manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. M-system
  6. •
  7. Transmitter
  8. •
  9. M-system Mini-M M2DY User manual

M-system Mini-M M2DY User manual

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-5026 Rev.10 P. 1 / 3
INSTRUCTION MANUAL
Mini-M™
CURRENT LOOP SUPPLY MODEL M2DY
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
Signal conditioner (body + base socket).............................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■WARNING
• If equipment is not used in a manner not specified by M-
System, the protection provided by the equipment may
be impaired.
■NONINCENDIVE APPROVAL OPTION
• This equipment is suitable for use in Class I, Div. 2,
Groups A, B, C and D or Non-Hazardous Locations only.
• WARNING! Before You Remove the Unit from Its Base
Socket or Mount It, Turn Off the Power Supply and Input
Signal for Safety.
• WARNING! – Explosion Hazard –
Substitution of Components May Impair Suitability for
Class I, Div. 2.
• WARNING! – Explosion Hazard –
Do Not Disconnect Equipment Unless Power Has Been
Switched Off or The Area is Known To Be Non-Hazardous.
• The equipment was evaluated for use in the ambient tem-
perature and relative humidity as mentioned in ‘ENVI-
RONMENT’ section.
• The input and output wiring must be in accordance with
Class I, Div. 2 wiring methods and in accordance with the
authority having jurisdiction for use in these hazardous
locations.
■CONFORMITY WITH EU DIRECTIVES OR UL
• The equipment must be mounted inside a panel.
• The actual installation environments such as panel con-
figurations, connected devices, connected wires, may affect
the protection level of this unit when it is integrated in
a panel system. The user may have to review the CE re-
quirements in regard to the whole system and employ ad-
ditional protective measures* to ensure the CE conformity.
* For example, installation of noise filters and clamp fil-
ters for the power source, input and output connected
to the unit, etc.
• Install lightning surge protectors for those wires connect-
ed to remote locations.
■POWER INPUT RATING & OPERATIONAL RANGE
• Locate the power input rating marked on the product and
confirm its operational range as indicated below:
85 – 264V AC rating: 85 – 264V, 47 – 66 Hz, approx. 3 – 5VA
24V DC rating: 24V ±10%, approx. 3W
11 – 27V DC rating: 11 – 27V, approx. 3W
110V DC rating: 85 – 150V, approx. 3W
■GENERAL PRECAUTIONS
• Before you remove the unit from its base socket or mount
it, turn off the power supply and input signal for safety.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -5 to +55°C
(23 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
• Be sure that the ventilation slits are not covered with ca-
bles, etc.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
• With voltage output, do not leave the output terminals
shortcircuited for a long time. The unit is designed to
endure it without breakdown, however, it may shorten ap-
propriate life duration.
COMPONENT IDENTIFICATION
Model
SPAN
ZERO
Zero Adj.
Span Adj.
Body Base Socket
Connection
Diagram
Specifications
Fixing Screw
M2DY
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-5026 Rev.10 P. 2 / 3
INSTALLATION
Loosen the fixing screw at the front of the unit in order to
separate the body from the base socket.
DIN Rail
35mm wide
Spring Loaded
DIN Rail Adaptor
■DIN RAIL MOUNTING
Set the base socket so that
its DIN rail adaptor is at
the bottom. Position the
upper hook at the rear side
of base socket on the DIN
rail and push in the lower.
When removing the socket,
push down the DIN rail
adaptor utilizing a minus
screwdriver and pull.
■WALL MOUNTING
Refer to “EXTERNAL DIMENSIONS.”
TERMINAL CONNECTIONS
Connect the unit as in the diagram below or refer to the connection diagram on the side of the unit.
■EXTERNAL DIMENSIONS unit: mm (inch)
5
9
21.5 (.85)
70.5 (2.78)
84 (3.31)10 (.39) 15 (.59)
6 (.23)
59 (2.32)
DIN RAIL
35mm wide
[4 (.16)]
8–M3
SCREW
72 (2.83)
23 (.91)
2–4.2x5
(.17x.20)
MTG HOLE
6 (.24) deep
114 (4.49)
• When mounting, no extra space is needed between units.
4
8
12
14 13
1
4 (.16)
■CONNECTION DIAGRAM
5
+
–
+
–
4
8
1
–
+
MONITOR
(1 – 5V DC)
V
+
–
OUTPUT
9
12
U(+)
V(–)
POWER
13
14
2-WIRE
TRANSMITTER
WIRING INSTRUCTIONS
■SCREW TERMINAL
Torque: 0.8 N·m
■SOLDERLESS TERMINAL
Refer to the drawing below for recommended ring tongue
terminal size. Spade tongue type is also applicable.
Applicable wire size: 0.25 to 1.65 mm2(AWG 22 to 16)
Recommended manufacturer: Japan Solderless Terminal
MFG.Co.Ltd, Nichifu Co.,ltd
6 (.24) max
3.3 (.13) max
mm (inch)
M2DY
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-5026 Rev.10 P. 3 / 3
CHECKING
1) Terminal wiring: Check that all cables are correctly con-
nected according to the connection diagram.
2) Power input voltage: Check voltage across the terminal
13 – 14 with a multimeter.
3) Input: Check that the input signal is within 0 – 100% of
the full-scale.
4) Output: Check that the load resistance meets the de-
scribed specifications.
ADJUSTMENT PROCEDURE
This unit is calibrated at the factory to meet the ordered
specifications, therefore you usually do not need any cali-
bration.
For matching the signal to a receiving instrument or in case
of regular calibration, adjust the output as explained in the
following.
■HOW TO CALIBRATE THE OUTPUT SIGNAL
Use a signal source and measuring instruments of sufficient
accuracy level. Turn the power supply on and warm up for
more than 10 minutes.
1) ZERO: Apply 0% input and adjust output to 0%.
2) SPAN: Apply 100% input and adjust output to 100%.
3) Check ZERO adjustment again with 0% input.
4) When ZERO value is changed, repeat the above proce-
dure 1) – 3).
MAINTENANCE
Regular calibration procedure is explained below:
■CALIBRATION
Warm up the unit for at least 10 minutes. Apply 0%, 25%,
50%, 75% and 100% input signal. Check that the output
signal for the respective input signal remains within accu-
racy described in the data sheet. When the output is out of
tolerance, recalibrate the unit according to the “ADJUST-
MENT PROCEDURE” explained earlier.
LIGHTNING SURGE PROTECTION
M-System offers a series of lightning surge protector for
protection against induced lightning surges. Please contact
M-System to choose appropriate models.

Other M-system Transmitter manuals

M-system Mini-M M2TG User manual

M-system

M-system Mini-M M2TG User manual

M-system 27PM User manual

M-system

M-system 27PM User manual

M-system Mini-M M2EXR User manual

M-system

M-system Mini-M M2EXR User manual

M-system B5RS User manual

M-system

M-system B5RS User manual

M-system LC2 User manual

M-system

M-system LC2 User manual

M-system 10AC User manual

M-system

M-system 10AC User manual

M-system M3LLC User manual

M-system

M-system M3LLC User manual

M-system W2VABS User manual

M-system

M-system W2VABS User manual

M-system M5YV User manual

M-system

M-system M5YV User manual

M-system KVS User manual

M-system

M-system KVS User manual

M-system Mini-M M2CEC User manual

M-system

M-system Mini-M M2CEC User manual

M-system 10JR User manual

M-system

M-system 10JR User manual

M-system Mini-M M2UDS User manual

M-system

M-system Mini-M M2UDS User manual

M-system B3HU2 User manual

M-system

M-system B3HU2 User manual

M-system Mini-M M2AC User manual

M-system

M-system Mini-M M2AC User manual

M-system M1EXS-2 User manual

M-system

M-system M1EXS-2 User manual

M-system B3HU User manual

M-system

M-system B3HU User manual

M-system 27U User manual

M-system

M-system 27U User manual

M-system 10VK User manual

M-system

M-system 10VK User manual

M-system Mini-M M2XR2 User manual

M-system

M-system Mini-M M2XR2 User manual

M-system Mini-M M2WVS User manual

M-system

M-system Mini-M M2WVS User manual

M-system 10JFT User manual

M-system

M-system 10JFT User manual

M-system Mini-M M2RS1 User manual

M-system

M-system Mini-M M2RS1 User manual

M-system TM User manual

M-system

M-system TM User manual

Popular Transmitter manuals by other brands

Endress+Hauser iTEMP TMT82 operating instructions

Endress+Hauser

Endress+Hauser iTEMP TMT82 operating instructions

Technics RAK-SA614MH How to use

Technics

Technics RAK-SA614MH How to use

Vivax vScan User handbook

Vivax

Vivax vScan User handbook

HETRONIC NOVA-M quick reference

HETRONIC

HETRONIC NOVA-M quick reference

Honeywell Midas S2 user manual

Honeywell

Honeywell Midas S2 user manual

RHEONIK RHE28 Installation & start?up guide

RHEONIK

RHEONIK RHE28 Installation & start?up guide

ARG ARG-TX72BP Manual and user guide

ARG

ARG ARG-TX72BP Manual and user guide

JUMO dTRANS T01 HART operating instructions

JUMO

JUMO dTRANS T01 HART operating instructions

Burkert 8325 operating instructions

Burkert

Burkert 8325 operating instructions

Crestron DigitalMedia DM-TX-200-2G Operations & installation guide

Crestron

Crestron DigitalMedia DM-TX-200-2G Operations & installation guide

Intelix DIGI‐HD‐IR2 installation manual

Intelix

Intelix DIGI‐HD‐IR2 installation manual

Siemens SITRANS L Series Compact operating instructions

Siemens

Siemens SITRANS L Series Compact operating instructions

Elenos ETG5200 manual

Elenos

Elenos ETG5200 manual

Moseley DSP6000A user manual

Moseley

Moseley DSP6000A user manual

AFi MT-388SL instruction manual

AFi

AFi MT-388SL instruction manual

impact VC-500WLXMT instructions

impact

impact VC-500WLXMT instructions

PNI VALENTINE V880 user manual

PNI

PNI VALENTINE V880 user manual

Intercoax Ipify ECP-2704R-4T-PKG Quick install guide

Intercoax

Intercoax Ipify ECP-2704R-4T-PKG Quick install guide

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.