................................................ 194
6.1.1 Storage and retrieval of setting values.................................................................................................... 194
Storage of the setting le .............................................................................................................. 194
Retrieval of the setting le............................................................................................................. 195
6.1.2 Maintenance........................................................................................................................................... 196
Time correction............................................................................................................................. 197
MAC address................................................................................................................................ 197
Unit version................................................................................................................................... 198
System log .................................................................................................................................... 198
Preset count.................................................................................................................................. 199
Disk usage status ......................................................................................................................... 199
Initialization................................................................................................................................... 200
FTP client test............................................................................................................................... 201
Mail report test.............................................................................................................................. 201
User dened browser view ...........................................................................................................202
6.2 Maintenance from the Web screen................................................................................................203
6.2.1 Storage and retrieval of setting values...................................................................................................203
Retrieval of the setting le.............................................................................................................203
Storage of the setting le ..............................................................................................................204
6.2.2 Maintenance ..........................................................................................................................................205
Time correction.............................................................................................................................205
System log/remote I/O status display ...........................................................................................206

7TR30-G USERS MANUAL EM-8631-G Rev.16
7. Appendix 207
7.1 Primary method of operation of the touch panel ............................................................................207
7.2 Troubleshooting ..............................................................................................................................208
7.2.1 Lamp display ..........................................................................................................................................208
7.2.2 SD card...................................................................................................................................................208
7.2.3 Web server .............................................................................................................................................208
7.2.4 TRGCFG ................................................................................................................................................209
7.2.5 LAN connection ...................................................................................................................................... 210
7.2.6 Wi-Fi connection ..................................................................................................................................... 210
7.2.7 Internet ................................................................................................................................................... 2 11
7.2.8 Error display lamp................................................................................................................................... 2 11
7.2.9 RUN contact ........................................................................................................................................... 212
7.2.10 Modbus/TCP (Master) .......................................................................................................................... 212
7.2.11 FTP server ............................................................................................................................................ 213
7.3 Reference documents .................................................................................................................... 214
7.3.1 Compatible terminals and browsers ....................................................................................................... 214
7.3.2 Web server ............................................................................................................................................. 214
7.3.3 Storing rate and sampling cycle.............................................................................................................. 215
7.3.4 SD card................................................................................................................................................... 216
7.3.5 Memory block ......................................................................................................................................... 219
7.3.6 FTP server..............................................................................................................................................220
7.3.7 Modbus/TCP slave .................................................................................................................................221
Register map ................................................................................................................................221
Internal registers...........................................................................................................................225
Commands ...................................................................................................................................230
Data range....................................................................................................................................231
7.3.8 SLMP Client............................................................................................................................................232
Request Message.........................................................................................................................232
Command list................................................................................................................................233
Command list (continued).............................................................................................................234
Command list (continued).............................................................................................................235
7.3.9 Communication volume ..........................................................................................................................236
7.3.10 Number of characters that can be displayed on each screen...............................................................236
7.3.11 FTP client..............................................................................................................................................236
7.3.12 Mail report.............................................................................................................................................237
7.3.13 Data les for user dened screen creation ...........................................................................................238
7.4 Version history................................................................................................................................242
7.4.1 Supporting signature algorithm of SSL certicate for mail server, SHA-2 ..............................................242
7.4.2 TR30-G version 1.3 revision history ........................................................................................................242
7.4.3 TR30-G version 1.4 revision history ........................................................................................................242
7.4.4 TR30-G version 1.5 revision history ........................................................................................................242
7.4.5 TR30-G version 2.0 revision history........................................................................................................243
7.4.6 TRGCFG version 2.1.20 revision history.................................................................................................243
7.4.7 TR30-G version 2.1 revision history........................................................................................................243
7.4.8 TR30-G version 2.2 revision history........................................................................................................243
7.5 Licenses ........................................................................................................................................244

8TR30-G USERS MANUAL EM-8631-G Rev.16
1. Introduction
Thank you for choosing M-System.
Before use, please check the following information.
1.1 User manual compatible versions
The versions compatible with this User Manual are as follows.
■UNIT VERSION
This User Manual is compatible with model TR30-G Unit version 2.2 or later.
Refer to the section on [Maintenance] for the method to conrm the unit version.
➔6.1.2 Maintenance ‘Unit version’
■CONFIGURATOR SOFTWARE (TRGCFG) VERSION
This User Manual is compatible with model TRGCFG version 2.2 or later.
The TRGCFG version can be conrmed using the following method.
(1) Click (or right click) on at the top left of the initial screen.
(2) Click on [About TRGCFG (A) ...] to display the version information dialog.
1. Click or right-click
2. Click
Version

9TR30-G USERS MANUAL EM-8631-G Rev.16
1.2 Precautions
■CONFORMITY WITH EU DIRECTIVES
• The equipment must be mounted inside the instrument panel of a metal enclosure.
• The actual installation environments such as panel congurations, connected devices and connected wires
may affect the protection level of this unit when it is integrated in a panel system. The user may have to
review the CE requirements in regard to the whole system and employ additional protective measures to
ensure CE conformity.
■GENERAL PRECAUTIONS
• Before you remove the unit or mount it, turn off the power supply for safety.
• The unit does not support hot insertion/removal of modules. When the unit is used in combination with R30
I/O modules, hot insertion/removal of module is not supported for R30 I/O modules.
• Before you remove the terminal block or mount it, turn off input signal for safety.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous vibration. Do not subject the unit to physical im-
pact.
• Environmental temperature must be within 0 to 50°C (32 to 122°F) with relative humidity within 10 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive cable, high frequency line, etc.).
• Do not bind these cables together with those in which noises are present. Do not install them in the same
duct.
• Max. wiring length for FE terminal should be 3 meters.
• Be sure to attach the terminal cover for safety.
■ABOUT SD CARDS
• Do not turn off the power of the unit during writing data. Insert or eject SD card according to the specied
procedure.
• Conrm the front and back side of the SD card.
■CALENDAR CLOCK
• A backup battery is employed for calendar clock IC. Backup period without power supply is approx. 2 years.
• With power on, the battery is not drained. When total power off period is approx. 2 years, the battery cannot
backup the calendar clock. The calendar clock cannot keep correct date and time.
• The battery is not replaceable by customer. When replacement is required, consult M-System.
■AND ....
• The unit is designed to function as soon as power is supplied, however, a warm up for 10 minutes is required
for satisfying complete performance described in the data sheet.
■LOGIN ID & PASSWORD
• The Login ID and password of the device are simple functions. They do not guarantee complete security.
• We recommend the user to apply own ID/password setting and not to leave the setting unused or at default
values.

10TR30-G USERS MANUAL EM-8631-G Rev.16
1.3 Component identification
■STATUS INDICATOR LED
LED COLOR FUNCTION
PWR Green ON when the power supply is on.
OFF when the power supply is off.
RUN Green ON in normal operation *1
OFF in abnormality (internal memory error, SD card error, R30 module error) *1
TR30 RUN Green
Blinking while the TR30 module is booting up.
ON after boot-up
OFF in abnormality
RECORD Green ON while logging
OFF when logging is stopped.
SD CARD Green
ON when SD card is recognized.
Blinking while accessing to the SD card.
OFF when SD card is not recognized or removed.
ERROR Red
Blinking in abnormality
(internal memory error, SD card error, R30 module error) *1
OFF in abnormality *1
*1. RUN contact output turns on in normal operation, off when the power is not supplied or in abnormality (in-
ternal memory error, SD card error, R30 module error).
Status Indicator LEDs
RJ-45 Connector
for Ethernet
Lock Tab
Specifications
Ethernet Indicator LEDs
SD Card Slot
■FRONT VIEW
■BOTTOM VIEW
■SIDE VIEW
Configuration Select SW
Logging Button
SD Button
Function Setting DIP SW
Terminal Block for
RUN Contact Output,
Power Supply
Terminal Fixing Screw
Base Fixing Screw
ON
4
3
2
1
TR30 RUN
RECORD
SD CARD
PWR
RUN
ERROR
CFG
DPX
LNK
RECORD
SD CARD
TR30
2
I/O
On
4
3
1
Configuration Connector
U
(
+
)
NC
V
(
-
)
FE
Positioning Guide
Terminal Cover

11TR30-G USERS MANUAL EM-8631-G Rev.16
■ETHERNET INDICATOR LED
LED COLOR FUNCTION
DPX Green ON during full duplex transmission
LNK Amber ON while link is established.
■CONFIGURATOR SELECT SW
SW POSITION CONFIGURATION OBJECT
TR30 Conguring the TR30 (*)
I/O Conguring the R30 series I/O modules
(*) Factory setting
■DIP SW
SW1 TR30 CONFIGURATION USB CONNECTION
OFF TRGCFG (*)
ON While checking the status by the terminal software and the TRGCFG [terminal log].
SW2 EVENT REPORTING E-MAIL
OFF Enable (*)
ON Disable
SW4 CALENDAR CLOCK BATTERY BACKUP
OFF Disable (*)
ON Enable
(*) Factory setting
Note 1: Be sure to set unused SW3 to OFF.
Note 2: In order to prevent battery drain, battery backup is at off when the TR30 is shipped from factory.
Turn it on prior to start using the unit.
■LOGGING BUTTON
Pressing and holding the button for 1 second starts and stops logging.
■SD BUTTON
Pressing and holding the button for 4 seconds turns SD CARD LED off to make the card safely removed.
■TERMINAL ASSIGNMENT
NO. ID FUNCTION
1 RUN contact output RUN contact output
2 U(+) Power supply (24 V DC)
3 V(−) Power supply (0 V DC)
4 RUN contact output RUN contact output
5 NC Not used
6 FE Functional earth
4
5
NC
FE
6
1
2
U(+)
3
V( - )

12TR30-G USERS MANUAL EM-8631-G Rev.16
2. Installation
2.1 Preparations
Other than model TR30-G logging module (referred hereafter to as “TR30,” “unit” or “device” in this manual),
model R30BS base and R30 series I/O modules, please have the following items ready.
• PC
• USB cable (USB (A) male - USB (mini B) male)
• SD card (Please see [7.3.4 SD card] for specied SD cards.)
• TR30-G congurator software (Model: TRGCFG) *1
• R30 congurator software (Model: R30CFG) *1
• User Manual for each of the above *1
*1. The software programs are available for downloading at M-System web site. ➔http://www.m-system.co.jp/
In addition, depending on the system conguration, a Wi-Fi router or a xed IP address contract is necessary.
2.2 Installation and wiring
Mount the TR30 and R30 series I/O Modules on the Base (Model: R30BS).
For details, please see the User Manual (EM-8631-A) supplied with the device and the User Manual for the I/O
modules.

13TR30-G USERS MANUAL EM-8631-G Rev.16
2.3 Preparation of configurator software
The congurator software is installed on the PC in order to congure the setting for the TR30 and each I/O
module.
2.3.1 Configurator software for the TR30: TRGCFG
Installation
Download TRGCFG from the website of M-System, and complete the installation simply by extracting it into
any folder.
Use the shortcut to TRGCFG.exe which has been extracted to the desktop as required.
TRGCFG startup
(1) Set the [Conguration Select Switch] of the device as [TR30].
(2) Turn on the power supply to the device.
(3) Connect the PC and the device using a USB cable.
When it is connected for the rst time, the driver software is automatically installed.
TR30 RUN
RECORD
SD CARD
PWR
RUN
ERROR
CFG
DPX
LNK
RECORD
SD CARD
TR30
2
I/O
On
4
3
1
U
(
+
)
NC
V
(
-
)
FE
TR30
I/O
Configuration
Select SW
Configuration
Connector

14TR30-G USERS MANUAL EM-8631-G Rev.16
(4) Start up TRGCFG, and click on the [Connect] button. The [Connect] screen is displayed.
(5) Set the radio button as [USB]. Connect to the device, select the added COM port and click on the [OK]
button.
NOTES
• If the driver software is not automatically installed, and the added COM port is not listed in
the options, please download the driver from M-System website http://www.m-system.co.jp
and install it.
• The added COM port No. varies from PC to PC.
Initial Screen
Connect
1. Click 2. Click
3. Select

15TR30-G USERS MANUAL EM-8631-G Rev.16
2.3.2 Configurator software for the I/O module: R30CFG
Installation
Please install by referring to the R30CFG User Manual.
R30CFG startup
(1) Set the [Conguration Select Switch] of the device as [I/O].
(2) Turn on the power supply to the device.
(3) Connect the PC and the device using a USB cable.
(4) Start up R30CFG, and congure the setting to use the COM port selected in TRGCFG. For details, refer to
the R30CFG User Manual.
TR30 RUN
RECORD
SD CARD
PWR
RUN
ERROR
CFG
DPX
LNK
RECORD
SD CARD
TR30
2
I/O
On
4
3
1
U
(
+
)
NC
V
(
-
)
FE
TR30
I/O
Configuration
Select SW
Configuration
Connector

16TR30-G USERS MANUAL EM-8631-G Rev.16
2.4 Explanation about the basic working and terms
Term Explanation
Channel
CH
4 types of input channels and 1 type of output channel are dened in a device. The I/O
signals are in the form of fully encoded digital data.
AI
DI
PI
OI
DO
: Analog input (16 bit signed integer, unsigned integer)
: Digital input (1 bit)
: Pulse input (32 bit unsigned integer, signed integer, oating point)
: Function input (32 bit oating point)
: Discrete output (1 bit)
The available number of channels is decided for each storing rate.
Pen To record a waveform, the channel needs to be assigned to a pen.
The available number of pens is decided for each storing rate.
Alarm zone transition
The total zone in which input values can be obtained as AI, PI or OI can be divided into
a maximum of 5 zones. The change in the zone caused by a change in the input value
is known as alarm zone transition.
In case of DI, this can only be ON/OFF, and hence a change in the input signal is
equivalent to an alarm zone transition.
Trend data Indicates the waveform data assigned to the pen and recorded.
Event data
Indicates the information that [There has been an alarm zone transition], and this infor-
mation can also be recorded along with the trend data.
When recording only event data, the channel need not be assigned to a pen.
Comment data This is a memo (text string) that the user can record at any desired position of the trend
data.
Internal memory When the TR30 records data, it records trend data, event data and comment data in the
internal nonvolatile memory of the unit. This memory is known as internal memory.
Memory block
The TR30 divides internal memory into 50 segments and manages it. Each such di-
vided segment of memory is known as a memory block.
1 memory block is equivalent to about 1 book of recorded chart paper.
In a single memory block, trend data (120 pens × 50000 points), event data (3000
events) and comment data (1000 comments) can be recorded.
Data les are transferred to the SD card per memory block.
Start new memory block Indicates that the memory block is changing during recording.
Event summary Extracted from the event data recorded in the memory block.
Comment summary Extracted from the comment data recorded in the memory block.

17TR30-G USERS MANUAL EM-8631-G Rev.16
3. Setting
3.1 Setting flow
Before starting to record using a device, follow the procedure given below to congure the setting.
Setting during initial startup
▼
Network setting
▼
System setting
▼
I/O module connection setting
▼
Remote I/O connection setting
▼
I/O setting
▼
Web server setting
▼
Record method setting
▼
Communication function setting
▼
Other setting

18TR30-G USERS MANUAL EM-8631-G Rev.16
3.2 Setting during initial startup
In order to prevent exhaustion of the battery being used for calendar IC backup in this device, the calendar
clock backup is disabled in the factory shipment setting. Hence, in its initial state, it will not work using the cor-
rect time.
If Switch 4 in the dip switch used for setting is OFF, it means that the calendar clock backup has been disa-
bled. Please correct the unit time using the procedure shown below.
(1) Set the [Conguration Select Switch] of the device as [TR30].
(2) Connect the PC in which TRGCFG is installed with the device using a USB cable, and start up TRGCFG.
(3) Click on the [Maintenance] button.
(4) If the [Conrm access mode] is displayed, check that the device is correct, and click on the [Connect] but-
ton. The [Maintenance] screen is displayed.
TR30 RUN
RECORD
SD CARD
PWR
RUN
ERROR
CFG
DPX
LNK
RECORD
SD CARD
TR30
2
I/O
On
4
3
1
U
(
+
)
NC
V
(
-
)
FE
TR30
I/O
Configuration
Select SW
Configuration
Connector

19TR30-G USERS MANUAL EM-8631-G Rev.16
(5) Click on the [Date/Time] button. The current time of the PC which is in use is initially displayed. Enter the
time to be set and click on the [Apply] button.
The time which you have set is applied in the calendar IC of the device.
(6) Next, set Switch 4 of the dip switch used for setting as ON, and enable the calendar clock battery backup.
CAUTION
If the calendar clock battery backup has been enabled, but does not start up with the correct
time, the battery may be exhausted. Please consult factory in such case.
1. Click
2. Click
3. Click
4. Click
Initial Screen
Conrm access mode
Maintenance
Date/Time
ON
4
3
2
1
TR30 RUN
RECORD
SD CARD
PWR
RUN
ERROR
CFG
DPX
LNK
RECORD
SD CARD
TR30
2
I/O
On
4
3
1
U
(
+
)
NC
V
(
-
)
FE
Function Setting DIP SW

20TR30-G USERS MANUAL EM-8631-G Rev.16
3.3 Network setting
The TR30 is equipped with Web server functions. With the help of these functions, a PC, tablet terminal or
smartphone can be used for remote monitoring.
And, setting changes can either be made via a network, or the FTP server function can be used to transfer or
delete data which is stored in the device from a PC.
There are 2 methods of connecting the TR30 via a network.
Please set appropriately to suit the usage environment.
■Connect using a local network (LAN)
This is a method in which 1 device is connected to the inhouse LAN, and monitored using a terminal connect-
ed to the same network.
■Connect via the Internet (WAN)
This is a method in which 1 device is connected to a broadband router, and remotely monitored via the Inter-
net.
TR30 PC
SD CARD
Viewer software (model: TRViewer)
■STAND-ALONE
Router
Ethernet
LAN
PC
TR30
Tablet
Router *1
Internet
(WAN)
■VIA INTERNET (WAN)
ISP
ISP
Mobile Line
*1. D.DNS service or static IP address is reguired.
Note: Data storing to SD card is performed at every transfer rate.
Wi-Fi Router
Tablet
■VIA LOCAL NETWORK (LAN)
Ethernet
PC
TR30
Hub