MadgeTech RHTemp2000 User manual

MadgeTech, Inc.
PO Box 50 lWarner, NH 03278
Phone [phone] lFax 603.456.2012
www.madgetech.com l[email protected]
Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289
REV A 2008.07.08
To view the full MadgeTech product line,
visit our website at www.madgetech.com.
Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289
Product Information Card
RHTemp2000
RHTemp2000
Temperature and Humidity Recorder with LCD
Product Quick Reference Card
Part Number RHTemp2000
Temperature Sensor Semiconductor
Temperature Range –20 to +60°C
Temperature Resolution 0.1°C
Calibrated Accuracy +0.5°C (0 to 50°C)
Humidity Sensor Internal Semiconductor
Humidity Range 0 to 95%RH
Humidity Resolution 0.1%RH
Humidity Accuracy +3%RH (+2%RH @ 25°C Typical)
Memory 131,071/channel
Sample Rate 2 seconds to 24 hours
Required Interface Package IFC110 or IFC200
Baud Rate 115,200
Typical Battery Life 1 year with display off, 30 days with
continuous LCD and no backlight
Operating Environment –20 to +60°C, 0 to 95%RH (non-condensing)
Material Black Anodized Aluminum
Dimensions 4.8” x 3.3” x 1.25” (112mm x 84mm x 32mm)
Approvals CE
Specifications subject to change.
See MadgeTech’s terms and conditions at www.madgetech.com
Device Maintenance
Battery Replacement
Materials:
3/32” HEX Driver (Allen Key)
Replacement Battery (U9VL-J)
- Remove the cover from the device by unscrewing the four
screws.
- Remove the battery from its compartment and unsnap it
from the connector.
- Snap the new battery into the terminals and verify it is secure.
- Replace the cover taking care not to pinch the wires. Screw
the enclosure back together securely.
Note: Be sure not to over tighten the screws or strip the threads.
Battery Warning
WARNING: FIRE, EXPLOSION, AND SEVERE BURN HAZARD. DO NOT
SHORT CIRCUIT, CHARGE, FORCE OVER DISCHARGE, DISASSEMBLE,
CRUSH, PENETRATE OR INCINERATE. BATTERY MAY LEAK OR
EXPLODE IF HEATED ABOVE 60°C (140°F).
Recalibration
The RHTemp2000 standard calibration is one point at 25°C and
two points at 25%RH and 75%RH.
Pricing:
Recalibration traceable to NIST $90.00
Recalibration $70.00
Additional:
As Found Data $15.00
Additional Points $15.00 per point
To send the devices back, visit www.madgetech.com, select Services
then RMA Process.

RHTemp2000 Product Quick Reference Card
Product Notes
Backlight
The backlight uses a significant amount of battery life. Refer to
the manual to configure the auto shut-off when not in use.
Password Protection
An optional password may be programmed into the device to
restrict access to configuration options.
Note: For additional instructions refer to your “Data Logger &
Software Operating Manual”.
Installation Guide
Installing the Interface cable
- IFC200, IFC202 or IFC300
Refer to the “Quick Start Guide” included in the package.
- IFC110, IFC102 or IFC103
Plug the serial cable into the port and verify it is secure.
- USB-1 or USB-101
Install the USB drivers from the CD provided in the kit, than
plug the USB cable into the computer and the serial cable into
the serial port.
Installing the software
Insert the Software CD in the CD-ROM Drive. If the autorun
does not appear, locate the drive on the computer and double
click on Autorun.exe. Follow the instructions provided in the
Wizard.
Connecting the data logger
- Once the software is installed and running, plug the interface
cable into the data logger.
- Click the Communication Menu, then Auto Configure Port.
- After a moment, a box similar to the following will appear;
- Click OK. The Device Status box will appear. Click OK.
- At this point, communications have been configured for your
logger. These settings can be found under the Communication
Menu.
Note: For additional installation instructions refer to your “Data
Logger & Software Operating Manual”.
Device Operation
Starting the data logger
- Click Device Menu then Start Device.
- Choose the desired start
method.
- Choose the desired stop
method.
- Choose the start parameters
by selecting a Reading Rate
suitable for the application.
- Enter in any other desired
parameters and click Start.
- A box will appear stating
the data logger has been
started. Click OK.
- Disconnect the data logger from the interface cable and
place it in the environment to measure.
Note: The device will stop recording data when the end of
memory is reached or the device is stopped. At this point the
device cannot be restarted until it has been re-armed by the
computer.
Downloading data from a data logger
- Connect the data logger to the interface cable.
- Click the Device Menu then Read Device Data. This will
offload all recorded data onto the PC.
Technical Support
Visit www.madgetech.com, or call [phone].
Technical support is also available by e-mailing
[email protected]
Additional product information is available by e-mailing
[email protected].