M2I TOPRT-Ex Series User manual

Industrial HMI Touch Panel Hardware Manual
M2I Corporation 1 / 23
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea,
Tel: [phone], Fax: [phone], www.m2i.co.kr
Thank you for purchasing the industrial HMI touch panel series of M2I corporation.
Please read this manual carefully to know installing, wiring, operating this equipment for safe use of this
product.
M2I Corporation
Industrial HMI Touch Panel
TOPRT -Ex Series
Hardware Manual

Industrial HMI Touch Panel Hardware Manual
M2I Corporation 2 / 23
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea,
Tel: [phone], Fax: [phone], www.m2i.co.kr
Index
Index .................................................................................................................................................................................................................. 2
Chapter 1 Safety Precautions................................................................................................................................................................. 3
Chapter 2 Overview.................................................................................................................................................................................... 5
2.1 Introduction of Products.............................................................................................................................................. 5
2.2 Package Contents............................................................................................................................................................ 5
2.3 Explanation of Model name ....................................................................................................................................... 6
Chapter 3 General Specifications......................................................................................................................................................... 6
3.1 Electrical Specifications................................................................................................................................................. 6
3.2 Display Specifications .................................................................................................................................................... 7
3.3 Touch Specifications....................................................................................................................................................... 7
3.4 Sub Function Specifications (*Premium models only) ................................................................................... 7
3.5 Memory Specifications.................................................................................................................................................. 7
3.6 Environment Specifications......................................................................................................................................... 7
3.7 Structure Specifications ................................................................................................................................................ 7
Chapter 4 Part Names and General Specifications...................................................................................................................... 8
4.1 TOPRT1210SD-Ex............................................................................................................................................................. 8
4.2 TOPRT1230XD-Ex / TOPRT1240XD-Ex................................................................................................................... 9
4.3 TOPRT12-Ex Series-Rear Part Names and Specifications ...........................................................................11
4.4 TOPRT12-Ex Series- Side Part Names and Specifications..........................................................................11
4.5 TOPRT12-Ex Series- Top Part Names and Specifications...........................................................................11
4.6 TOPRT12-Ex Series- Bottom Part Names and Specifications ...................................................................12
Chapter 5 External Device Interface..................................................................................................................................................12
5.1 Serial Interface ................................................................................................................................................................12
5.2 Ethernet Communication Specifications .............................................................................................................13
5.3 USB Interface ...................................................................................................................................................................14
Chapter 6 Installation...............................................................................................................................................................................15
6.1 Installation Requirement ............................................................................................................................................15
6.2 TOPRP Assemble............................................................................................................................................................15
6.3 Installation Procedure..................................................................................................................................................16
6.4 Front USB...........................................................................................................................................................................18
Chapter 7 Wiring........................................................................................................................................................................................18
7.1 Power wiring ....................................................................................................................................................................18
7.2 Ground wiring .................................................................................................................................................................19
7.3 Cable Clamp Installation ............................................................................................................................................20
Chapter 8 Maintenance ..........................................................................................................................................................................21
8.1 Cleaning the Display ....................................................................................................................................................21
8.2 Periodic Check Points..................................................................................................................................................21
8.3 Problems with the Device..........................................................................................................................................21
8.4 Setting System Recovery Mode..............................................................................................................................21
Chapter 9 Product and Warning Label............................................................................................................................................22
Chapter 10 Product Label......................................................................................................................................................................23

Industrial HMI Touch Panel Hardware Manual
M2I Corporation 3 / 23
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea,
Tel: [phone], Fax: [phone], www.m2i.co.kr
Chapter 1 Safety Precautions
■Before using the product
To use the product safely and effectively, please read the contents of this manual thoroughly before use. Please
keep to the safety precaution, for it is to prevent accidents and potential danger from occurring. Safety precaution
is classified into ‘Warning’ and ‘Caution’ and their meanings are as follows. Also the indicated illustrations on the
product and in the manual have the following meanings.
Violating the instruction may result in serious personal injury or death.
Violating the instruction may result in slight personal injury or product damage.
Be cautious, for danger may be present.
Be cautious, for there is a possibility of an electric shock.
■Anti-Explosion Precautions
Do not open the product when explosive gas is around.
All cables connected with the product should not be connected or disconnected when the power of product
is on.
Do not change SD Card when the power is connected to product.
■General Precautions
Do not press the screen with a hard or sharp object (awl, screwdriver, pen) with too strong a force.
It may cause malfunction of touch due to damage of the front sheet.
Do not use or store in an environment with high vibration.
Do not allow foreign objects such as water, liquids, or metal powders to enter the product. This may cause
breakage or electric shock.
Use the radio or mobile phone at least 30cm away from the main unit.
Two or fewer bright spots may appear on the LCD screen, and certain areas may appear brighter, but this is
not a defect in LCD characteristics.
Do not store or operate in direct sunlight. Direct sunlight can change the properties of the LCD.
■Design Precautions
Install protection circuit on the outside of Products to protect the entire control system when external power
supply or Products have problems.
As the malfunction & incorrect result of Products could damage the stability of the entire systems and human
body, you must install damage preventing interlock circuit such as emergency stop, Protective circuits,
positioning upper and lower limit switch and interlock for forward/reverse operation.
When a computer or other controllers communicate and exchange data with products or change operation
mode of products, set up protective sequence program in PC or Controller for protecting system from
communication error.
The output signal or communication lines should be separated from the power line or high tension wire.
They should be installed 100mm (3.94 Inch) or more from each other.

Industrial HMI Touch Panel Hardware Manual
M2I Corporation 4 / 23
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea,
Tel: [phone], Fax: [phone], www.m2i.co.kr
■Wiring Precautions
Be sure the wiring is done correctly by checking the product’s rated voltage and the terminal layout. Incorrect
wiring could result in fire, damage or malfunctions.
Tighten the terminal screw with the specified torque. If the screws of terminal are loose, it could result in
short circuit, fire, malfunctions.
FG Terminal must be used a dedicated ground. Not doing so could result in malfunctions.
a. Grounding should be the Class 3 grounding. The cable for grounding should be more than 2㎟.
b. grounding point be closed to the products and make short the distance to the ground cable if possible.
Please see below.
■Installation Precaution
Do not install the location which exceeds allowed temperature. Product can be damaged or shorten the life.
Especially Install environment as below should be avoided.
Do not Install product to the place which the ambient temperature is out of limits, from -10℃ to 50℃ or on
the surface of control board which high pressure equipment is installed.
Do not install to the place where strong shock or vibration continuously have impacted on product.
For indoor use only.
Use the product under 2000M altitude.
The length of the power cable must be no more than 3 m (10 feet).
■Disposal Precaution
When you dispose of product and battery, please treat it as industrial waste. It can create poisonous substances
or explosion.
■Battery Specification
Mounted on mainboard Model CTL920F Battery is not replaced by the user. If the battery has run out of service,
please contact our Customer Support Center for replacement and inspection.
Item
Content
Battery Voltage
DC 2.3V , 7.7mAh
Battery Model
CTL920F (lithium Rechargeable / non-exchangeable )
Battery Lifetime
Permanent (In case of ambient temperature 25℃)
*The specifications are subject to change depending on the model.
■All field-wiring connections to this unit shall be from Limited Voltage / Limited Current, below 20~28 Vdc
isolated secondary source with an output fuse, or Class 2 secondary circuits.

Industrial HMI Touch Panel Hardware Manual
M2I Corporation 5 / 23
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea,
Tel: [phone], Fax: [phone], www.m2i.co.kr
Chapter 2 Overview
2.1 Introduction of Products
This industrial HMI touch panel is an industrial control device required in industrial field. It is a device based on
RS-232C and RS-422/485, Ethernet which is used for the basic purpose of communication with another device
(PLC).
2.2 Package Contents
The components of the product are as follows.
Before using the product, please check that all of the following components are included.
Item
Figure
Quantity
Product and User Manual
1
Gasket
1
Mounting Clamp
10
Power Connector and COM3
communication connector
1
USB Cable Clamp
Cable Tie
1
Accessories
(Sold separate)
USB Memory
USB Cable
SD Card
Front Protect Sheet
User Option

Industrial HMI Touch Panel Hardware Manual
M2I Corporation 6 / 23
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea,
Tel: [phone], Fax: [phone], www.m2i.co.kr
2.3 Explanation of Model name
TOPR
T
□□
□□
□
□
-
Ex
□□
Series
Type
Screen
Option
Resolution
Power
-
Anti-Explosion
Reserve
P: Process
08: 8.4"
10: TOPRP10D
+ TOPRD **10*
Q: QVGA(320*240)
D: DC
Ex:: Explosion proof or
special model
Customer option:
No relate to anti-
explosion
D: Display
10: 10.4"
20: TOPRP10D
+ TOPRD **20*
V: VGA(640*480)
A: AC
Blank: Non-explosion
proof or general model
T: P + D
12: 12.1"
30: TOPRP10D
+ TOPRD **30*
S: XGA(800*600)
15: 15.0"
40: TOPRP50D
+ TOPRD **30*
X: XGA(1024*768)
* EX model of
1210" has "S" for
XGA
** TOPRT1210SD-Ex is combined by TOPRP10D and TOPRD1220X.
2.3.1 Process Module (Main Unit)
TOPR
P
□□
□
Series
Type
Option
Power
P: Process
10: Standard
D: DC
T: P + D
50: Standard(10) + Performance improvement
2.3.2 Display Module (Accessory Unit)
TOPR
D
□□
□□
□
Series
Type
Screen
Option
Resolution
D: Display
08: 8.4”
10: Standard
Q: QVGA(320*240)
10:10.4"
20: Premium
V: VGA(640*480)
12: 12.1”
30: "20" Premium + Added Function/Option
S: SVGA(800*600)
15: 15.0”
X: XGA(1024*768)
Chapter 3 General Specifications
3.1 Electrical Specifications
Rated voltage
Powered by Process
12V, 3.3V
Power
Consumption
Process Module
TOPRP10D
9W or less
TOPRP50D
Display Module
TOPRD1220X
6W or less
TOPRD1230X
9W or less
TOPRT1210SD-Ex (TOPRP10D + TOPRD1220X)
15W or less
TOPRT1230XD-Ex (TOPRP10D + TOPRD1230X)
18W or less
TOPRT1240XD-Ex (TOPRP50D + TOPRD1230X)
18W or less

Industrial HMI Touch Panel Hardware Manual
M2I Corporation 7 / 23
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea,
Tel: [phone], Fax: [phone], www.m2i.co.kr
3.2 Display Specifications
Color
16M Colors
Brightness Level
10 Level(by software)
Backlight Type
LED
Backlight Life
50,000 hours
Display Font
MS Windows Vector font possible Image font
Front LED Indicate
Built in
3.3 Touch Specifications
Part
Specification
Model
Touch Type
Built-in, Analog resistive touch sensor
TOPRT ** 10 /30/ 40
3.4 Sub Function Specifications (*Premium models only)
Part
Specification
Model
Front Camera
Built-in, Resolution: VGA(640*480)
TOPRT ** 10 / 30 / 40
Proximity Sensor
Built-in, Sensing Distance 0.7M
TOPRT ** 10 / 30 / 40
Brightness Sensor
Built-in, Brightness controls automatically as 10 level
TOPRT ** 10 / 30 / 40
IrDA
Built-in, 0.7M, Exclusive products only
TOPRT ** 30 / 40
3.5 Memory Specifications
Screen Memory
128MB
Backup Memory
512KB: System buffer(10K Word),Including Alarm/Log/Recipe
Backup Period
Permanent
Real Time Clock
Built in(by Battery)
3.6 Environment Specifications
Operation Temperature(℃)
-10 ~ +50
Storage Temperature(℃)
-20 ~ +60
Operation Humidity(%RH)
0 ~ 90(No dew)
Atmosphere
No corrosive gas
Protection Classification
Front IP54, Rear IP2X)
3.7 Structure Specifications
Cooling System
Natural air circulation
Case Material
AL(Aluminum)

Industrial HMI Touch Panel Hardware Manual
M2I Corporation 8 / 23
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea,
Tel: [phone], Fax: [phone], www.m2i.co.kr
Chapter 4 Part Names and General Specifications
4.1 TOPRT1210SD-Ex
4.1.1 TOPRT1210SD-Ex External Dimension
Product
A(mm)
B(mm)
C(mm)
D(mm)
TOPRT1210SD-Ex
320
261
5
66.5

Industrial HMI Touch Panel Hardware Manual
M2I Corporation 9 / 23
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea,
Tel: [phone], Fax: [phone], www.m2i.co.kr
4.1.2 TOPRT1210SD-Ex Front Part Names and Specifications
No.
Part
Description
Support Model
①
Power LED
System Power Status LED
Common
②
Proximity Sensor
Automatically backlight ON/OFF by sensing object coming
Option
③
Brightness Sensor
Automatically brightness controls by ambient brightness
Option
④
USB OTG
UP/Down load project file
Common
⑤
Camera
Resolution VGA(640*480)
Option
⑥
LCD Panel
TFT 16M Color LCD
Common
⑦
Touch Panel
Analog resistive touch sensor
Common
⑧
USB OTG Cover
Front USB OTG cover hole
Common
4.2 TOPRT1230XD-Ex / TOPRT1240XD-Ex

Industrial HMI Touch Panel Hardware Manual
M2I Corporation 10 / 23
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea,
Tel: [phone], Fax: [phone], www.m2i.co.kr
4.2.1 TOPRT1230XD-Ex / TOPRT1240XD-Ex External Dimension
Product
A(mm)
B(mm)
C(mm)
D(mm)
TOPRT1230XD-Ex
320
261
5
66.5
TOPRT1240XD-Ex
320
261
5
66.5
4.2.2 TOPRT1230XD-Ex / TOPRT1240XD-Ex Front Part Names and Specifications
No.
Part
Description
Support Model
①
Power LED
System power status LED
Common
②
Proximity Sensor
Automatically backlight ON/OFF by sensing object coming
Common
③
IR Sensor
Device for communication with dedicated equipment
Common
④
Brightness Sensor
Automatically brightness controls by ambient brightness
Common
⑤
Camera
Resolution VGA (640*480)
Option
⑥
LCD Panel
TFT 16M Color LCD
Common
⑦
Touch Panel
Analog / Capacitive resistive touch sensor
Option
⑧
USB Cover
Front USB cover hole
Common
⑨
USB OTG
Program upload or download
Common