Makita UB003C User manual

INSTRUCTION MANUAL
Battery Powered Blower
UB003C
ENGLISH: Original instructions
Read before use.
Read before use.

2ENGLISH
SPECIFICATIONS
Model: UB003C
Capacities Air volume 2.9 - 17.6 m3/min
Air speed (average) 11.7 - 71.9 m/s
Air speed (max.) 86.0 m/s
Overall length (with end nozzle) 913 mm / 963 mm / 1,013 mm
Rated voltage D.C. 36 V - 40 V max
Net weight 2.8 - 3.1 kg
Protection degree IPX4
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsmaydi󰀨erfromcountrytocountry.
• Weight according to EPTA-Procedure 01/2014
Applicable portable power pack
PDC1200 / PDC1500
WARNING: Only use the portable power
packs listed above.Useofanyotherportablepower
packsmaycauseinjuryand/orre.
Symbols
Thefollowingsshowthesymbolswhichmaybeused
fortheequipment.Besurethatyouunderstandtheir
meaning before use.
Take particular care and attention.
Read instruction manual.
Keephandsawayfromrotatingparts.
Longhairmaycauseentanglement
accident.
Keepbystandersaway.
Weareyeandearprotection.
Do not expose to moisture.
Ni-MH
Li-ion
OnlyforEUcountries
Due to the presence of hazardous com-
ponents in the equipment, waste electrical
and electronic equipment, accumulators
andbatteriesmayhaveanegativeimpact
on the environment and human health.
Do not dispose of electrical and electronic
appliances or batteries with household waste!
In accordance with the European Directive
on waste electrical and electronic equip-
ment and on accumulators and batteries
and waste accumulators and batteries,
as well as their adaptation to national law,
waste electrical equipment, batteries and
accumulatorsshouldbestoredseparately
and delivered to a separate collection point
for municipal waste, operating in accor-
dance with the regulations on environmen-
tal protection.
Thisisindicatedbythesymbolofthe
crossed-out wheeled bin placed on the
equipment.
Intended use
The machine is intended for blowing dust.
About this instruction manual
Theterm"battery","batterycartridge",or"batterypack"
in this instruction manual refers to "portable power
pack".
SAFETY WARNINGS
General power tool safety warnings
WARNING Read all safety warnings, instruc-
tions, illustrations and specications provided with
this power tool. Failure to follow all instructions listed
belowmayresultinelectricshock,reand/orserious
injury.
Save all warnings and instruc-
tions for future reference.
Theterm"powertool"inthewarningsreferstoyour
mains-operated(corded)powertoolorbattery-operated
(cordless) power tool.

3ENGLISH
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
whichmayignitethedustorfumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
youtolosecontrol.
Electrical safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiedplugsandmatchingoutletswill
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tricshockifyourbodyisearthedorgrounded.
3. Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
6. If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
7.
Power tools can produce electromagnetic elds
(EMF) that are not harmful to the user. However,
users of pacemakers and other similar medical
devices should contact the maker of their device and/
or doctor for advice before operating this power tool.
Personal safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inuence of drugs, alcohol or med-
ication. A moment of inattention while operating
powertoolsmayresultinseriouspersonalinjury.
2. Use personal protective equipment. Always
wear eye protection. Protective equipment such
asadustmask,non-skidsafetyshoes,hardhator
hearing protection used for appropriate conditions
willreducepersonalinjuries.
3. Prevent unintentional starting. Ensure the
switch is in the o󰀨-position before connecting
to power source and/or battery pack, picking
up or carrying the tool.Carryingpowertoolswith
yourngerontheswitchorenergisingpowertools
that have the switch on invites accidents.
4.
Remove any adjusting key or wrench before turning
the power tool on.Awrenchorakeyleftattachedtoa
rotatingpartofthepowertoolmayresultinpersonalinjury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts.Looseclothes,jewelleryor
long hair can be caught in moving parts.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
8. Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action
cancausesevereinjurywithinafractionofa
second.
9. Always wear protective goggles to protect
your eyes from injury when using power tools.
The goggles must comply with ANSI Z87.1 in
the USA, EN 166 in Europe, or AS/NZS 1336
in Australia/New Zealand. In Australia/New
Zealand, it is legally required to wear a face
shield to protect your face, too.
It is an employer's responsibility to enforce
the use of appropriate safety protective equip-
ments by the tool operators and by other per-
sons in the immediate working area.
Power tool use and care
1. Do not force the power tool. Use the correct
power tool for your application. The correct
powertoolwilldothejobbetterandsaferatthe
rate for which it was designed.
2. Do not use the power tool if the switch does
not turn it on and o󰀨.Anypowertoolthatcannot
be controlled with the switch is dangerous and
must be repaired.
3. Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any adjust-
ments, changing accessories, or storing power
tools.Suchpreventivesafetymeasuresreduce
theriskofstartingthepowertoolaccidentally.
4. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
5. Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may a󰀨ect the power tool’s operation. If dam-
aged, have the power tool repaired before use.
Manyaccidentsarecausedbypoorlymaintained
power tools.

4ENGLISH
6. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges
arelesslikelytobindandareeasiertocontrol.
7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power tool
foroperationsdi󰀨erentfromthoseintendedcould
result in a hazardous situation.
8. Keep handles and grasping surfaces dry,
clean and free from oil and grease.Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpected
situations.
9. When using the tool, do not wear cloth work
gloves which may be entangled. The entangle-
mentofclothworkglovesinthemovingpartsmay
resultinpersonalinjury.
Battery tool use and care
1. Recharge only with the charger specied by
the manufacturer. A charger that is suitable for
onetypeofbatterypackmaycreateariskofre
whenusedwithanotherbatterypack.
2. Use power tools only with specically desig-
nated battery packs.Useofanyotherbattery
packsmaycreateariskofinjuryandre.
3. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another.Shortingthebatterytermi-
nalstogethermaycauseburnsorare.
4. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If con-
tact accidentally occurs, ush with water. If
liquid contacts eyes, additionally seek medical
help.Liquidejectedfromthebatterymaycause
irritation or burns.
5. Do not use a battery pack or tool that is dam-
aged or modied.Damagedormodiedbatteries
mayexhibitunpredictablebehaviourresultingin
re,explosionorriskofinjury.
6. Do not expose a battery pack or tool to re or
excessive temperature.Exposuretoreortem-
peratureabove130°Cmaycauseexplosion.
7. Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specied in the instruc-
tions.Chargingimproperlyorattemperatures
outsidethespeciedrangemaydamagethe
batteryandincreasetheriskofre.
Service
1. Have your power tool serviced by a qualied
repair person using only identical replacement
parts.Thiswillensurethatthesafetyofthepower
tool is maintained.
2. Never service damaged battery packs. Service
ofbatterypacksshouldonlybeperformedbythe
manufacturer or authorized service providers.
3. Follow instruction for lubricating and chang-
ing accessories.
Battery Powered Blower Safety
Instructions
WARNING: Read all safety warnings and
all instructions. Failure to follow the warnings and
instructionsmayresultinelectricshock,reand/or
seriousinjury.
Save all warnings and instruc-
tions for future reference.
Training
1. Read the instructions carefully. Be familiar
with the controls and the correct use of the
blower.
2. Never allow children, persons with reduced
physical, sensory or mental capabilities or
lack of experience and knowledge or people
unfamiliar with these instructions to use the
blower. Local regulations may restrict the age
of the operator.
3. Never operate the blower while people, espe-
cially children, or pets are nearby.
4. Keep in mind that the operator or user is
responsible for accidents or hazards occurring
to other people or their property.
Preparation
1. Always wear substantial footwear and long
trousers while operating the blower.
2. Do not wear loose clothing or jewellery that
can be drawn into the air inlet. Keep long hair
away from the air inlets.
3. Always wear protective goggles to protect
your eyes from injury when using power tools.
The goggles must comply with ANSI Z87.1 in
the USA, EN 166 in Europe, or AS/NZS 1336
in Australia/New Zealand. In Australia/New
Zealand, it is legally required to wear a face
shield to protect your face, too.
It is an employer's responsibility to enforce
the use of appropriate safety protective equip-
ments by the tool operators and by other per-
sons in the immediate working area.
4. To prevent dust irritation the wearing of a face
mask is recommended.
5. While operating the machine, always wear
non-slip and protective footwear. Non-skid,
closed-toedsafetybootsandshoeswillreducethe
riskofinjury.

5ENGLISH
6. Use personal protective equipment. Always
wear eye protection. Protective equipment such
asadustmask,non-skidsafetyshoes,hardhator
hearing protection used for appropriate conditions
willreducepersonalinjuries.
7. Inspect the cord before operating the machine.
If the cord is damaged, ask Makita Authorized
Service Centers for repair.
Operation
1. Switch o󰀨 the blower and remove the battery
and make sure that all moving parts have
come to a complete stop
• whenever you leave the blower.
• before clearing blockages.
• before checking, cleaning or working on
the blower.
• if the blower starts to vibrate abnormally.
2. Operate the blower only in daylight or in good
articial light.
3. Do not overreach and keep proper balance and
footing at all times.
4. Always be sure of your footing on slopes.
5. Walk, never run.
6. Keep all cooling air inlets clear of debris.
7. Never blow debris in the direction of
bystanders.
8. Operate the blower in a recommended position
and on a rm surface.
9. Do not operate the blower at high places.
10. Never point the nozzle at anyone in the vicinity
when using the blower.
11. Never block suction inlet and/or blower outlet.
• Be careful not to block suction inlet or
blower outlet with dust or dirt when oper-
ating in dusty area.
• Do not use nozzles other than the nozzles
provided by Makita.
• Do not use the blower to inate balls,
rubber boat or the similar.
12. Do not operate the blower near open window,
etc.
13. Operating the blower only at reasonable hours
is recommended - not early in the morning or
late at night when people might be disturbed.
14. Using rakes and brooms to loosen debris
before blowing is recommended.
15. If the blower strikes any foreign objects or
should start making any unusual noise or
vibration, immediately switch o󰀨 the blower
to stop it. Remove the battery from the blower
and inspect the blower for damage before
restarting and operating the blower. If the
blower is damaged, ask Makita Authorized
Service Centers for repair.
16. Do not insert ngers or other objects into
suction inlet or blower outlet.
17. Prevent unintentional starting. Ensure the
switch is in the o󰀨-position before inserting
battery, picking up or carrying the blower.
Carrying the blower with your nger on the
switch or energizing the blower that has the
switch on invites accidents.
18. Never blow dangerous materials, such as
nails, fragments of glass, or blades.
19. Do not operate the blower near ammable
materials.
20. Avoid operating the blower for a long time in
low temperature environment.
21. Do not use the machine when there is a risk of
lightning.
22. When you use the machine on muddy ground,
wet slope, or slippery place, pay attention to
your footing.
23. Avoid working in poor environment where
increased user fatigue is expected.
24. Do not use the machine in bad weather where
visibility is limited.Failuretodosomaycause
fallorincorrectoperationduetolowvisibility.
25. Do not submerge the machine into a puddle.
26. When wet leaves or dirt adhere to the suc-
tion mouth (ventilation window) due to rain,
remove them.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure
the blower is in safe working condition.
2. If the parts are worn or damaged, replace them
with parts provided by Makita.
3. Store the blower in a dry place out of the reach
of children.
4. When you stop the blower for inspection, ser-
vicing, storage, or changing accessory, switch
o󰀨 the blower and make sure that all moving
parts come to a complete stop, and remove the
battery. Cool down the blower before making
any work on the blower. Maintain the blower
with care and keep it clean.
5. Always cool down the blower before storing.
6. Do not expose the blower to rain. Store the
blower indoors.
7. When you lift the blower, be sure to bend your
knees and be careful not to hurt your back.
8. Do not leave the machine unattended outdoors
in the rain.
9. Do not wash the machine with high pressure
water.
10. When storing the machine, avoid direct sun-
light and rain, and store it in a place where it
does not get hot or humid.
11. Perform inspection or maintenance in a place
where rain can be avoided.
12. After using the machine, remove the adhered
dirt and dry the machine completely before
storing. Depending on the season or the area,
there is a risk of malfunction due to freezing.
13. Do not pick up or carry the machine by holding
only the cord.
14. Do not modify or attempt to repair the machine
or the battery pack except as indicated in the
instructions for use and care.
Battery tool use and care
1. Recharge only with the charger specied by
the manufacturer. A charger that is suitable for
onetypeofbatterypackmaycreateariskofre
whenusedwithanotherbatterypack.

6ENGLISH
2. Use power tools only with specically desig-
nated battery packs.Useofanyotherbattery
packsmaycreateariskofinjuryandre.
3. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another.Shortingthebatterytermi-
nalstogethermaycauseburnsorare.
4.
Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acci-
dentally occurs, ush with water. If liquid contacts
eyes, additionally seek medical help.Liquidejected
fromthebatterymaycauseirritationorburns.
5. Do not use a battery pack or tool that is dam-
aged or modied.Damagedormodiedbatteries
mayexhibitunpredictablebehaviourresultingin
re,explosionorriskofinjury.
6. Do not expose a battery pack or tool to re or
excessive temperature.Exposuretoreortem-
peratureabove130°Cmaycauseexplosion.
7. Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specied in the instruc-
tions.Chargingimproperlyorattemperatures
outsidethespeciedrangemaydamagethe
batteryandincreasetheriskofre.
Electrical and battery safety
1. Do not dispose of the battery(ies) in a re.
Thecellmayexplode.Checkwithlocalcodesfor
possible special disposal instructions.
2. Do not open or mutilate the battery(ies).
Releasedelectrolyteiscorrosiveandmaycause
damagetotheeyesorskin.Itmaybetoxicif
swallowed.
3.
Do not charge battery in rain, or in wet locations.
4. Do not charge the battery outdoors.
5. Do not handle charger, including charger plug,
and charger terminals with wet hands.
6. Do not replace the battery in the rain.
7. Do not wet the terminal of battery with liquid
such as water, or submerge the battery. Do not
leave the battery in the rain, nor charge, use,
or store the battery in a damp or wet place. If
the terminal gets wet or liquid enters inside of bat-
tery,thebatterymaybeshortcircuitedandthereis
ariskofoverheat,re,orexplosion.
8. After removing the battery from the machine or
charger, be sure to attach the battery cover to
the battery and store it in a dry place.
9. Do not replace the battery with wet hands.
10. If the battery gets wet, drain the water inside
and then wipe it with a dry cloth. Dry the bat-
tery completely in a dry place before use.
Service
1. Have your power tool serviced by a qualied
repair person using only identical replacement
parts.Thiswillensurethatthesafetyofthepower
tool is maintained.
2. Never service damaged battery packs. Service
ofbatterypacksshouldonlybeperformedbythe
manufacturer or authorized service providers.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product.
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
2. Do not disassemble or tamper with the battery
cartridge.Itmayresultinare,excessiveheat,
or explosion.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4.
If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdown.
6. Do not store and use the tool and battery car-
tridge in locations where the temperature may
reach or exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the
battery cartridge.Suchconductmayresultina
re,excessiveheat,orexplosion.
9. Do not use a damaged battery.
10.
The contained lithium-ion batteries are subject to
the Dangerous Goods Legislation requirements.
Forcommercialtransportse.g.bythirdparties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Pleasealsoobservepossiblymoredetailed
national regulations.
Tapeormasko󰀨opencontactsandpackupthe
batteryinsuchamannerthatitcannotmove
around in the packaging.
11. When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.

7ENGLISH
12. Use the batteries only with the products
specied by Makita. Installing the batteries to
non-compliantproductsmayresultinare,exces-
siveheat,explosion,orleakofelectrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
14. During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool imme-
diately after use as it may get hot enough to
cause burns.
16. Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge.Itmaycauseheating,catchingre,
burstandmalfunctionofthetoolorbatterycar-
tridge,resultinginburnsorpersonalinjury.
17. Unless the tool supports the use near
high-voltage electrical power lines, do not use
the battery cartridge near high-voltage electri-
cal power lines.Itmayresultinamalfunctionor
breakdownofthetoolorbatterycartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
havebeenaltered,mayresultinthebatterybursting
causingres,personalinjuryanddamage.Itwill
alsovoidtheMakitawarrantyfortheMakitatooland
charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4. When not using the battery cartridge, remove
it from the tool or the charger.
5. Charge the battery cartridge if you do not use
it for a long period (more than six months).
ASSEMBLY
CAUTION: Always be sure that the machine is
switched o󰀨 and the portable power pack is dis-
connected from the machine before carrying out
any work on the machine.
Installing the end nozzle
Align the triangle mark on the end nozzle with the trian-
gle mark on the front pipe, then attach the end nozzle
to the front pipe, and then turn the end nozzle to lock it
into place.
Install the end nozzle so that the tip of the nozzle faces
downward.Dependingontheworkingenvironment,you
can install the end nozzle so that the tip of the nozzle is
facing up.
11
2 3
Fig.1
►1. Triangle mark 2. End nozzle 3. Front pipe
To remove the end nozzle, perform the installation
procedure in reverse.
NOTE:Thelengthofthenozzlecanbechangedby
movingthenozzleasshowninthegure.
1 2
Fig.2
►1. End nozzle 2. Front pipe

8ENGLISH
Installing the at nozzle
Optional accessory
NOTE: If the end nozzle is installed, remove it before
installingtheatnozzle.
1. Align the groove on the adapter pipe with the pro-
trusion on the front pipe, then attach the adapter pipe to
the front pipe, and then turn it to lock it into place.
2
1
Fig.3
►1. Adapter pipe 2. Front pipe
2. Alignthegrooveontheatnozzlewiththeprotru-
sionontheadapterpipe,thenattachtheatnozzleto
the adapter pipe, and then turn it to lock it into place.
12
Fig.4
►1. Flat nozzle 2. Adapter pipe
FUNCTIONAL
DESCRIPTION
CAUTION: Always be sure that the machine
is switched o󰀨 and the portable power pack is
disconnected from the machine before adjusting
or checking function on the machine.
Machine / battery protection system
Themachineisequippedwithamachine/battery
protectionsystem.Thissystemautomaticallycutso󰀨
powertothemotortoextendmachineandbatterylife.
Themachinewillautomaticallystopduringoperationif
themachineorbatteryisplacedunderoneofthefol-
lowing conditions:
Overload protection
Whenthemachineorbatteryisoperatedinamanner
thatcausesittodrawanabnormallyhighcurrent,the
machineautomaticallystopsandthespeedindicator
blinksingreen.Inthissituation,turnthemachineo󰀨
and stop the application that caused the machine to
become overloaded. Then turn the machine on to
restart.
Overheat protection
Whenthemachineorbatteryisoverheated,the
machinestopsautomatically.Whenthemachineis
overheated, the speed indicator lights up in red. When
thebatteryisoverheated,thespeedindicatorblinks
inred.Letthemachineandbatterycooldownbefore
turning the machine on again.
Overdischarge protection
Whenthebatterycapacityisnotenough,themachine
stopsautomaticallyandthespeedindicatorblinksin
red.Inthiscase,removethebatteryfromthemachine
andchargethebatteryorchangethebatterytofully
charged one.
Protections against other causes
Protectionsystemisalsodesignedforothercausesthat
could damage the machine and allows the machine to
stopautomatically.Takeallthefollowingstepstoclear
the causes, when the machine has been brought to a
temporaryhaltorstopinoperation.
1. Turnthemachineo󰀨,andthenturnitonagainto
restart.
2. Chargethebattery(ies)orreplaceit/themwith
rechargedbattery(ies).
3. Letthemachineandbattery(ies)cooldown.
Ifnoimprovementcanbefoundbyrestoringprotection
system,thencontactyourlocalMakitaServiceCenter.
NOTICE: If the machine stops due to a cause
not described above, refer to the section for
troubleshooting.

9ENGLISH
Main power switch
WARNING: Always turn o󰀨 the main power
switch when not in use.
To turn on the machine, press the main power switch.
Thespeedindicatorslightupingreen.Toturno󰀨,press
and hold the main power switch until the speed indica-
torsgoo󰀨.
The speed can be changed in three levels. To change
the speed mode, press the main power switch. When
youchangethespeedmode,thecorrespondingspeed
indicators light up.
1
2
Fig.5
►1. Speed indicator 2. Main power switch
NOTE:Thismachineemploystheautopower-o󰀨
function. To avoid unintentional start up, the main
powerswitchwillautomaticallyshutdownwhenthe
switch trigger is not pulled for a certain period after
the main power switch is turned on.
NOTE:Ifyoupressthemainpowerswitchwhenthe
controlleverisnotfullyreturnedtotheo󰀨position,
orwhileyouarepullingtheswitchtrigger,themain
powerlampblinksingreen.Inthiscase,fullyreturn
the control lever, or release the switch trigger, and
then press the main power switch.
Battery check button
Youcanchecktheremainingbatterycapacitybypress-
ingthebatterycheckbutton.
1
2
Fig.6
►1.Batteryindicator2.Batterycheckbutton
Battery indicator status Remaining
battery
capacity
On O󰀨 Blinking
50% to 100%
20% to 50%
0% to 20%
NOTE:Theindicatorlampforremainingbattery
capacityisjustforareference.Theactualbattery
capacitymaydi󰀨erdependingontheusagecondi-
tions or ambient temperature.
NOTE: While the machine is in operation, the indica-
torlampdoesnotlightupevenifyoupressthecheck
button.
NOTE:Thelampautomaticallygoeso󰀨afterafew
seconds.
Switch action
WARNING: Before connecting the portable
power pack to the machine, always check to see
that the switch trigger actuates properly and
returns to the "OFF" position when released.
Tostartthemachine,simplypulltheswitchtrigger.The
speedincreasesbyincreasingpressureontheswitch
trigger. Release the switch trigger to stop.
1
Fig.7
►1. Switch trigger

10 ENGLISH
Cruise control function
The cruise control function allows the operator to main-
tain a constant speed without pulling the trigger. To
increase the speed, turn the control lever forward. To
decrease the speed, turn the control lever backward.
1
Fig.8
►1. Control lever
Accidental re-start preventive
function
Whenyouturnonthemachinewhilepullingtheswitch
trigger, the machine does not start and the speed indi-
catorblinksingreen.Tostartthemachine,rstrelease
theswitchtriggerandreturnthecontrolleverfully,and
then turn on the machine.
OPERATION
Connecting the portable power pack
CAUTION: When you use the machine in com-
bination of the backpack-type power supply such
as portable power pack, use the hanging band
included in the machine package or the hanging
band recommended by Makita.
Ifyouputontheshoulderharnessnotrecommended
byMakitaandtheshoulderharnessoftheback-
pack-typepowersupplyatthesametime,removing
themachineorbackpack-typepowersupplyisdif-
cultincaseofanemergency,anditmaycausean
accidentorinjury.Fortherecommendedhanging
band, ask Makita Authorized Service Centers.
CAUTION: Before operation, make sure that
the buckles on the waist belt is locked and the
machine is securely attached to the hook of the
hanging band.
CAUTION: To prevent unintentional start up,
make sure that the machine and portable power
pack are turned o󰀨 before starting this procedure.
CAUTION: Before performing this procedure,
nish the adjustments for the waist belt and
shoulder harness. Refer to the instruction manual of
the portable power pack for details.
CAUTION: When removing the battery, press
the lock button while holding the handle rmly.
2
1
Fig.9
►1. Handle 2. Lock button
CAUTION: Be careful not to pinch your
ngers or thumbs between the battery and the
shoulder harness assembly when attaching the
battery.
CAUTION: Make sure that the battery is
securely xed to the shoulder harness assembly.
Otherwise,thebatterymayfallwhenyouputonthe
unitorusetheunit,andcauseaninjury.Ifyoucan
seetheredindicatorasshowninthegure,thebat-
teryisnotlockedcompletely.
1
Fig.10
►1. Red indicator

11 ENGLISH
1. Removethebatteryfromtheshoulderharness
assembly,andthenpulloutthecordfromtheleftsideof
thebattery.Attachthebatterytotheshoulderharness
assembly,andthenattachthecordtothecordholders.
1
Fig.11
►1. Cord holder
2. Press the power button on the portable power
pack. The main power lamp will light up.
1
2
Fig.12
►1. Power button 2. Main power lamp
3. Put on the shoulder harness of the portable power
pack and lock the buckle of the waist belt, and lock the
buckleofthechestbelt(forPDC1500only).
Fig.13
4. Attach the hooks of the hanging band to the hang-
ers of the machine.
1
2
1
2
Fig.14
►1. Hook 2. Hanger
NOTE: The hooks at the ends of the blue band are
attached to the machine, and the hook at the end of
the black band is attached to the shoulder harness.
5. Attach the hook of the hanging band to the ring of
the shoulder harness.
1
2
Fig.15
►1. Ring 2. Hook

12 ENGLISH
Adjustthelengthofthehangingbandasnecessary.
Fig.16
6. Insert the plug of the machine into the socket of
the portable power pack.
When inserting the plug into the socket, align the trian-
gle markings on both the plug and the socket.
12
3
Fig.17
►1. Plug 2. Socket 3. Triangle marking
NOTICE: When disconnecting the plug and
socket, do not hold the cords but hold the plug
and socket.Otherwise,thecordsmaybedamaged
and cause a malfunction of the unit.
7. Press the main power switch to turn on the machine.
Themachineisreadytooperate.Themachinewillrun
whenyoupulltheswitchtrigger.
NOTE: Attach the cord of the machine to the cord
holderofthewaistbeltasshowninthegure(for
PDC1500only).
1
Fig.18
►1. Cord holder
Blower operation
CAUTION: Do not place the machine on the
ground while it is switched on.Sandordustmay
enter from suction inlet and cause a malfunction or
personalinjury.
NOTICE: Depending on the attached nozzle, the
recoil to the operator may be large when using the
machine due to the high air force of this product.
Adjust the air speed to an appropriate level when
using the machine.
Holdthemachinermlywithahandandperformthe
blowingoperationbymovingitaroundslowly.Whenblow-
ing around building, big stone or vehicle, direct the nozzle
awayfromthem.Whenperforminganoperationina
corner, start from the corner and then move to wide area.
Fig.19

13 ENGLISH
Setting down the machine
Before setting down the portable power pack, remove
the machine from the portable power pack.
1. Disconnect the plug of the machine and the socket
of the portable power pack.
2. Remove the cord of the machine from the cord
holderofthewaistbelt(forPDC1500only).
3. Remove the hook of the hanging band from the
ring of the shoulder harness with one hand while hold-
ing the machine with the other hand, and then set down
the machine.
4. Unlock the buckle of the chest belt (for PDC1500
only),andunlockthebuckleofthewaistbelt,andthen
setdowntheportablepowerpackslowly.
1
1
Fig.20
►1. Buckle
You can also set down the machine as follows.
1. Disconnect the plug of the machine and the socket
of the portable power pack.
2. Unlock the buckle on the hanging band with one
hand while holding the machine with the other hand.
1
Fig.21
►1. Buckle
MAINTENANCE
CAUTION: Always be sure that the machine is
switched o󰀨 and the portable power pack is dis-
connected from the machine before attempting to
perform inspection or maintenance.
To maintain product SAFETY and RELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
beperformedbyMakitaAuthorizedorFactoryService
Centers,alwaysusingMakitareplacementparts.
Cleaning the machine
Cleanthemachinebywipingo󰀨dustwithadryclothor
onedippedinsoapywaterandwrungout.
Fig.22

14 ENGLISH
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Remove dust or dirt from the suction inlet at the rear of
the machine.
1
Fig.23
►1. Suction inlet
Storage
Before storing the machine, disconnect the portable
power pack from the machine, and perform full main-
tenance. Store the machine in a place out of the reach
of children and not exposed to moisture, rain, or direct
sunlight.
The hook hole on the bottom of the machine is conve-
nient for hanging the machine from a nail or screw on
the wall.
1
Fig.24
►1. Hole
1
Fig.25
►1. Hole

15 ENGLISH
TROUBLESHOOTING
Beforeaskingforrepairs,conductyourowninspectionrst.Ifyoundaproblemthatisnotexplainedintheman-
ual,donotattempttodismantlethemachine.Instead,askMakitaAuthorizedServiceCenters,alwaysusingMakita
replacement parts for repairs.
State of abnormality Probable cause (malfunction) Remedy
Motor does not run. Batteryisnotinstalled. Installthebattery.
Batteryproblem(undervoltage) Rechargethebattery.Ifrechargingisnote󰀨ective,
replacebattery.
Thedrivesystemdoesnotwork
correctly.
Askyourlocalauthorizedservicecenterforrepair.
Motor stops running after a little use. Battery'schargelevelislow. Rechargethebattery.Ifrechargingisnote󰀨ective,
replacebattery.
Overheating. Stop using the machine to allow it to cool down.
The machine does not reach the
maximum speed.
Batteryisinstalledimproperly. Installthebatteryasdescribedinthismanual.
Batterypowerisdropping. Rechargethebattery.Ifrechargingisnote󰀨ective,
replacebattery.
Thedrivesystemdoesnotwork
correctly.
Askyourlocalauthorizedservicecenterforrepair.
Abnormal vibration:
stopthemachineimmediately!
Thedrivesystemdoesnotwork
correctly.
Askyourlocalauthorizedservicecenterforrepair.
Motor cannot stop:
Removethebatteryimmediately!
Electric or electronic malfunction. Removethebatteryandaskyourlocalauthorized
service center for repair.
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita prod-
uct specied in this manual.Theuseofanyother
accessories or attachments might present a risk of
injurytopersons.Onlyuseaccessoryorattachment
for its stated purpose.
Ifyouneedanyassistanceformoredetailsregard-
ingtheseaccessories,askyourlocalMakitaService
Center.
• Adapter pipe
• Flat nozzle
• Makitagenuinebatteryandcharger
NOTE:Someitemsinthelistmaybeincludedinthe
productpackageasstandardaccessories.Theymay
di󰀨erfromcountrytocountry.

Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi 446-8502 Japan
www.makita.com
885A56-921
EN
20230919