Mahlkonig Guatemala User manual

GUATEMALA SB
GUATEMALA
www.mahlkoenig.de
GUATEMALA | GUATEMALA SB
INSTRUCTION MANUAL

Overview
A
1
2
3
9
8
7
6
5
4
11
10
GUATEMALA
*sample view
GUATEMALA SB
*not available in the USA
COFFEE GRINDER
2

B
C
8
12
13
14
GUATEMALA
*sample view
3
GUATEMALA | GUATEMALA SB | EN

E
D
15
5
17
16
17
3
GUATEMALA
*sample view
COFFEE GRINDER
4

F
10
18
19
G
20
21
GUATEMALA SB
*not available in the USA
GUATEMALA
*sample view
5
GUATEMALA | GUATEMALA SB | EN

23
I
22
GUATEMALA
*sample view
H
14 GUATEMALA
*sample view
COFFEE GRINDER
6

Scope of delivery
No. Name
1Bean hopper (with lid)
2Start buon
3Bag clamp lever
4Collecng tray
5Table
6Spout
7Adjusting cap
8Grinding degree scale
9Stop button
10 Vibrang basket
11 Spout chute
12 Release buon (thermal overcurrent circuit-breaker)
13 On/Offswitch
14 Power cable
15 Bag clamp
16 Table mount
17 Table adjusng screw
18 Vibrang basket adjusng screw
19 Vibrang basket holder
20 Adjusng spindle
21 Adjusng cap screw
22 Finger protecon
23 Bean hopper lid
7
GUATEMALA | GUATEMALA SB | EN

Guatemala
Contents
Overview ............................. 2
Scope of delivery ................. 7
General informaon ............ 9
Reading and storing the
instrucon manual........................ 9
Explanaon of symbols used ........ 9
Safety................................. 11
Intended use ............................... 11
Safety informaon ...................... 11
Before using....................... 14
Checking the grinder and
scope of delivery......................... 14
Seng up and connecng the
grinder......................................... 14
Operaon .......................... 16
Adding the coffee beans............. 17
Seng the grinding degree ........ 17
Preparing or inserng the
grounds container/coffee bag .... 17
Switching the grinder on/off....... 18
Starng the grinding process...... 18
Changing the coffee variety........ 18
Cleaning............................. 19
Cleaning the surface underneath
the grinder .................................. 20
Cleaning the casing..................... 20
Cleaning the adjusng cap.......... 21
Cleaning the bean hopper .......... 21
Cleaning the grinding mechanism
with GRINDZTM............................. 22
Troubleshoong ................ 23
Technical data.................... 26
Disposal ............................. 27
Disposing of the packaging......... 27
Disposing of the grinder ............. 27
Maintenance and service ........... 27
COFFEE GRINDER
8

General informaon
Reading and storing the instrucon manual
Before you start using the Guatemala | Guatemala SB coffee
grinder, read through this instrucon manual and the safety
informaon carefully. Only then will you be able to use the
Guatemala | Guatemala SB coffee grinder safely and without risk.
The instrucon manual is based on the standards and regulaons in force in
the European Union. Please also observe the guidelines and laws that apply
in your country.
For greater clarity, the Guatemala | Guatemala SB coffee grinder will be
referred to simply as the “grinder” below.
Retain this instrucon manual for future reference.
Pass this instrucon manual on to subsequent owners and
users of the grinder.
Explanaon of symbols used
The following symbols and signal words are used in this instrucon manual,
on the grinder, or on the packaging.
WARNING!
This signal word/symbol indicates a moderate risk, which, if
not avoided, can lead to death or serious injury.
CAUTION!
This signal word/symbol indicates a low risk, which, if not
avoided, can lead to minor or moderate injury.
NOTE!
This signal word warns of possible material damage.
9
GUATEMALA | GUATEMALA SB | EN

This symbol provides you with useful informaon about opera-
on or handling.
Declaraon of Conformity:
Products marked with this symbol fulfill all applicable Community
rules of the European Economic Area.
ETL Listed seal of approval:
Products marked with this symbol meet the requirements for
electrical product safety in the United States of America.
Products marked with this symbol meet the required criteria of
the NSF (Naonal Sanitaon Foundaon) regarding cleanliness
and hygiene in the food industry.
Products marked with this symbol are permied only for use
indoors.
This symbol indicates a risk of electric shock.
This symbol indicates that the grinder conforms to protecon
class I.
COFFEE GRINDER
10

Safety
Intended use
The grinder is suitable exclusively for grinding whole roasted coffee beans.
Do not use the grinder to grind other products or objects.
The grinder is intended for commercial use but is not suitable for connuous
high-volume producon. The grinder may only be maintained by trained
personnel. However, it may be operated by other persons in a place where
use is supervised.
Any other use is considered improper and can result in material damage or
even personal injury. Do not make any modificaons to the grinder. Neither
the manufacturer nor the retailer can accept liability for any injury or damage
resulng from failure to comply with the safety informaon.
Safety informaon
WARNING!
Risk of electric shock!
Improper use, incorrect electrical installaon, or a voltage that is too
high can all lead to electric shock.
– Connect the grinder only if the supply voltage of the socket
complies with the informaon indicated on the type plate.
– Connect the grinder only to an easily accessible socket to allow
you to disconnect it quickly from the power supply in the event
of a malfuncon.
– Do not use the grinder if you noce any visible damage or if the
power cable or plug is faulty.
– If the grinder power cable is damaged, it must be replaced by
the manufacturer or by qualified personnel in order to avoid
hazards.
– Do not operate the grinder without a ground connecon.
– Connect the grinder only to a power supply with a 16 A-slow
fuse. If the power connecon at the installaon locaon of the
grinder is not protected in this way, have a 16 A-slow fuse fied
by a qualified electrician.
11
GUATEMALA | GUATEMALA SB | EN

– Install the grinder only in locaons where its use can be super-
vised by trained personnel.
– Do not operate the grinder at altudes above 2,000 meters.
– Do not immerse the grinder, the power cable or the power plug
in water or any other liquids.
– Do not clean the grinder with a water jet or high-pressure clean-
er.
– Do not clean the grinder with compressed air
(e.g. with a compressed-air blow gun).
– Never touch the power plug with wet hands.
– Never unplug the power plug from the wall socket by pulling on
the power cable; always grip the power plug.
– Never carry the grinder by its power cable.
– Keep the grinder and power cable/power plug away from open
flames and hot surfaces.
– Do not posion the power cable in such a way that it could cre-
ate a tripping hazard.
– Do not bend the power cable and do not place it over sharp
edges.
– Use the grinder in indoor areas only. Never operate the grinder
in damp areas or in the rain.
– Keep children away from the grinder.
– Make sure that children do not insert any objects into the grind-
er.
– If you are not currently using the grinder, if you are cleaning it,
or if there is a malfuncon, switch the grinder offand remove
the power plug from the socket.
– Do not open the grinder casing, leave repairs to the experts.
If repairs are required, contact a specialist workshop. If unau-
thorized repairs are carried out, the connecon is not made
correctly, or the grinder is operated incorrectly, all liability and
warranty claims are voided. Only parts that comply with the
original appliance specificaons may be used for repairs. This
grinder contains electrical and mechanical parts that are essen-
al for protecon against potenal hazards.
COFFEE GRINDER
12

WARNING!
Danger for children and persons with reduced physical, sensory, or
mental capacies (e.g. parally disabled persons, elderly persons
with limited physical and mental capacies) or a lack of experience
and knowledge (e.g. older children).
– The grinder is not intended for use by children or persons with
reduced physical, sensory, or mental capabilies or with a lack
of experience and knowledge. Children may not play with the
grinder.
– Do not leave the grinder unsupervised when it is in operaon.
– Do not let children play with the packaging film. Children can
become entangled in it and suffocate while playing.
– Do not let children play with small parts. They can be life-threat-
ening if swallowed.
CAUTION!
Risk of pping and injury!
Incorrect handling of the grinder can result in injury.
– Lay out the power cable in such a way that nobody can become
entangled in it and cause the grinder to fall.
– Place the grinder on a level and stable surface to prevent it from
falling off.
13
GUATEMALA | GUATEMALA SB | EN

Before using
Checking the grinder and scope of delivery
NOTE!
Risk of damage!
Opening the packaging incauously with a sharp knife or other pointed
objects can damage the grinder.
– Proceed very carefully when opening.
1. Remove the grinder from its packaging.
2. Check that the delivery is complete (see Fig. A, B, D, E, and F).
3. Check for damage to the grinder or any of the individual parts.
If there is any damage, do not use the grinder. Contact your supplier (see
“Maintenance and service” secon).
Please note that the grinder has undergone a comprehensive
funconal test prior to delivery and may contain ground coffee
residue.
Seng up and connecng the grinder
1. Place the grinder on a level and stable surface that does not vibrate.
2. Make sure that the grinder is switched off(On/Offswitch (13) to 0) and
connect the grinder to the power supply by inserng the power plug (14)
into a properly installed safety socket.
3. Place the collecng tray (4) into the corresponding casing recess below
the table/vibrang basket.
• Do not operate the grinder without a collecng tray; the
coffee grounds could get into the inside of the grinder and
damage the grinder.
• Please note that the dispersion of the grounds depends on
the distance between the spout and the hopper: The less the
spacing, the less the dispersion of the coffee grounds.
COFFEE GRINDER
14

Guatemala
Adjust the table (5) to the desired height using the adjusng screw (17) (see
Fig. E).
1. Loosen the adjusng screw on the table using a slot screwdriver.
2. Insert the adjusng screw into the upper or lower hole on the table
mount (16).
3. Fasten the adjusng screw on the table using a slot screwdriver.
15
GUATEMALA | GUATEMALA SB | EN

Operaon
NOTE!
Risk of overheang!
Exceeding the maximum permissible operang cycle can cause the
grinder to overheat.
– Do not exceed the maximum operang cycle
(see “Technical data” secon).
– Observe the recommended break when the maximum permissi-
ble operang cycle is reached (see “Technical data”secon).
• The grinder has a thermal overcurrent circuit-breaker which
interrupts the electric circuit of the grinder in the event of an
electrical overload.
To use the grinder again, first set the On/Offswitch (13) to
switch posion 0(off).
Then push the release buon (12) in.
You can now switch the grinder on by seng the On/Off
switch to switch posion I and resume using the grinder (see
“Troubleshoong” secon).
• The grinder also has a motor protector, which switches off
the grinder when the motor becomes too hot.
As soon as the motor has cooled down, the grinder can be
put into operaon again (see “Troubleshoong” secon).
NOTE!
Risk of damage!
The operator cannot adjust the thermal overcurrent circuit-breaker. If
the circuit-breaker has been triggered several mes, a service partner
must be contacted for advice, as the motor winding may be damaged.
COFFEE GRINDER
16

Adding the coffee beans
1. Open the lid of the bean hopper (1).
2. Pour whole roasted coffee beans into the bean hopper from above.
The maximum filling quanty should be approx. 1 cm below the edge of
the bean hopper.
3. Close the lid of the bean hopper.
Seng the grinding degree
The grind adjustment’s grinding degree scale displays the
desired grinding degree.
The finest seng is “1”.
1. Make sure that you have inserted the power plug (14) into a properly
installed safety socket.
2. Turn the adjusng cap (7) towards “1” for fine coffee grinding and in the
opposite direcon for coarse coffee grinding (see Fig. B).
Preparing or inserng the grounds container/coffee bag
Depending on the model of your grinder, prepare the right container for
collecng the coffee grounds:
Grounds container/coffee bag for table/vibrang basket
1. Place a suitable grounds container or a coffee bag on the table (5) or the
vibrang basket (10).
2. If required, adjust the height of the table to suit the grounds container/
coffee bag using the adjusng screws (17) (see “Seng up and connect-
ing the grinder” subsecon).
3. Connue with the subsecon “Starng the grinding process”.
Grounds container/coffee bag in bag clamp
1. Insert a suitable grounds container/coffee bag into the bag clamp (15) by
holding down the bag clamp lever (3).
The bag clamp will liaway from the spout (6) at the sides (see Fig. D).
2. Put a coffee bag over the spout or posion a suitable grounds container
underneath it.
17
GUATEMALA | GUATEMALA SB | EN

3. Release the lever.
The bag clamp will close around the spout and hold the coffee bag or
grounds container.
4. Connue with the subsecon “Starng the grinding process”.
Switching the grinder on/off
1. Make sure that you have inserted the power plug (14) into a properly
installed safety socket.
2. Switch on the grinder by moving the On/Offswitch (13) to posion I.
3. Switch offthe grinder by moving the On/Offswitch to posion 0.
Starng the grinding process
1. Start the grinding process by pressing the start buon (2).
2. The grinding is completed as soon as you press the stop buon (9) or the
grinder is idling and no grinding noises are audible.
3. With one hand, secure the coffee bag/grounds container and press the
lever of the bag clamp (3) several mes in quick succession by tapping
the lever against the spout (6) a few mes.
Remove any grind residue scking to the grinder.
When the grinder model comes with a vibrang basket, there is
no need to manually tap the container.
4. Hold down the lever and remove the coffee bag/grounds container
containing the ground material from the spout or remove the coffee bag/
grounds container from the table (5)/vibrang basket (10).
Changing the coffee variety
1. Grind the coffee beans that remain in the grinding mechanism unl the
grinder runs empty.
2. Pour the new coffee beans into the bean hopper (1).
3. Grind 2 grams of the new coffee variety to remove any residues from the
old coffee beans and to warm up the machine.
COFFEE GRINDER
18

Cleaning
CAUTION!
Risk of injury!
The grinder can fall over and cause injury when it is being moved.
– Always place the grinder on a stable surface that will not lt.
– Ask another person for help if the grinder is too heavy.
NOTE!
Risk of short-circuit!
Water penetrang the grinder can cause a short-circuit.
– Never immerse the grinder in water or any other liquids.
– Never clean the grinder with a water jet.
– Ensure that no water or other liquids enter the casing in any
other way.
NOTE!
Risk of damage!
Improper handling can damage the grinder.
– Do not use any harsh cleaning agents or sharp or metallic clean-
ing tools such as knives, metal scouring pads, or similar. These
can scratch the surface.
– Do not clean the grinder with compressed air
(e.g. with a compressed-air blow gun).
– Do not put the drip tray or the lid of the bean hopper into the
dishwasher. These parts are not dishwasher-proof and the color
may fade.
– Do not lithe grinder by the bean hopper. Always lithe grind-
er by its casing using both hands.
19
GUATEMALA | GUATEMALA SB | EN

Cleaning the surface underneath the grinder
1. Switch offthe grinder (On/Offswitch (13) to posion 0) and remove the
power plug from the socket.
2. Lithe grinder by its casing with both hands and place it on another
surface that is clean.
3. Use a damp cloth to clean the surface on which the grinder is used and
then dry the surface.
The surface must be dry and free from oil and grease.
4. Use a damp cloth to clean the boom of the grinder by carefully pping
it to the side and then dry the boom.
The boom must be dry and free from oil and grease.
5. Place the grinder back onto the cleaned surface.
Cleaning the casing
1. Switch offthe grinder (On/Offswitch (13) to posion 0) and remove the
power plug from the socket.
2. Clean the following parts of the grinder with a brush:
• Spout (6),
• Spout chute (11),
• Bag clamp (15),
• Bag clamp lever (3),
• Table (5),
• Vibrang basket (10),
• Vibrang basket holder (19), table mount (16), adjusng screw (17)
for the table, adjusng screws (18) for the vibrang basket (leand
right).
3. Remove the collecng tray (4) by liing it out of the casing recess.
Wipe the casing and the collecng tray with a damp cloth as necessary,
but at least once a week.
4. Clean the mechanism of the bag clamp (3, 15) with a hand-held vacuum
cleaner.
5. Clean the power cable outlet (14, Fig. H) at the rear of the casing using a
brush and a hand-held vacuum cleaner.
COFFEE GRINDER
20