Makita DUB361 Manual

Model DUB361 is a cordless blower powered by two 18V Li-ion batteries in series.
This main features are:
• High/ Low push button for two different air volume settings
• Battery capacity warning lamp
• XPT (eXtreme Protection Technology)
This product is available in the next page variations.
Note: 1.3Ah Li-ion battery of BL1815 cannot be used for this model.
Dimensions: mm (")
Width (W)
Height (H)
Length (L1)
Length (L2)
141 (5-5/8)
420 (16-1/2)
905 (35-5/8)
194 (7-5/8)
W
H
L1
L2
CONCEPT AND MAIN APPLICATIONS
Specification
Model No. DUB361
Description Cordless Blower
Battery
Max air velocity*1: m/sec.
Energy capacity: Wh
Voltage: V
Capacity: Ah
Weight according to
EPTA-Procedure 01/2003*1: kg (lbs)
Cell Li-ion
Charging time (approx.): min.
36 (18x2)
2.6
93
57
17*2, 24*3
51*2, 73*3
No
No
2.6 (5.9)*4
3.1 (6.9)*5
Yes (2 settings: High/ Low)
4.4
No load speed: min.-1 = rpm
Air volume setting function
Vacuum function
Variable speed control by trigger
Continuous run time (approx.)
on a single full battery: min.
High
Low
High
Low
High
Low
High
Low
17,000
10,000
1.5, 2.0, 3.0, 4.0, 5.0
Max air volume: m3/min.
*1 With Long nozzle *2 With two batteries BL1830 *3 With two batteries BL1840
*4 With two batteries BL1815N or BL1820
*5 With two batteries BL1830, BL1840 or BL1850
Optional accessories
Battery BL1815N Fast charger DC18RC
Battery BL1820 Charger DC24SC
Battery BL1830 Charger DC18SD
Battery BL1840 Quad port charger DC18SF
Battery BL1850 Automotive charger DC18SE
Standard equipment
Battery*6
Battery cover*6
Charger*6
Long nozzle
Shoulder strap
*6 Battery, Battery cover and charger are not supplied with “Z” model.
Note: The standard equipment may vary by country or model variation.
PRODUCT
P 1/ 6
TECHNICAL INFORMATION
OFFICIAL USE
for ASC & Sales Shop
15x2, 24x2, 22x2, 36x2, 45x2 with DC18RC
27x2, 36x2, 54x2, 72x2, 90x2

P 2/ 6
Fig. 1
Repair
It is not required to lubricate the machine because of no gear mechanism to be lubricated.
[3] DISASSEMBLY/ASSEMBLY
[3] -1. Fan 95, Armature
[1] NECESSARY REPAIRING TOOLS
CAUTION: Repair the machine in accordance with “Instruction manual” or “Safety instructions”.
Code No.
---
Description Use for
Socket bit 8-55 (width across flats: 8mm) Disassembling/ Assembling M5-8 Hex nut for Fan 95
[2] LUBRICATION
DISASSEMBLING
(1) Disassemble Motor section from Housing (L) as drawn in Fig. 1.
Holder cap cover
2. Remove Holder cap covers, Holder caps and Carbon Brushes
from the both side of the machine.
3. Remove Housing (R) by unscrewing
fourteen 4x18 tapping screws.
4. Separate Armature section together
with Yoke unit from Endbell complete.
1. Remove Long nozzle
Holder cap
Carbon brush
Long nozzle
Endbell
complete
Yoke unit
Armature

P 3/ 6
Fig. 2
Repair
[3] DISASSEMBLY/ASSEMBLY
[3] -1. Fan 95, Armature (cont.)
DISASSEMBLING
(2) Disassemble Fan 95 as drawn in Fig. 2.
8-55 Socket bit
M5-8 Hex nut
1. Hold Fan 95 by hand and turn M5-8 Hex nut clockwise using cordless impact
driver with Socket bit 8-55.
Note: M5-8 Hex nut is left hand thread.
Remove Flat washer 5, Fan 95 and Flat washer 8 from the end of Armature.
2. Pull off Armature
from Yoke unit.
Flat washer 8
Fan 95 Fan 95
Yoke unit
Armature
Flat washer 5

P 4/ 6
Fig. 3
Repair
ASSEMBLING
1. Assemble Motor section while fitting two notches of
Yoke unit to two projections of Housing (L).
2. Be sure that Hanger is mounted to the following
place before mounting Housing (R).
two notches of
Yoke unit
Hanger
two projections
of Housing (L)
Assemble by reversing the disassembly procedure. (Figs. 2 and 1)
Note:
(1) Do not forget to set Flat washer 5 and Flat washer 8 in place. (Fig. 2)
(2) Fit two notches of Yoke unit to two projections on Housing (L). (Fig. 3)
(3) Before assembling Housing (R), mount Hanger on Housing (L). (Fig. 3)
[3] -2. Switch unit
DISASSEMBLING
Fig. 4
Connector
(1) Disassemble Housing (R) from Housing (L) as drawn in Fig. 1.
It is not necessary to remove Motor section.
(2) Remove Switch unit by disconnecting Connectors as drawn in Fig. 4.
Connector
Switch unit
Switch unit
[3] DISASSEMBLY/ASSEMBLY
[3] -1. Fan 95, Armature (cont.)

P 5/ 6
Fig. D-1
Circuit diagram
White Orange
Blue
Yellow
Color index of lead wires' sheath
Black
Red
Endbell
complete
Controller
Line filter
Connector Housing (R) side
Housing (L) side

P 6/ 6
Fig. D-2
Wiring diagram
Wiring to Terminal Setting of Terminal to Housing (L)
Setting of Battery capacity warning lamps A, B
Set Flag connectors to Terminals A and B
as shown above.
Set Terminals A and B to Housing (L)
as shown above.
Flag connector Flag connector
Terminal A
Terminal B Terminal A
Terminal B
Battery capacity warning lamp A
Battery capacity warning lamp B
Put Battery capacity warning lamps A and B
while facing their wires connected portion to
Terminals A and B side.
Terminal A Terminal B
Rib A Rib B
Line filter
Closed end splice
Rib F
Battery capacity
warning lamp A
Terminal A
Terminal B
Battery capacity
warning lamp B
Rib E
Rib C
Rib D
Be careful not to put
any Lead wires
on these Ribs.
Put Closed end splices and
Line filter here.
Put the following Lead wires with
these Lead wire holders.
* Endbell’s Lead wires (black, red)
* Controller’s Lad wires (black, red)
Do not put any Lead wires
between Ribs A and B.
Put Lead wires of Switch
unit between Ribs C and D.
Wiring diagram in Housing (L)
Put the following Lead wires between Ribs E and F.
* Lead wires (red, black, yellow) of Terminal A
* Lead wire (red, black) of Battery capacity warning lamp A