MadgeTech RHTemp101 User manual

MadgeTech, Inc.
PO Box 50 lWarner, NH 03278
Phone [phone] lFax 603.456.2012
www.madgetech.com l[email protected]
Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289
REV A 2008.07.08
To view the full MadgeTech product line,
visit our website at www.madgetech.com.
Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289
Product Information Card
RHTemp101 and RHTemp110 and
TempRetrieverRH
RHTemp110
Temperature and Humidity Recorder with 10 Year Battery Life
RHTemp101
Temperature and Humidity Recorder
Product Quick Reference Card
TempRetrieverRH
Temperature and Humidity Recorder with Pushbutton Start/Stop
Specication RHTemp101 RHTemp110 TempRetrieverRH
Temperature Sensor Internal semiconductor Internal semiconductor Internal semiconductor
Temperature Range –40 to +80°C –40 to +80°C -40 to +80°C
Temperature Resolution 0.1°C 0.1°C 0.1°C
Calibrated Accuracy +0.5°C +0.5°C +0.5°C
Humidity Sensor Internal semiconductor Internal semiconductor Semiconductor
Humidity Range 0 to 95%RH 0 to 95%RH 0 to 95%RH
Humidity Resolution 0.5%RH 0.5%RH 0.1%RH
Calibrated Accuracy +3.0%RH +3.0%RH +3.0%RH
Memory 21,845/channel 21,845/channel 16,383/channel
Sample Rate 2 seconds to 12 hours 2 seconds to 12 hours 5 seconds to 30 min.
LED Indicator Red Red Red & Green
RH Units %RH, dew pt., water vapor concentration (mg/ml)
Alarm Temperature No Temperature
Required Interface Package IFC110 or IFC200 IFC110 or IFC200 IFC110 or IFC200
Baud Rate 2,400 57,600 38,400
Typical Battery Life 1 year 10 years 1 year
Operating Environment –40 to +80°C, 0 to 95%RH (Non–Condensing)
Material ABS plastic ABS plastic ABS plastic
Dimensions 1.4” x 2.2” x 0.6”
(36mm x 56mm x 16mm)
1.7” x 2.3” x 0.8”
(44mm x 59mm x 21mm)
1.4” x 2.2” x 0.6”
(36mm x 56mm x 16mm)
Approvals CE CE CE
Specifications subject to change.
See MadgeTech’s terms and conditions at www.madgetech.com
Device Maintenance
Battery Replacement
Materials:
Small Phillips Head Screwdriver
Replacement Battery (LTC-7PN)
- Puncture the center of the back label with the screw driver
and unscrew the enclosure.
- Remove the battery by pulling it perpendicular to the circuit
board.
- Insert the new battery into the terminals and verify it is secure.
- Screw the enclosure back together securely.
Note: Be sure not to over tighten the screws or strip the threads.
Battery Warning
WARNING: FIRE, EXPLOSION, AND SEVERE BURN HAZARD. DO NOT
SHORT CIRCUIT, CHARGE, FORCE OVER DISCHARGE, DISASSEMBLE,
CRUSH, PENETRATE OR INCINERATE. BATTERY MAY LEAK OR
EXPLODE IF HEATED ABOVE 80°C (176°F).
Recalibration
The RHTemp101, RHTemp110 and TempRetrieverRH standard
calibration is one point at 25°C and two points at 25%RH and
75%RH.
Pricing:
Recalibration traceable to NIST $90.00
Recalibration $70.00
Additional:
As Found Data $15.00
Additional Points $15.00 per point
To send the devices back, visit www.madgetech.com, select Services
then RMA Process.

RHTemp101, RHTemp110 and TempRetrieverRH Product Quick Reference Card
Product Notes
LEDs
Once started, the LED will flash at the selected reading rate to
indicate that the device is running. The LED will flash in one
second intervals if there is an alarm condition.
Alarm Settings
To change the settings for the temperature alarm;
- Select Alarm Settings from the Device menu in the MadgeTech
software. A window will appear allowing the customer to set the
high and low temperature alarms.
- Press Change to edit the values.
- Check Enable Alarm Settings to enable the feature. The values
can be entered in the field manually or by using the scroll bars.
- Click Save to save the changes. To clean an active alarm, press
Clear Alarm.
Installation Guide
Installing the Interface cable
- IFC200, IFC202 or IFC300
Refer to the “Quick Start Guide” included in the package.
- IFC110, IFC102 or IFC103
Plug the serial cable into the port and verify it is secure.
- USB-1 or USB-101
Install the USB drivers from the CD provided in the kit, than
plug the USB cable into the computer and the serial cable into
the serial port.
Installing the software
Insert the Software CD in the CD-ROM Drive. If the autorun
does not appear, locate the drive on the computer and double
click on Autorun.exe. Follow the instructions provided in the
Wizard.
Connecting the data logger
- Once the software is installed and running, plug the interface
cable into the data logger.
- Click the Communication Menu, then Auto Configure Port.
- After a moment, a box similar to the following will appear;
- Click OK. The Device Status box will appear. Click OK.
- At this point, communications have been configured for your
logger. These settings can be found under the Communication
Menu.
Note: For additional installation instructions refer to your “Data
Logger & Software Operating Manual”.
Device Operation
Starting the data logger
- Click Device Menu then
Start Device.
- Choose the desired start
method.
- Choose the start parameters
by selecting a Reading Rate
suitable for your application.
- Enter in any other desired
parameters and click Start.
- A box will appear stating the
data logger has been started.
Click OK.
- Disconnect the data logger from the interface cable and
place it in the environment to measure.
Note: The device will stop recording data when the end of
memory is reached or the device is stopped. At this point the
device cannot be restarted until it has been re-armed by the
computer.
Downloading data from a data logger
- Connect the data logger to the interface cable.
- Click the Device Menu then Read Device Data. This will
offload all recorded data onto the PC.
Technical Support
Visit www.madgetech.com, or call [phone].
Technical support is also available by e-mailing
[email protected]
Additional product information is available by e-mailing
[email protected].