Makita DG001G User manual

DG001G
EN Cordless Earth Auger INSTRUCTION MANUAL 5
ZHCN 充电式地钻 使用说明书 13
ID Spiral Bumi Tanpa Kabel PETUNJUK PENGGUNAAN 22
MS Gerimit Bumi Tanpa Kord MANUAL ARAHAN 31
VI Máy Khoan Đất Cầm Tay Hoạt
Động Bằng Pin TÀI LIỆU HƯỚNG DẪN 40
TH   49

1
3 4
5 6
7 8
2
ABC
ABCH
Fig.1
1
1
Fig.2
1
2
3
2
3
Fig.3
2
1
1
2
Fig.4
1
2
Fig.5
1
Fig.6
2

1
Fig.7
1
Fig.8
1
A
B
Fig.9
1
Fig.10
1
2
3
Fig.11
2
3
1
1
Fig.12
1
2
3
Fig.13
3

1
Fig.14
1
2
Fig.15
1
2
Fig.16
1
2
33
2
1
Fig.17
Fig.18
Fig.19
4

5ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model: DG001G
No load speed High 0 - 1,500 min-1
Low 0 - 400 min-1
Drilling capacities
(Diameter)
For sandy soil: ø200 mm
For clay soil: ø150 mm
Overall length 842 mm *1
Rated voltage D.C. 36 V - 40 V max
Net weight 7.2 - 8.1 kg
*1. With side handle and battery cartridge BL4040.
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsmaydi󰀨erfromcountrytocountry.
• Theweightmaydi󰀨erdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge BL4020 / BL4025* / BL4040* / BL4050F*
* : Recommended battery
Charger DC40RA / DC40RB / DC40RC
• Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
andchargersmaycauseinjuryand/orre.
Recommended cord connected power source
Portable power pack PDC01 / PDC1200
• The cord connected power source(s) listed above may not be available depending on your region of residence.
• Before using the cord connected power source, read instruction and cautionary markings on them.
Symbols
The followings show the symbols which may be used
for the equipment. Be sure that you understand their
meaning before use.
Read instruction manual.
Ni-MH
Li-ion
Only for EU countries
Due to the presence of hazardous com-
ponents in the equipment, waste electrical
and electronic equipment, accumulators
and batteries may have a negative impact
on the environment and human health.
Do not dispose of electrical and electronic
appliances or batteries with household
waste!
In accordance with the European Directive
on waste electrical and electronic equip-
ment and on accumulators and batteries
and waste accumulators and batteries,
as well as their adaptation to national law,
waste electrical equipment, batteries and
accumulators should be stored separately
and delivered to a separate collection point
for municipal waste, operating in accor-
dance with the regulations on environmen-
tal protection.
This is indicated by the symbol of the
crossed-out wheeled bin placed on the
equipment.
Intended use
The tool is intended for drilling the ground.

6ENGLISH
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool. Failure to follow all instructions
listedbelowmayresultinelectricshock,reand/or
seriousinjury.
Save all warnings and instruc-
tions for future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiedplugsandmatchingoutletswill
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
6. If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
7. Power tools can produce electromagnetic
elds (EMF) that are not harmful to the user.
However, users of pacemakers and other similar
medical devices should contact the maker of their
device and/or doctor for advice before operating
this power tool.
Personal safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inuence of drugs, alcohol or med-
ication. A moment of inattention while operating
powertoolsmayresultinseriouspersonalinjury.
2. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
willreducepersonalinjuries.
3. Prevent unintentional starting. Ensure the
switch is in the o󰀨-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
yourngerontheswitchorenergisingpowertools
that have the switch on invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
resultinpersonalinjury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts.Looseclothes,jewelleryor
long hair can be caught in moving parts.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
8. Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action
cancausesevereinjurywithinafractionofa
second.
9. Always wear protective goggles to protect
your eyes from injury when using power tools.
The goggles must comply with ANSI Z87.1 in
the USA, EN 166 in Europe, or AS/NZS 1336
in Australia/New Zealand. In Australia/New
Zealand, it is legally required to wear a face
shield to protect your face, too.
It is an employer's responsibility to enforce
the use of appropriate safety protective equip-
ments by the tool operators and by other per-
sons in the immediate working area.

7ENGLISH
Power tool use and care
1. Do not force the power tool. Use the correct
power tool for your application. The correct
powertoolwilldothejobbetterandsaferatthe
rate for which it was designed.
2. Do not use the power tool if the switch does
not turn it on and o󰀨. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
3. Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any adjust-
ments, changing accessories, or storing power
tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
4. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
5. Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may a󰀨ect the power tool’s operation. If dam-
aged, have the power tool repaired before use.
Many accidents are caused by poorly maintained
power tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power tool
foroperationsdi󰀨erentfromthoseintendedcould
result in a hazardous situation.
8. Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpected
situations.
9. When using the tool, do not wear cloth work
gloves which may be entangled. The entangle-
ment of cloth work gloves in the moving parts may
resultinpersonalinjury.
Battery tool use and care
1. Recharge only with the charger specied by
the manufacturer. A charger that is suitable for
onetypeofbatterypackmaycreateariskofre
when used with another battery pack.
2. Use power tools only with specically desig-
nated battery packs. Use of any other battery
packsmaycreateariskofinjuryandre.
3. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery termi-
nalstogethermaycauseburnsorare.
4. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If con-
tact accidentally occurs, ush with water. If
liquid contacts eyes, additionally seek medical
help.Liquidejectedfromthebatterymaycause
irritation or burns.
5. Do not use a battery pack or tool that is dam-
aged or modied.Damagedormodiedbatteries
may exhibit unpredictable behaviour resulting in
re,explosionorriskofinjury.
6. Do not expose a battery pack or tool to re or
excessive temperature.Exposuretoreortem-
perature above 130 °C may cause explosion.
7. Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specied in the instruc-
tions. Charging improperly or at temperatures
outsidethespeciedrangemaydamagethe
batteryandincreasetheriskofre.
Service
1. Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
2. Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
3. Follow instruction for lubricating and chang-
ing accessories.
Cordless Earth Auger safety
warnings
1. Hold the tool with both hands at the intended
handles. Loss of control can cause personal
injury.
2. Brace the tool properly before use. This tool
produces a high output torque and without prop-
erly bracing the tool during operation, loss of
controlmayoccurresultinginpersonalinjury.
3. Hold the power tool by insulated gripping
surfaces, when performing an operation where
the digging accessory may contact hidden
wiring. Digging accessory contacting a “live”
wire may make exposed metal parts of the power
tool “live” and could give the operator an electric
shock.
4. Never operate at higher speed than the maxi-
mum speed rating of the earth augering bit. At
higher speeds, the bit is likely to bend if allowed
to rotate freely without contacting the workpiece,
resultinginpersonalinjury.
5. Always start earth augering at low speed and
with the earth augering tip in contact with the
ground. At higher speeds, the bit is likely to bend
if allowed to rotate freely without contacting the
ground,resultinginpersonalinjury.
6. Apply pressure only in direct line with the bit
and do not apply excessive pressure. Bits can
bend causing breakage or loss of control, resulting
inpersonalinjury.
7. The outside diameter of the auger bit must be
within the drilling capacity specied in this
instruction manual. Incorrectly sized auger bit
cannot be adequately controlled.
8. Always be sure you have a rm footing. Be
sure no one is below when using the tool in
high locations.
9. Hold the tool rmly.
10. Keep hands away from rotating parts.

8ENGLISH
11. Do not leave the tool running. Operate the tool
only when hand-held.
12. Do not touch the auger bit immediately after
operation; it may be extremely hot and could
burn your skin.
13. Some material contains chemicals which may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follow material supplier
safety data.
14. If the auger bit cannot be loosened even you
remove the auger pin, use pliers to pull it out.
In such a case, pulling out the auger bit by hand
mayresultininjurybyitssharpedge.
15. If something wrong with the tool such as
abnormal sounds, stop operating immediately
and ask your local Makita Service Center for
repair.
16. Before operation, make sure that there is no
buried object such as electric pipe, water pipe
or gas pipe in the ground. Otherwise, the tool
may touch them, resulting an electric shock, elec-
trical leakage or gas leak.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
2. Do not disassemble or tamper the battery
cartridge.Itmayresultinare,excessiveheat,
or explosion.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdown.
6. Do not store and use the tool and battery car-
tridge in locations where the temperature may
reach or exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the
battery cartridge. Such conduct may result in a
re,excessiveheat,orexplosion.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Please also observe possibly more detailed
national regulations.
Tapeormasko󰀨opencontactsandpackupthe
battery in such a manner that it cannot move
around in the packaging.
11. When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specied by Makita. Installing the batteries to
non-compliantproductsmayresultinare,exces-
sive heat, explosion, or leak of electrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
14. During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool imme-
diately after use as it may get hot enough to
cause burns.
16. Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge. It may result in poor performance or
breakdown of the tool or battery cartridge.
17. Unless the tool supports the use near
high-voltage electrical power lines, do not use
the battery cartridge near a high-voltage elec-
trical power lines. It may result in a malfunction
or breakdown of the tool or battery cartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causingres,personalinjuryanddamage.Itwill
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.

9ENGLISH
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4. When not using the battery cartridge, remove
it from the tool or the charger.
5. Charge the battery cartridge if you do not use
it for a long period (more than six months).
INITIAL SETTING
CAUTION: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before carrying out any work on the tool.
PARTS DESCRIPTION
►Fig.1
1Main tool 2Front handle
3Side handle 4Reaction receiver
5Bit adapter 6Chuck key
7Bolt 8Wrench
Specications of the bolt / wrench
-Nominal diameter
of the bolt
Wrench size (H)
AM 12 10 mm
BM 8 6 mm
CM 6 5 mm
NOTE: The type of the bit adapter varies depending
on the country.
Setting up the tool
CAUTION: Always be sure that the side
handle and the reaction receiver are installed
securely before operation.
NOTICE: Do not over tighten the bolts. It may
damage the tool.
Installing the side handle
Removetheboltsshowninthegurefromthetool.
The removed bolt is not needed for this tool if you want
to use this tool as a cordless earth auger.
Keep the bolts so that they are not lost.
►Fig.2: 1. Bolt
Place the side handle on the tool.
Tighten the all four bolts temporarily, and then securely
tighten the bolts using the wrench.
►Fig.3: 1. Side handle 2. Bolt A 3. Bolt B
Installing the reaction receiver
Place the reaction receiver so that the bar of the reac-
tion receiver comes to the left side of the operator.
Adjustthepositionofthereactionreceiversothatthe
axis of the drill chuck is in the center of the operator's
body.
Fastentheboltsrmly.
►Fig.4: 1. Bar of the reaction receiver 2. Bolt C
FUNCTIONAL
DESCRIPTION
CAUTION: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before adjusting or checking function on the tool.
Indicating the remaining battery
capacity
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for a few seconds.
►Fig.5: 1. Indicator lamps 2. Check button
Indicator lamps Remaining
capacity
Lighted O󰀨 Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
The battery
may have
malfunctioned.
NOTE: Depending on the conditions of use and the
ambienttemperature,theindicationmaydi󰀨erslightly
from the actual capacity.
NOTE:Therst(farleft)indicatorlampwillblinkwhen
the battery protection system works.
Tool / battery protection system
The tool is equipped with a tool/battery protection sys-
tem.Thissystemautomaticallycutso󰀨powertothe
motor to extend tool and battery life. The tool will auto-
matically stop during operation if the tool or battery is
placed under one of the following conditions:

10 ENGLISH
Overload protection
When the tool/battery is operated in a manner that
causes it to draw an abnormally high current, the tool
stopsautomatically.Inthissituation,turnthetoolo󰀨
and stop the application that caused the tool to become
overloaded. Then turn the tool on to restart.
Overheat protection
When the tool/battery is overheated, the tool stops
automatically. In this situation, let the tool/battery cool
before turning the tool on again.
Overdischarge protection
When the battery capacity is not enough, the tool stops
automatically. In this case, remove the battery from the
tool and charge the battery.
Main power switch
WARNING: Always turn o󰀨 the main power
switch when not in use.
To stand by the tool, press the main power button until
themainpowerlamplightsup.Toturno󰀨,pressthe
main power button again.
►Fig.6: 1. Main power button
NOTE:Thistoolemploystheautopower-o󰀨function.
To avoid unintentional start up, the main power switch
will automatically shut down when the switch trigger
is not pulled for a certain period after the main power
switch is turned on.
Switch action
CAUTION: Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the “OFF” position when released.
►Fig.7: 1. Switch trigger
To start the tool, pull the switch trigger with the main
power switch on. Tool speed is increased by increas-
ing pressure on the switch trigger. Release the switch
trigger to stop.
NOTE: The tool automatically stops if you keep pull-
ing the switch trigger for about 6 minutes.
Lighting up the front lamp
CAUTION: Do not look in the light or see the
source of light directly.
►Fig.8: 1. Lamp
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The lamp goes out approximately 10 seconds after
releasing the switch trigger.
NOTE: When the tool is overheated, the tool stops
automaticallyandthelampstartsashing.Inthis
case,releasetheswitchtrigger.Thelampturnso󰀨in
5 minute(s).
NOTE:Useadryclothtowipethedirto󰀨thelensof
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
Reversing switch action
CAUTION: Always check the direction of
rotation before operation.
CAUTION: Use the reversing switch only after
the tool comes to a complete stop. Changing the
direction of rotation before the tool stops may dam-
age the tool.
CAUTION: When not operating the tool,
always set the reversing switch lever to the neu-
tral position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for coun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion, the switch lever cannot be pulled.
►Fig.9: 1. Reversing switch lever
Automatic speed change function
This tool has “high speed mode” and “high torque
mode”.
The tool automatically changes the operation mode
depending on the work load. When the work load is low,
the tool will run in the “high speed mode” for quicker
operation. When the work load is high, the tool will run
in the “high torque mode” for powerful operation.
►Fig.10: 1. Mode indicator
The mode indicator lights up in green when the tool is
running in “high torque mode”.
If the tool is operated with excessive load, the mode
indicator will blink in green. The mode indicator stops
blinkingandthenlightsuporturnso󰀨ifyoureducethe
load on the tool.
Mode indicator status Operation
mode
On O󰀨 Blinking
High speed
mode
High torque
mode
Overload
alert

11 ENGLISH
Speed change
NOTICE: Use the tool at low speed (position 1).
Otherwise the digging operation may not be able to
completeduetoinsu󰀩cienttorque.
NOTICE: Use the speed change knob only after
the tool comes to a complete stop. Changing the
tool speed before the tool stops may damage the tool.
NOTICE: Always set the speed change knob
carefully into the correct position. If you operate
the tool with the speed change knob positioned half-
way between the position 1 and the position 2, the
tool may be damaged.
Two speed ranges can be preselected with the speed
change knob.
To change the speed, depress the lock button and turn
the speed change knob so that the pointer points to the
position 1 for low speed or the position 2 for high speed.
►Fig.11: 1. Lock button 2. Pointer 3. Speed change
knob
Torque limiter
The torque limiter will actuate when a certain torque
level is reached at the low speed setting (position 1).
The motor will disengage from the output shaft. When
this happens, the tool bit will stop turning.
To restart the tool, lift the tool bit out of the hole and
then pull the switch trigger again.
Electronic function
Electric brake
This tool is equipped with an electric brake. If the tool
consistently fails to quickly cease to function after the
switch trigger is released, have the tool serviced at a
Makita service center.
Soft start feature
This function allows the smooth start-up of the tool by
limiting the start-up torque.
ASSEMBLY
Installing or removing battery
cartridge
CAUTION: Always switch o󰀨 the tool before
installing or removing of the battery cartridge.
CAUTION: Hold the tool and the battery car-
tridge rmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridgermlymaycausethemtoslipo󰀨yourhands
and result in damage to the tool and battery cartridge
andapersonalinjury.
►Fig.12: 1. Red indicator 2. Button 3. Battery
cartridge
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator as
showninthegure,itisnotlockedcompletely.
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
itmayaccidentallyfalloutofthetool,causinginjuryto
you or someone around you.
CAUTION: Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
Mounting the auger bit
CAUTION: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION: When installing the bit adapter to
the chuck, make sure that the bit adapter is fully
inserted.
CAUTION: When attaching the auger bit to the
bit adapter, make sure that the auger pin is locked
and inspect the auger pin for any damages.
CAUTION: When carrying the tool, remove
the auger bit from the tool.
Installing or removing the bit adapter
To mount the auger bit, install the bit adapter in
advance.
To install the bit adapter, place the bit adapter in the
chuck as far as it will go. Tighten the chuck by rotating
the sleeve by hand.
Place the chuck key in the chuck hole and tighten clock-
wise. Be sure to tighten all three chuck holes evenly.
To remove the bit adapter, turn the chuck key counter-
clockwiseinjustonehole,thenloosenthechuckby
hand.
►Fig.13: 1. Chuck key 2. Chuck 3. Sleeve
After use, return the chuck key to the key holder on the
tool as illustrated.
►Fig.14: 1. Key holder
Mounting the auger bit on the bit
adapter
NOTE: The shape and mechanism of the auger bit
and the auger pin may vary depending on your auger
bit.
Align the hole on the bit adapter with the hole on the
auger bit.
Put the auger bit onto the bit adapter.
►Fig.15: 1. Auger bit 2. Bit adapter
Fix the auger bit with the auger pin and the safety lock.
►Fig.16: 1. Auger pin 2. Safety lock

12 ENGLISH
OPERATION
CAUTION: This is a powerful tool which gen-
erates high torque. It is important that the tool is
securely held and properly braced.
CAUTION: Before operating, check that there
is no foreign matter (sand, dirt, etc.) stuck in the
openings or moving parts.
Work posture
Maintaining proper operating position is one of the
mostimportantande󰀨ectiveproceduresforcontrolling
kickback.
Keep proper positioning by practicing the following
points.
• Position the tool so that the bar of the reaction
receiver always contacts on the left side of your
waist.
• Grasp the handle and the side handle with both
hands.Wrapyourngersaroundthegripping
areas, keeping the gripping areas cradled
betweenyourthumbsandforengers.
• Keep your back as vertical as possible by bending
the legs as required during the digging process.
• Stay alert to the torque reaction force of the tool.
Always keep the operating position that you can
withstand the torque reaction force.
►Fig.17: 1. Handle 2. Side handle 3. Bar of the reac-
tion receiver
WARNING: Avoid improper positioning. Do
not stand too far from the tool. Proper reaction and
control may not be achieved in the event of kickback.
►Fig.18
Digging operation
CAUTION: Hold the tool rmly when operat-
ing the tool.
CAUTION: When leaving the tool, such as
during a break, do not leave the tool stabbed in
the ground or lean it against a wall. Store the tool
in a stable condition.
NOTICE: When the rotation speed comes down
extremely, reduce the load or stop the tool to
avoid the tool damage.
NOTICE: Pressing excessively on the tool will
not speed up the digging. In fact, this excessive
pressure will only serve to damage the tip of the
auger bit, decrease the tool performance and shorten
the service life of the tool.
NOTICE: Avoid digging in material that you
suspect contains hidden nails or other things that
may cause the auger bit to bind or break.
NOTICE: If the tool is operated continuously
until the battery cartridge has depleted, allow the
tool to rest for 15 minutes before proceeding with
a fresh battery.
• When digging a deep hole or digging in clay soil,
do not try to dig at once. Dig the hole by lifting up
and down the tool so that the soil in the hole can
be discharged.
• If the rotation speed of the tool slows down due to
high load operation, lift the tool up little, and move
the tool up and down to dig in small steps.
When rotating the auger bit in
reverse
A stuck auger bit can be removed simply by setting the
reversing switch to reverse rotation in order to back out.
When reversing, brace the tool by your body to prevent
a clockwise reaction.
►Fig.19
CAUTION: Hold the tool rmly. The tool may
backoutabruptlyandcauseaninjury.
MAINTENANCE
CAUTION: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita tool
specied in this manual. The use of any other
accessories or attachments might present a risk of
injurytopersons.Onlyuseaccessoryorattachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Auger bits
• Bit adapter
• Handle set
• Makita genuine battery and charger
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
di󰀨erfromcountrytocountry.

13
中文简体
中文简体 (原本)
规格
型号： DG001G
空载速度 高0 - 1,500 r/min
低0 - 400 r/min
钻孔能力
（直径）
对于砂土：ø200 mm
对于粘土：ø150 mm
总长度 842 mm *1
额定电压 D.C. 36 V - 40 V（最大）
净重 7.2 - 8.1 kg
*1.配置侧手柄和电池组BL4040。
• 生产者保留变更规格不另行通知之权利。
• 规格可能因销往国家之不同而异。
• 重量因附件（包括电池组）而异。根据EPTA-Procedure 01/2014，最重与最轻的组合见
表格。
适用电池组和充电器
电池组 BL4020 / BL4025* / BL4040* / BL4050F*
*：建议使用的电池
充电器 DC40RA / DC40RB / DC40RC
• 部分以上所列电池组和充电器是否适用视用户所在地区而异。
警告： 请仅使用以上所列电池组和充电器。使用其他类型的电池组或充电器可能会导
致人身伤害和/或失火。
推荐的用电源线连接的电源
便携电源装置 PDC01 / PDC1200
• 以上所列的用电源线连接的电源是否适用取决于用户所在地区。
• 在使用用电源线连接的电源之前，请先阅读使用说明和了解相关警示标识。

14
中文简体
符号
以下显示本设备可能会使用的符号。在使用
工具之前，请务必理解其含义。
阅读使用说明书。
Ni-MH
Li-ion 仅限于欧盟国家
由于本设备中包含有害成分，
因此废弃的电气和电子设备、
蓄电池和普通电池可能会对环
境和人体健康产生负面影响。
请勿将电气和电子工具或电池
与家庭普通废弃物放在一起处
置！
根据欧洲关于废弃电气电子设
备、蓄电池和普通电池、废弃
的蓄电池和普通电池的指令及
其国家层面的修订法案，废弃
的电气设备、普通电池和蓄电
池应当单独存放并递送至城市
垃圾收集点，根据环保法规进
行处置。
此规定由标有叉形标志的带轮
垃圾桶符号表示。
用途
本工具用于对地面钻孔。
安全警告
电动工具通用安全警告
警告： 阅读随电动工具提供的所有安全
警告、说明、图示和规定。不遵照以下所列
说明会导致电击、着火和／或严重伤害。
保存所有警告和说明书以备
查阅。
警告中的术语“电动工具”是指市电驱动
（有线）电动工具或电池驱动（无线）电动
工具。
工作场地的安全
1. 保持工作场地清洁和明亮。杂乱和黑暗
的场地会引发事故。
2. 不要在易爆环境，如有易燃液体、气体
或粉尘的环境下操作电动工具。电动工
具产生的火花会点燃粉尘或气体。
3. 操作电动工具时，远离儿童和旁观者。注
意力不集中会使你失去对工具的控制。
电气安全
1. 电动工具插头必须与插座相配。绝不能
以任何方式改装插头。需接地的电动工
具不能使用任何转换插头。未经改装的
插头和相配的插座将降低电击风险。
2. 避免人体接触接地表面，如管道、散热
片和冰箱。如果你身体接触接地表面会
增加电击风险。
3. 不得将电动工具暴露在雨中或潮湿环境
中。水进入电动工具将增加电击风险。
4. 不得滥用软线。绝不能用软线搬运、拉
动电动工具或拔出其插头。使软线远离
热源、油、锐边或运动部件。受损或缠
绕的软线会增加电击风险。
5. 当在户外使用电动工具时，使用适合户
外使用的延长线。适合户外使用的电线
将降低电击风险。
6. 如果无法避免在潮湿环境中操作电动工
具，应使用带有剩余电流装置（RCD）
保护的电源。RCD的使用可降低电击
风险。
7. 电动工具会产生对用户无害的电磁场
（EMF）。但是，起搏器和其他类似医
疗设备的用户应在操作本电动工具前咨
询其设备的制造商和／或医生寻求建议。
人身安全
1. 保持警觉，当操作电动工具时关注所从
事的操作并保持清醒。当你感到疲倦，
或在有药物、酒精或治疗反应时，不要
操作电动工具。在操作电动工具时瞬间
的疏忽会导致严重人身伤害。
2. 使用个人防护装置。始终佩戴护目镜。
防护装置，诸如适当条件下使用防尘面
具、防滑安全鞋、安全帽、听力防护等
装置能减少人身伤害。
3. 防 止 意 外 起 动 。在 连 接 电 源 和 /或电池包、
拿起或搬运工具前确保开关处于关断位
置。手指放在开关上搬运工具或开关处于
接通时通电会导致危险。
4. 在电动工具接通之前，拿掉所有调节钥
匙或扳手。遗留在电动工具旋转零件上
的扳手或钥匙会导致人身伤害。
5. 手不要过分伸展。时刻注意立足点和身
体平衡。这样能在意外情况下能更好地
控制住电动工具。
6. 着装适当。不要穿宽松衣服或佩戴饰品。
让你的头发和衣服远离运动部件。宽松衣
服、佩饰或长发可能会卷入运动部件。

15
中文简体
7. 如果提供了与排屑、集尘设备连接用的
装置，要确保其连接完好且使用得当。
使用集尘装置可降低尘屑引起的危险。
8. 不要因为频繁使用工具而产生的熟悉感而
掉以轻心，忽视工具的安全准则。某个粗
心的动作可能在瞬间导致严重的伤害。
9. 使用电动工具时请始终佩带护目镜以免伤
害眼睛。护目镜须符合美国ANSI Z87.1、
欧洲EN 166或者澳大利亚／新西兰的AS/
NZS 1336的规定。在澳大利亚／新西兰，
法律要求佩带面罩保护脸部。
雇主有责任监督工具操作者和其他近工
作区域人员佩带合适的安全防护设备。
电动工具使用和注意事项
1. 不要勉强使用电动工具，根据用途使用
合适的电动工具。选用合适的按照额定
值设计的电动工具会使你工作更有效、
更安全。
2. 如果开关不能接通或关断电源，则不能
使用该电动工具。不能通过开关来控制
的电动工具是危险的且必须进行修理。
3. 在进行任何调节、更换附件或贮存电动
工具之前，必须从电源上拔掉插头和/或
卸下电池包（如可拆卸）。这种防护性
的安全措施降低了电动工具意外起动的
风险。
4. 将闲置不用的电动工具贮存在儿童所及
范围之外，并且不允许不熟悉电动工具
和不了解这些说明的人操作电动工具。
电动工具在未经培训的使用者手中是危
险的。
5. 维护电动工具及其附件。检查运动部件是
否调整到位或卡住，检查零件破损情况和
影响电动工具运行的其他状况。如有损
坏，应在使用前修理好电动工具。许多
事故是由维护不良的电动工具引发的。
6. 保持切削刀具锋利和清洁。维护良好地
有锋利切削刃的刀具不易卡住而且容易
控制。
7. 按照使用说明书，并考虑作业条件和要
进行的作业来选择电动工具、附件和工
具的刀头等。将电动工具用于那些与其
用途不符的操作可能会导致危险情况。
8. 保持手柄和握持表面干燥、清洁，不得
沾有油脂。在意外的情况下，湿滑的手
柄不能保证握持的安全和对工具的控制。
9. 使用本工具时，请勿佩戴可能会缠结的
布质工作手套。布质工作手套卷入移动
部件可能会造成人身伤害。
电池式工具使用和注意事项
1. 仅使用生产者规定的充电器充电。将适
用于某种电池包的充电器用到其他电池
包时可能会发生着火危险。
2. 仅使用配有专用电池包的电动工具。使用
其他电池包可能会产生伤害和着火危险。
3. 当电池包不用时，将它远离其他金属物
体，例如回形针、硬币、钥匙、钉子、
螺钉或其他小金属物体，以防电池包一
端与另一端连接。电池组端部短路可能
会引起燃烧或着火。
4. 在滥用条件下，液体可能会从电池组中溅
出；应避免接触。如果意外碰到液体，
用水冲洗。如果液体碰到了眼睛，还应
寻求医疗帮助。从电池中溅出的液体可
能会发生腐蚀或燃烧。
5. 不要使用损坏或改装过的电池包或工具。
损坏或改装过的电池组可能呈现无法预测
的结果，导致着火、爆炸或伤害。
6. 不要将电池包暴露于火或高温中。电池
包暴露于火或高于130 ℃的高温中可能
导致爆炸。
7. 遵循所有充电说明。不要在说明书中指
定的温度范围之外给电池包或电动工具
充电。不正确或在指定的温度范围外充
电可能会损坏电池和增加着火的风险。
维修
1. 让专业维修人员使用相同的备件维修电
动工具。这将保证所维修的电动工具的
安全。
2. 决不能维修损坏的电池包。电池包仅能由
生产者或其授权的维修服务商进行维修。
3. 上润滑油及更换附件时请遵循本说明书
指示。

16
中文简体
充电式地钻安全警告
1. 使用辅助手柄。失控会导致人身伤害。
2. 工具使用前应得到适当支撑。由于工具
输出转矩大，运行时没有适当支撑会失
控导致人身伤害。
3. 当在钻削附件可能触及暗线的场合进行
操作时，通过绝缘握持面握持工具。钻
削附件碰到带电导线会使工具外露金属
零件带电而使操作者遭受电击。
4. 操作时的速度不得高于地钻钻头的最大
额定速度。在高速状态下，若钻头不接
触工件空转，则钻头可能会弯曲，进而
造成人身伤害。
5. 务必在低速条件下启动地钻，并使地钻钻
头的尖端与地面接触。在 高 速 状 态 下，若 钻
头 不 接 触 地 面 空 转 ，则 钻 头 可 能 会 弯 曲 ，进
而造成人身伤害。
6. 只在与钻头成一直线的位置施加压力，切
勿过度施压。否则钻头可能弯曲，导致破
损或失控，从而造成人身伤害。
7. 螺旋钻头的外直径必须位于此使用说明
书中规定的钻孔范围内。若螺旋钻头尺
寸不当，将无法对其安全操控。
8. 请务必确保立足稳固。在高处使用工具
时确保下方无人。
9. 请牢握本工具。
10. 手应远离旋转的部件。
11. 运行中的工具不可离手放置。只可在手
握工具的情况下操作工具。
12. 操作之后螺旋钻头温度可能非常高，此
时请勿立刻触碰螺旋钻头，否则可能会
烫伤皮肤。
13. 某些材料含有有毒化学物质。小心不要
吸入粉尘，并避免皮肤接触。遵循材料
供应商的安全提示。
14. 如果拆除螺旋钻头销钉后依然无法拧松
螺旋钻头，请使用虎钳将其拉出。在这
种情况下，徒手拉出螺旋钻头可能会被
尖锐的边缘划伤。
15. 若工具出现声音异常等问题，请立即停
止使用，并交由当地Makita（牧田）授
权的维修服务中心进行维修。
16. 操作前，请务必保证地面内无埋藏物，
例如电气配管、水管或气体管。否则，
工具会触及上述部件，引发触电、漏电
或漏气。
请保留此说明书。
警告： 请勿为图方便或因对产品足够
熟悉（由于重复使用而获得的经验）而不
严格遵循相关产品安全规则。使用不当或
不遵循使用说明书中的安全规则会导致严
重的人身伤害。
电池组的重要安全注意事项
1. 在使用电池组之前，请仔细通读所有的说
明 以 及（ 1） 电 池 充 电 器 ，（ 2）电 池 ，以 及
（3）使用电池的产品上的警告标记。
2. 切勿拆卸或改装电池组。否则可能引起
火灾、过热或爆炸。
3. 如果机器运行时间变得过短，请立即停
止使用。否则可能会导致过热、起火甚
至爆炸。
4. 如果电解液进入您的眼睛，请用清水将
其冲洗干净并立即就医。否则可能会导
致视力受损。
5. 请勿使电池组短路：
(1) 请勿使任何导电材料碰触到端子。
(2) 避免将电池组与其他金属物品如钉
子、硬币等放置在同一容器内。
(3) 请勿将电池组置于水中或使其淋雨。
电池短路将产生大的电流，导致过热，
并可能导致起火甚至击穿。
6. 请勿在温度可能达到或超过50°C（122°F）
的场所存放以及使用工具和电池组。
7. 即使电池组已经严重损坏或完全磨损，也
请勿焚烧电池组。电池组会在火中爆炸。
8. 请勿对电池组射钉，或者切削、挤压、抛
掷、掉落电池组，又或者用硬物撞击电池
组。否则可能引起火灾、过热或爆炸。
9. 请勿使用损坏的电池。
10. 本工具附带的锂离子电池需符合危险品
法规要求。
第三方或转运代理等进行商业运输时，
应遵循包装和标识方面的特殊要求。
有关运输项目的准备作业，咨询危险品
方面的专业人士。同时，请遵守可能更
为详尽的国家法规。
请使用胶带保护且勿遮掩表面的联络信
息，并牢固封装电池，使电池在包装内
不可动。
11. 丢弃电池组时，需将其从工具上卸下并
在安全地带进行处理。关于如何处理废
弃的电池，请遵循当地法规。
12. 仅将电池用于Makita（牧田）指定的产
品。将电池安装至不兼容的产品会导致
起火、过热、爆炸或电解液泄漏。

17
中文简体
13. 如长时间未使用工具，必须将电池从工
具内取出。
14. 使用工具期间以及使用工具之后，电池
组温度可能较高易引起灼伤或低温烫
伤。处理高温电池组时请小心操作。
15. 在使用工具后请勿立即触碰工具的端子，
否则可能引起灼伤。
16. 避免锯屑、灰尘或泥土卡入电池组的端
子、孔口和凹槽内。否则可能导致工具
或电池组性能下降或故障。
17. 除非工具支持在高压电源线路附近使用，
否则请勿在高压电源线路附近使用电池
组。否则可能导致工具或电池组故障或
失常。
18. 确保电池远离儿童。
请保留此说明书。
小心： 请仅使用Makita（牧田）原装电
池。使用非Makita（牧田）原装电池或经过
改装的电池可能会导致电池爆炸，从而造成
火灾、人身伤害或物品受损。同时也会导致
牧田工具和充电器的牧田保修服务失效。
保持电池最大使用寿命的提示
1. 在电池组电量完全耗尽前及时充电。发
现工具电量低时，请停止工具操作，并
给电池组充电。
2. 请勿对已充满电的电池组重新充电。过
度充电将缩短电池的使用寿命。
3. 请在10 °C - 40 °C（50 °F - 104 °F）的
室温条件下给电池组充电。请在灼热的
电池组冷却后再充电。
4. 不使用电池组时，请将其从工具或充电
器上拆除。
5. 如果电池组长时间（超过六个月）未使
用，请给其充电。
初始设置
小心： 对工具进行任何装配操作前，请
务必关闭工具电源，并取出电池组。
部件说明
►图片1
1主工具 2前把手
3侧手柄 4反作用力接收器
5钻头转接头 6卡盘键
7螺栓 8扳手
螺栓/扳手规格
-螺栓标称
直径
扳手规格 (H)
AM 12 10 mm
BM 8 6 mm
CM 6 5 mm
注： 钻头转接头的类型因国家不同而异。
装配工具
小心： 在进行操作之前，请务必将侧手
柄和反作用力接收器安装牢固。
注意： 请勿过度拧紧螺栓。这可能会损坏
工具。
安装侧手柄
拆下图示中工具上的螺栓。
将此工具作为充电式地钻使用时，不需要使
用拆下的螺栓。
请妥善保存这些螺栓以避免遗失。
►图片2: 1. 螺栓
将侧手柄放置在工具上。
暂时将四个螺栓全部拧紧，然后使用扳手将
螺栓紧固。
►图片3: 1. 侧手柄 2. 螺栓A 3. 螺栓B
安装反作用力接收器
放置反作用力接收器，并确保反作用力接收
器杆位于操作员左侧。
调节反作用力接收器位置，使钻机卡盘轴位
于操作员身体的中心位置。
将螺栓牢固锁紧。
►图片4: 1. 反作用力接收器杆 2. 螺栓C

18
中文简体
功能描述
小心： 调节或检查工具功能之前，请务
必关闭工具的电源并取出电池组。
显示电池的剩余电量
按电池组上的CHECK（查看）按钮可显示电
池剩余电量。指示灯将亮起数秒。
►图片5: 1. 指示灯 2. CHECK（查看）
按钮
指示灯 剩余电量
点亮 熄灭 闪烁
75%至
100%
50%至
75%
25%至
50%
0%至
25%
给电池
充电。
电池可
能出现
故障。
注： 在不同的使用条件及环境温度下，指
示灯所示电量可能与实际情况略有不同。
注： 当电池保护系统启动时，第一个（最
左侧）指示灯将闪烁。
工具／电池保护系统
本工具配备有工具／电池保护系统。该系统可
自动切断电机电源以延长工具和电池寿命。作
业时，如果工具或电池处于以下情况，工具将
会自动停止运转。
过载保护
以导致异常高电流的方式操作工具／电池时，
工具会自动停止运转。在这种情况下，请关闭
工具并停止导致工具过载的应用操作。然后开
启工具重新启动。
过热保护
工具／电池过热时，工具会自动停止。在这种
情况下，请待工具／电池冷却后再开启工具。
过放电保护
电池电量不足时，本工具自动停止运转。此
时，请取出工具中的电池并予以充电。
主电源开关
警告： 不使用时，务必关闭主电源开关。
要使工具待机，请按主电源按钮直至主电源指
示灯亮起。要关闭时，请再次按主电源按钮。
►图片6: 1. 主电源按钮
注：本工具采用自动关机功能。为避免意外
启动，在打开主电源开关后的一段时间内未
扣动开关扳机时，主电源开关将自动关闭。
开关操作
小心： 在将电池组插入工具之前，请务
必检查开关扳机是否能扣动自如，松开时能
否退回至“OFF”（关闭）位置。
►图片7: 1. 开关扳机
要启动工具时，请在打开主电源开关的情况
下扣动开关扳机。随着在开关扳机上施加压
力的增大，工具速度会提高。松开开关扳机
工具即停止。
注： 如果持续扣动开关扳机约6分钟，机器
将自动停止。
点亮前灯
小心： 请勿直视灯光或光源。
►图片8: 1. 照明灯
扣动开关扳机点亮照明灯。在扣动开关扳机
期 间 此 灯 保 持 常 亮 。松 开 开 关 扳 机 约 10秒后，
灯将熄灭。
注： 工具过热时，工具将自动停止运转且灯
开 始 闪 烁 。在 这 种 情 况 下 ，请 松 开 开 关 扳 机 。
照明灯将会在5分钟内熄灭。
注： 请使用干布擦拭灯头灰。注意不要刮
花灯头，否则会降低亮度。

19
中文简体
反转开关的操作
小心： 操作前请务必确认工具的旋转
方向。
小心： 只有当工具完全停止转动后方可
使用反转开关。如果在工具停止之前改变旋
转方向，可能会损坏工具。
小心： 不使用工具时，请务必将反转切
换柄置于空档位置。
本 工 具 设 有 反 转 开 关 ，可 改 变 旋 转 方 向 。自 A侧
按压反转切换柄可进行顺时针方向旋转；自B侧
按压则进行逆时针方向旋转。
当反转切换柄在中间位置时，无法扣动开关
柄。
►图片9: 1. 反转切换柄
自动变速功能
本工具设有“高速模式”和“高转矩模式”。
本工具可根据工作负荷自动改变操作模式。工
作负荷 较低 时，本工具 以“高 速模 式 ”运 转，进行
快速操作。工作负荷较高时，本工具则以“高
转矩模式”运转，进行强力操作。
►图片10: 1. 模式指示灯
当本工具以“高转矩模式”运转时，模式指
示灯呈绿色亮起。
工具过载操作时，模式指示灯呈绿色闪烁。降
低工具上的负载后，模式指示灯停止闪烁，然
后亮起或熄灭。
模式指示灯状态 操作模式
亮起 熄灭 闪烁
高速模式
高转矩
模式
过载警告
变速
注意： 请 务 必 在 低 速 下（ 位 置 1）使 用 工 具 。
否则将由于扭矩不足无法完成挖掘操作。
注意： 请在工具完全停止后使用变速钮。在
工具停止前改变工具速度可能会损坏工具。
注意： 请务必小心将变速钮置于正确位置。
在变速钮处于位置1与位置2之间的半位时操
作工具，会使工具受损。
使用变速钮可以预选两种速度范围。
要改变速度时，请按锁定按钮并转动变速钮，
使指针指向位置1进行低速操作，或指向位置
2进行高速操作。
►图片11: 1. 锁定按钮 2. 指针 3. 变速钮
扭矩限制器
当扭矩在低速设定（位置1）下达到一定的水
平时，扭矩限制器将会启动。电机会从输出
轴脱离。这时工具钻头将会停止旋转。
若要重启工具，请将工具钻头从孔中取出，
然后重新拉动开关扳机。
电子功能
电动制动器
本工具配备有电动制动器。如果在松开开关
扳机后，工具始终无法立即停止运作，请交
由Makita（牧田）维修中心进行维修。
软启动功能
该功能可限制启动转矩，实现工具的顺利启
动。

20
中文简体
装配
安装或拆卸电池组
小心： 安装或拆卸电池组之前，请务必
关闭工具电源。
小心： 安装或拆卸电池组时请握紧工具
和电池组。否 则 它 们 可 能 从 您 的 手 中 滑 落 ，导
致工具和电池组受损，甚至造成人身伤害。
►图片12: 1. 红色指示器 2. 按钮 3. 电池组
拆卸电池组时，按下电池组前侧的按钮，同
时将电池组从工具中抽出。
安装电池组时，要将电池组上的舌簧与外罩上
的凹槽对齐，然后推滑到位。将其完全插入到
位，直到锁定并发出咔哒声为止。若能看到图
示中的红色指示器，则说明未完全锁紧。
小心： 务必完全装入电池组，直至看不
见红色指示器为止。否则，它可能会从工具
中意外脱落，从而造成自身或他人受伤。
小心： 请勿强行安装电池组。如果电池
组难以插入，可能是插入方法不当。
安装螺旋钻头
小心： 对工具进行任何装配操作前，请
务必关闭工具电源，并取出电池组。
小心： 将钻头转接头安装在卡盘上时，
确保钻头转接头完全嵌入对应位置。
小心： 将螺旋钻头安装在钻头转接头上
时，确保螺旋钻头销钉已锁定，并检查螺旋
钻头销钉有无损坏。
小心： 搬运工具时，请拆下工具上的螺
旋钻头。
安装或拆下钻头转接头
若要安装螺旋钻头，请提前安装钻头转接头。
若要安装钻头转接头，应将钻头转接头装入
卡盘并尽可能将其推至底部。用手转动套筒
将卡盘拧紧。
将卡盘键放入卡盘孔中并顺时针拧紧。请务
必均匀旋紧三个卡盘孔。
拆下钻头转接头时，将卡盘键插入一个孔中
并逆时针旋转，然后用手拧松卡盘。
►图片13: 1. 卡盘键 2. 卡盘 3. 套筒
使用后，请将卡盘键放回至如图所示的工具
上的卡盘键固定座。
►图片14: 1. 卡盘键固定座
将螺旋钻头安装在钻头转接头上
注： 螺旋钻头和销钉的形状和工作机制可
能因螺旋钻头不同而异。
将钻头转接头上的孔与螺旋钻头上的孔对齐。
将螺旋钻头置于钻头转接头上。
►图片15: 1. 螺旋钻头 2. 钻头转接头
利用螺旋钻头销钉和安全锁将螺旋钻头固定。
►图片16: 1. 螺旋钻头销钉 2. 安全锁
操作
小心： 本工具是一种可产生大扭矩的强
力工具。操作过程中牢固抓持并妥善支撑工
具非常重要。
小心： 操作前，请检查孔口处或移动部
件内部有无异物（沙子、污垢等）卡住。
工作姿势
保持正确的操作位置是有效控制工具反弹的
最重要方式之一。
请遵照以下要点练习，保持适当位置。
• 摆放工具时确保反作用力接收器杆始终
与操作员腰部左侧接触。
• 双手抓握把手和侧手柄。手指包住握持区
域，同时用拇指和食指握紧握持区域。
• 在挖掘过程中根据需要弯曲双腿，同时
尽可能保持背部挺直。
• 时刻注意工具扭矩的反作用力。同时确
保工作位置能够承受扭矩的反作用力。
►图片17: 1. 把手 2. 侧手柄 3. 反作用力
接收器杆
警告： 注意避免工作位置不当。站立位
置不得距离工具过远。否则工具反弹时无法
采取正确的措施并控制反作用力。
►图片18