Mahlkonig E80 GbW Configuration guide

MAHLKONIG E80GBW-CLEANING PROCESS *LEAD BARISTA & BARISTA*
*Standardised settings as below*
*Dose setting*
*Cleaning required*
•Daily clean by juicer required as per E Campus
•Daily clean by Lead Barista or Barista required as per E Campus
•18g as per recipe
Dose setting

STEP 1-
Turn hopper slide gate to
left so that coffee beans
cannot drop
STEP 2-
Grind out all coffee from
burr chamber and throw
away until empty
STEP 3-
Turn hopper to left and
lift to remove
STEP 4-
Pour remaining beans into
an overnight bag and seal
MAHLKHONIG E80GBW GRINDER DAILY SHUTDOWN-CLEANING PROCEDURE-PAGE 1
*Procedure for Lead Barista and Barista only*
•Never place any grinder parts in the
dishwasher
•Never clean with anything abrasive
•Do not wet the grinder
•Always handle the grinder with
care so not to damage parts
STEP 7-
Turn inner collar to left to
unlock. Circle should align
with unlock image
STEP 5-
Purge steam into hopper to
disinfect- wipe dry with a
clean non-abrasive towel
STEP 6-
Loosen two locking screws
by turning to left -DO NOT
REMOVE SCREWS
STEP 8-
Remove cover
STEP 9-
Brush clean excess coffee
Grind from top

MAHLKHONIG E80GBW GRINDER DAILY SHUTDOWN-CLEANING PROCEDURE-PAGE 2
*Procedure for Lead Barista and Barista only*
STEP 10
Turn cover over and brush
off coffee near black ring
STEP 11-
Take clump crusher and
push up and down to
remove excess coffee
STEP 12-
Remove clump crusher
and wipe clean with dry
cloth
STEP 13-
Clump crusher should look
like this and place to side-
DO NOT LOSE
•Never place any grinder parts in the
dishwasher
•Never clean with anything abrasive
•Do not wet the grinder
•Always handle the grinder with
care so not to damage parts
STEP 14-
Loosen 3 x locking screws
on burr cover by turning
left-DO NOT REMOVE
SCREWS
STEP 15-
Turn burr cover to the right
into unlock position
STEP 17-
Clean burrs with paint brush
STEP 18-
Brush away any loose grind
moving burrs in a clockwise
direction until clean
STEP 16-
Remove burr cover

MAHLKHONIG E80GBW GRINDER DAILY SHUTDOWN-CLEANING PROCEDURE-PAGE 3
*Procedure for Lead Barista and Barista only*
STEP 19
Burrs should look like this
STEP 20-
Place top burr cover back
on
STEP 21-
Turn burr cover to left
into locking position
STEP 22-
Tighten 3 x locking screws-
Turn right
•Never place any grinder parts in the
dishwasher
•Never clean with anything abrasive
•Do not wet the grinder
•Always handle the grinder with
care so not to damage parts
STEP 23-
Place clean clump crusher
back in place
STEP 24-
Place cover back on into
position
STEP 26-
Tighten 2 x locking screws
– turn right
STEP 27-
Add clean hopper back to
grinder
STEP 25-
Turn collar to right and lock
into place

MAHLKHONIG E80GBW GRINDER DAILY SHUTDOWN-CLEANING PROCEDURE-PAGE 4
*Procedure for Lead Barista and Barista only*
•Never place any grinder parts in the
dishwasher
•Never clean with anything abrasive
•Do not wet the grinder
•Always handle the grinder with
care so not to damage parts
STEP 28-
Gently pull down on grind
chute
STEP 30-
Gently push chute back
into place until it locks in
STEP 29-
Clean any coffee residue
from inside of chute with a
dry cloth