MadStad Engineering GL1800 User manual

Please read this entire manual before proceeding with installation.
What is in the box:
(1) Set of preassembled MadStad
adjustable windshield brackets
(1) Gloss black mounting plate
(4) M6 x 16 mounting screws
(4) M6 flat washers
(4) M6 lock nuts
Windshield Screws:
(4) M5 x 20 Phillips truss screws
(4) M5 plastic washers
(4) M5 soft rubber washers
Tools Needed:
- 4 mm Allen wrench (hex key)
- 10 mm wrench (open-end, box, or small adjustable crescent)
- #2 Phillips screwdriver
Adjustable Windshield System
Honda Gold Wing GL1800 / GL1500
(Actual brackets may be slightly
different than shown here.)

MadStad adjustable brackets are designed to bolt to a curved surface like the
adapter plate included in this kit. The new windshield attaches to the top of the
brackets with M5 Philips truss screws. Loosening the two adjustment knobs
allow you to change the windshield height and tilt without getting off of the
bike, and without any tools.
You will need to remove your factory windshield; it is not adaptable for use
with these brackets.
Bracket Installation:
Your MadStad brackets attach to the mounting plate as shown on page 3. Use the
four M6 x 16 screws with washers and lock nuts as shown in the diagram below.

The knobs on the brackets go to the insides (facing each other) with the knob
sides up. When both brackets are installed it should look like the diagram below:
The mounting plate then slides into the fairing in place of the stock shield and
screws down with the original factory windshield screws. Leave the factory
adjustment levers and strap loose while you do this.
NOTE: Our plate is NOT designed to sit all the way at the bottom of the Honda
factory windshield sliding range. This is because the nuts that hold our brackets
to our plate need to sit ABOVE the fairing, not on it or below it. Please be aware
of this and position our plate accordingly before tightening it down. You will not
need to use the factory adjustment anyway because our brackets have more range
and more capability than the factory adjustment system. Once the mounting plate
is screwed into the sliding factory sliding nuts in the fairing, you can clamp it
down in place using the factory levers. The clamping strap tension may need to
be adjusted.

Adjusting the Brackets
The knob screws release the brackets allowing the windshield to slide and tilt.
These knob screws must always be tightened securely before riding. DO NOT
attempt to adjust the brackets while riding! You must come to a complete stop
before making adjustments. Also make sure that you do not set the windshield
in such a way that causes your handlebars or hand guards (if installed) to hit the
windshield when turning, or before reaching full lock.
To make adjustments, loosen the knobs 1-2 turns and set the windshield so the
top edge is at about your chin level as you look straight ahead while seated on
the bike. Set the angle at approximately 60 degrees. (Use the angle guide on the
back page of this manual as a guide.) Tighten the knobs and go for a ride to see
if you now have smooth airflow over and around your helmet. Do this on a
calm day if at all possible; windy days make it hard to judge the airflow. Don’t
ever try to adjust the mount while in motion!
WARNING: If you tilt the shield fully backward, it may make contact with the
top edge of the brackets. This could scratch the back of your shield, so please
check to make sure there is no contact.
To try a different windshield position, bring the motorcycle to a complete stop
and out of traffic. Loosen the two knob screws and tilt the windshield forward
or back 2-3 degrees or so, and/or adjust it up or down if necessary. Re-tighten
the knobs and go for another ride.
Continue experimenting with different positions at different speeds until you
find a combination of height and rake angle that eliminates buffeting and gives
a smoother ride. You may have more than one favorite position, for example
shield tilted forward on cooler days, and shield tilted back for hot days to let
more air to your body.

PIVOT SCREWS
The MadStad brackets each have a pivot screw, located near the center of the
bottom bracket. A nylon lock nut keeps the screw snugly in place, yet allows
the brackets to slide back and forth. It is adjusted at the factory to have a
minimum of play yet still allow the brackets to move.
If for some reason you wish to adjust the tightness of this pivot screw or move
it to an alternate pivot position, use a 4mm Allen wrench along with a 10mm
socket or crescent wrench to make the adjustment. If you tighten the lock nut
completely you will not be able to slide the brackets.
Notes on Windshield Angle
Most windshields work best when set at a 55-60 degree angle. We have
provided an angle guide on the back page of this manual so that you can
check and see if your shield is set somewhere in this range.
To check your shield angle, your bike should be in an upright position either
on a center stand or held up by a helper. Set the spine (folded edge) of the
manual against the front of the shield. If the large arrow marked 60° is
pointing straight up, then your shield is at a 60 degree angle. (See diagram on
Page 5.) A little farther back and your angle would somewhere between 55
and 60 degrees. Anywhere in this range is fine for your initial test ride. On
some bikes a more vertical angle works better, so don’t be afraid to
experiment later if tilting the shield back doesn’t seem to be ideal.

Disclaimer
Neither MadStad Engineering nor its owners shall be liable for any
damages, consequential or inconsequential, resulting from the use of
our products. Installation of any of our products constitutes acceptance
of these terms.
It is the responsibility of the user to make sure all fasteners are
tightened securely, the windshield is mounted properly and the
adjustment knobs are tightened snugly before putting the motorcycle in
motion. MadStad systems ARE NOT intended to be adjusted while the
vehicle is in motion; you must pull over out of the way of traffic and
come to a complete stop before making any changes. The user must
never place the windshield in such a position as to interfere with the
safe and complete movement of the handlebars and controls.
Returns and Warranty
MadStad adjustable brackets carry a lifetime warranty against
manufacturing defects. This does not include cosmetic issues nor any
parts that inherently wear out or degrade over time such as rubber and
plastic parts. Windshields, deflectors, and other similar plastic parts are
warrantied for 1 year against manufacturing defects, not against
cosmetic issues or issues related to normal wear and tear. Please visit
our website for further details.

MadStad Engineering, Inc.
1451 E. Jefferson St.
Brooksville, FL 34601 U.S.A.
Phone: [phone]
Fax: [phone]
Web Site: http://www.madstad.com
Email: [email protected]
Thank you for your support, and ride safely!
April 13, 2018