Majestic MERID36IN User manual

1
Majestic • GL36MER, GL42MER Installation Instructions • 2502-931 Rev. B • 3/18
REQUIRED TOOLS
Screw gun equipped with 1/4 in (6 mm). socket or
1/4 in. (6 mm). wrench or socket
Small, at screwdriver
KIT COMPONENTS
(2) Side Glass Refractory Panels
(1) Rear Glass Refractory Panel
(1) Top Glass Refractory Panel
(2) Side Refractory Bracket
(1) Rear Refractory Bracket
(1) Rear Exhaust Bafe
(3) Screws
Leave this manual with party responsible for use
and operation.
Installation Instructions
1. Remove decorative front and logs.
2. Remove existing refractory or false back and discard,
if installed.
3. Remove ber refractory brackets (if so equipped) and
insert screws in the holes that remain. See Figure 1.
CAUTION! Risk of Cuts or Abrasions. Wear protective
gloves and safety glasses during installation.
NOTICE: Handle glass refractory panels with care.
Refractory may chip or crack if dropped or impacted.
GLASS REFRACTORY KIT
GL36MER, GL42MER
Models: MERID36IN, MERID36IL, MERID42IN, MERID42IL,
MERIDPLA36IN, MERIDPLA36IL, MERIDPLA42IN, MERIDPLA42IL
Installation Instructions
CAUTION! Do not install damaged components.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
Figure 1. Remove Fiber Refractory Brackets. Install Screw.
INSTALL SCREW
WARNING! Risk of Asphyxiation! DO NOT leave
holes open! Screws from ber refractory bracket removal
MUST be reinstalled in same holes as removed to main-
tain rebox seal.
4. Locate the six tabs on the basepan and bend upward.
They are circled in Figure 2. There are two tabs on
each side and two in the back.
Figure 2. Basepan Tab Locations
BEND 6 BASEPAN TABS
5. Using a small, at screwdriver, bend the ends of the
refractory brackets to a 90 degree angle as shown
in Figure 3. Break side refractory brackets apart by
bending back and forth.

2Majestic • GL36MER, GL42MER Installation Instructions • 2502-931 Rev. B • 3/18
7. Bend rear refractory bracket as shown in Figure 6.
8. Remove the existing rear bafe by removing two
screws indicated in Figure 9.
9. Install rear glass refractory panel. The bottom of the
panel is placed behind the tabs that have been bent
upward. See Figure 7. Secure the back glass panel
with the back refractory bracket and self-tapping screw
as shown in Figure 8. Center the rear refractory brack-
et prior to attaching it. It may be necessary to bend the
lower leg of bracket slightly more until it contacts the
glass.
Figure 6.
Figure 7. Side View of Bent Tabs
Figure 3. Glass Refractory Brackets Bent
Figure 5. Glass Refractory Brackets Installed
6. MERIDPLA Only: Place glass brackets in position
and insert screws. See Figure 4 and Figure 5 for ap-
proximate placement. Do not tighten screws at this
time. They may need adjustment once glass panels
are installed.
POSITION PANEL BEHIND
BENT TAB
MERID Only: Remove one screw from the glass shield
and place the retention bracket as shown in Figure 4.
Reinstall the screw, but do not tighten completely at
this time. Repeat this step to install retention bracket
on the other side.
Figure 4. Retention Bracket Installed
GLASS SHIELD
RETENTION BRACKET
(LEFT AND RIGHT SIDES)
BEND 90°
BEND APPROXIMATELY 90°
LOWER LEG

3
Majestic • GL36MER, GL42MER Installation Instructions • 2502-931 Rev. B • 3/18
12. Reinstall logs using log placement instructions in ap-
pliance installation manual. Reinstall decorative front.
Please contact your Majestic dealer with any questions
or concerns.
For the location of your nearest Majestic dealer,
please visit www.majesticproducts.com.
Majestic, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.majesticproducts.com
Figure 11. Glass Refractory Installed
Figure 10. Rear Exhaust Bafe Tabs
TOP TAB
BOTTOM TAB - BEND BOTTOM TABS UP
BEND TABS OVER TOP GLASS
REFRACTORY PANEL
13. Place center glass panel on the rear exhaust bafe.
The glass panel will be held in place by the bottom
tabs bent up in Step 12. Bend tabs on the top over
the glass panel to secure it in place. See Figure 10
and Figure 11.
10. Slide one side panel behind bent tabs until side panel
is ush with rear glass panel. Slide glass refracto-
ry bracket, installed in Step 6, toward the glass and
tighten the screw. Do not overtighten. Repeat pro-
cess to install the other side panel. See Figure 8.
Figure 8. Side Panel Flush with Rear Panel
12. Bend the small tabs on the bottom of the rear exhaust
bafe upward. See Figure 10.
SIDE
PANEL REAR
PANEL
BACK REFRACTORY
BRACKET INSTALLED
11. Install and secure new rear exhaust bafe with two
screws as shown in Figure 9.
SCREWS
REAR EXHAUST BAFFLE INSTALLED
Figure 9. Rear Exhaust Bafe Installed