Majestic LOGS-KMOD User manual

1Heat & Glo • LOGS-6KMOD, LOGS-8KMOD Log Instructions • 2584-935 Rev. B • 12/22
Log Set Assembly: LOGS-KMOD
Models: 6KMOD, 8KMOD, MER36MN, MER42MN
LOG PLACEMENT INSTRUCTIONS
Figure 2 Locations for Log Pins
Figure 2
CAUTION: Logs are fragile, handle with care.
NOTICE: To simplify the installation process, positively
identify each individual log before beginning installation.
See Figure 1.
Leave this manual with party responsible for use
and operation.
Log #1: Place Log #1 using the #4 and #6 log pins as guides as shown in Figure 4. The left end of the log will align with
the burner screw as shown in the top view illustrated in Figure 5.
4422665511337788
Figure 3 Log Pins Installed (6KMOD / MER36MN Base Pan Shown)
Installation
1. Fill round holes with included log pins as indicated in
Figure 2. Discard remaining log pins. Figure 3 shows
the log pins in the round holes.
Figure 4 Place Log #1 Figure 5 Top View of Log #1 in Position
11
11
BURNER SCREWBURNER SCREW
Figure 1 Log Identication
LOG PINSLOG PINS
44
2266
55
11
33
77
88
99
1010 1212
1111
6KMOD / MER36MN (12 PINS)
8KMOD / MER42MN (13 PINS)

Heat & Glo • LOGS-6KMOD, LOGS-8KMOD Log Instructions • 2584-935 Rev. B • 12/222
Log #2: Place the knot on the right end of Log #2 the left end of Log #1 as shown in Figure 7. Log Pin 1 touches the left
end of Log 2. See Figure 6.
Figure 6 Place Log #2 Figure 7 Knot on Log #2
Figure 8 Place Log #3 Figure 9 Place Log #4
KNOTKNOT
44
22
22
22
22
22
66
55
55
1111
11
11
33
33
Figure 10 Place Log #5
Figure 11 Place Log #6
LOG PIN 1LOG PIN 1
Log #3: Place the right end of Log #3 against Log Pin #8 as shown in Figure 8. Rotate the left end of Log #3 clockwise
until it touches Log Pin #3.
Log #4: Place the right end of Log #4 with Log Pins #10 and #11 as shown in Figure 9. Rest the left end of Log #4 on the
notch on Log#3 shown in Figure 8.
LOG PIN #3LOG PIN #3
NOTCH FOR LOG #4NOTCH FOR LOG #4
LOG PIN #10LOG PIN #10
Log #5: Place the left end of Log #5 with the pin as shown in Figure 10. Rotate the right end of Log #5 counter clockwise
until it contacts Log Pin #9.
Log #6: Place the bottom end of Log #6 using Log Pin #5 and Log Pin #7 as a guide. Set the top end of Log #6 on Log #1
as shown in Figure 11.
LOG PIN 7LOG PIN 7
LOG PIN #12LOG PIN #12
LOG PIN 8LOG PIN 8
LOG PIN #11LOG PIN #11
LOG PIN #9LOG PIN #9
LOG PIN 5LOG PIN 5
LOG CONTACTSLOG CONTACTS
RETURN BENDRETURN BEND

3Heat & Glo • LOGS-6KMOD, LOGS-8KMOD Log Instructions • 2584-935 Rev. B • 12/22
77
88
66
4433
6666
5555
7777
8888
4444
2222
11
11
11
3333
22
Figure 12 Place Log # 7 Figure 13 Place Log #8
Figure 14 6KMOD / MER36MN Shown - Base Pan Shown Unpainted Figure 15 8KMOD / MER42MN Shown - Base Pan Shown Painted
Note Log #7 & # 8 Positions
Log #7: Place Log #7 as shown in Figure 12. The forked end rests on the base pan.
8KMOD / MER42MN models only: See Figure 15 for additional details.
Log #8: Place Log #8 as shown in Figure 13. The small end rests against Pin #2.
8KMOD / MER42MN models only: See Figure 15 for additional details.
LOG #8 ANDLOG #8 AND
LOG #4 TOUCHLOG #4 TOUCH
PIN #2PIN #2
PIN #7PIN #7