Makita DUT130 User manual

EN
Cordless Mixer
INSTRUCTION MANUAL
5

2

3
Fig.3
2
Fig.7
Fig.4
Fig.8
Fig.12
B
1
2
1
2
3

4
Fig.9
Fig.13
1
Fig.10
Fig.11
Fig.15
1
2
1
2
1
2

5
Fig.16

6 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model:
DUT130
DUT131
No load speed
High speed
0 - 1,300 min-1
Low speed
0 - 350 min-1
Maximum mixing blade diameter
165 mm
Overall length (without shaft and mixing blade)
320 mm
307 mm
Rated voltage
D.C. 18 V
Net weight
2.5 - 2.8 kg
2.7 - 3.0 kg
•Due to our continuing program of research and development,
the specifications herein are subject to change without
notice.
•Specifications and battery cartridge may differ from country to
country.
•The weight may differ depending on the attachment(s), including
the battery cartridge. The lightest and heaviest combination, according to
EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
Charger
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF
•Someof the battery cartridges and chargers listed above may
not be available depending on your region of residence.
WARNING: Only use the battery cartridges and chargers listed above. Use of any
other battery cartridges and chargers may cause injury and/or
fire.
Symbols
The followings show the symbols
used for the equipment.Be
sure that you understandtheir
meaning before use.

7 ENGLISH
material!
In observance of the European Directives,
on Waste Electric and Electronic
Equipment and Batteries
and Accumulators
and Waste Batteries and
Accumulators and their implementation in
accordance with national laws,
electric equipment and
batteries and battery
pack(s) that have
reached the end of their life must be
collected separately and
returned to an
environmentally
compatible recycling facility.
Intended use
The tool is intended for mixing wall materials, etc.
(except flammable materials).
Noise
The typical A-weightednoise level
determinedaccording to EN60745-2-1:
Model DUT130
Sound pressure level (LpA) : 74 dB(A)
Uncertainty(K) : 3 dB(A)
Model DUT131
Sound pressure level (LpA) : 74 dB(A)
Uncertainty(K) : 3 dB(A)
The noise level under working
may exceed 80 dB (A).
NOTE: The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for
comparing one tool with
another.
NOTE: The declared noise emission
value(s) may also be
used in a
preliminary assessment of
exposure.
WARNING: Wear ear protection.
WARNING: The noise emission during actual
use of the power tool can differ fromthe declared
value(s) depending on the ways in which the tool
is used especially what kind of workpiece is
processed.
WARNING: Be sure to identify safety
measures to protect the operator that are based
on an estimation of exposure in the actual
conditions of use (taking account of all parts of
the operating cycle such as the times when the
tool is switched off and when it is running idle in
addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum)
determined according to EN60745-2-1:
Model DUT130
Work mode: operation without load
Vibration emission (ah) : 2.5 m/s2or less
Uncertainty(K) : 1.5 m/s2
Model DUT131
Work mode: operation without load
Vibration emission (ah) : 2.5 m/s2or less
Uncertainty(K) : 1.5 m/s2
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for
comparing one tool with
another.
NOTE: The declared vibration total
value(s) may also be
used in a
preliminary assessment of
exposure.
WARNING: The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING: Be sure to identify safety
measures to protect the operator that are based
on an estimation of exposure in the actual
conditions of use (taking account of all parts of
the operating cycle such as the times when the
tool is switched off and when it is running idle in
addition to the trigger time).
EC Declaration of Conformity
For European countries only
The EC declarationof conformity
is included as Annex A
to this instruction manual.
Read instruction manual.
Do not use the tool in the rain.
Do not clean the tool with water.
Ni-MH
Li-ion
Only for
EU
Do not dispose of
electric equipment or
battery pack together with
household waste

8 ENGLISH
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool. Failure to follow all
instructions listed below may result in
electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in
the warnings refers to your
mains-operated (corded) power tool
or battery-operated (cordless) power tool.
Cordless mixer safety warnings
1. Hold the tool with both hands at the intended
handles. Loss of control
can cause personal injury.
2. Ensure sufficient ventilation when mixing
flammable materials to avoid a hazardous
atmosphere. Developingvapour may
be inhaled or be
ignited by the sparks
the power tool produces.
3. Do not mix food. Power tools and their
accessories are not designed for processing food.
4. Ensure that the mixing container is placed in a
firm and secure position. A container that is not
properly secured may move
unexpectedly.
5. Follow the instructions and warnings for the
material to be mixed. Material to
be mixed may be
harmful.
6. Do not reach into the mixing container with
your hands or insert any other objects into it
while mixing. Contact with the
mixer blade may lead
to serious personal injury.
7. Start up and run down the tool in the mixing
container only. The mixer blade
may bend or spin
in an uncontrolled manner.
8. Ensure that no liquid splashes against the
housing of the power tool.Liquid that
has penetrated the power tool can
cause damage to the tool.
9. Use auxiliary handles, if supplied with the tool.
Loss of control may cause
personal injury.
10. Hold power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden
wiring. Cutting accessory contacting a
"live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
11. Always be sure you have a firm footing. Be
sure no one is below when using the tool in
high locations.
12. Hold the tool firmly.
13. Keep hands away from rotating parts.
14. Do not leave the tool running. Operate the tool
only when you are holding it.
15. Some materials contain chemicals which may
be toxic. Take caution to prevent dust
inhalation and skin contact. Follow safety
warnings by supplier of the material.
16. When performing the mixing operation, place
the mixing container on a flat and stable
surface.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical attention
right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a
container with other metal objects such
as nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
flow, overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.

9 ENGLISH
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation
requirements.
For commercial transports e.g.
by third parties, forwarding
agents, special requirement
on packaging and labeling must be
observed. For preparation of the item being
shipped, consulting an expert
for hazardous material is
required. Please also observe
possibly more detailed national
regulations.
Tape or mask off open contacts and pack up the
battery in such a
manner that it cannot
move around in the packaging.
11. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specified by Makita. Installing the batteries to
non-compliant products may result
in a fire, excessive
heat, explosion, or leak
of electrolyte.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result
in the battery
bursting causing fires,
personal injury and
damage. It will also
void the Makita
warranty for the Makita
tool and charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery
cartridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room
temperature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4. Charge the battery cartridge if you do not use
it for a long period (more than six months).
FUNCTIONAL
DESCRIPTION
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION: Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION: Hold the tool and the battery
cartridge firmly when installing or removing
battery cartridge. Failure to hold
the tool and the
battery cartridge firmly may
cause them to slip
off your hands and
result in damage to
the tool and battery
cartridge and a
personal injury.
CAUTION: Do not use this tool with the
battery adapter. If you connect
the battery adapter to
the tool, the battery
cover cannot be closed,
and using the tool
with battery cover opened
may cause an injury.
Open the battery cover while
pressing the button on the
battery cover.
►Fig.1: 1. Button 2. Battery cover
To remove the battery cartridge,
slide it from the tool
while sliding the button on the front of the cartridge. ►
Fig.2: 1. Red indicator 2. Button 3. Battery
cartridge
To install the battery cartridge,
align the tongue on the
battery cartridge with the groove
in the housing and slip
it into place. Insert it
all the way until it
locks in place with a
little click. If you can
see the red indicator on
the upper side of the
button, it is not locked
completely.
After installing the battery cartridge,
close the battery cover securely.

10 ENGLISH
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen. If not, it
may accidentally fall
out of the tool,
causing injury to you
or someone around you.
CAUTION: Do not install the battery cartridge
forcibly. If the cartridge does
not slide in easily,
it is not being
inserted correctly.
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
►Fig.3: 1. Indicator lamps 2. Check
button
Press the check button on
the battery cartridge to indicate
the remaining battery capacity. The
indicator lamps light up for a few seconds.
NOTE: Depending on the conditions of use and the
ambient temperature, the indication
may differ slightly from
the actual capacity.
Tool / battery protection system
The tool is equipped with
a tool/batteryprotection system. This
system automatically cuts off
power to the motor to
extend tool and battery life.
The tool will automatically
stop during operation if the
tool or battery is placed
under one of the following conditions:
Overload protection
When the tool or battery
is operated in a manner
that causes it to draw
an abnormallyhigh current, the
tool automatically stops without
any indication. In this situation,
turn the tool off and stop the application that caused the
tool to become overloaded. Then turn the tool on to
restart.
Overheat protection
When the tool or battery
is overheated, the tool
stops automatically. In this
case, let the tool and
battery cool before turning the tool on again.
Overdischarge protection
When the battery capacity is
not enough, the tool stops
automatically. In this case,
remove the battery from the
tool and charge the battery.
Switch action
CAUTION: Before installing the battery
cartridge into the tool, always check to see that
the switch trigger actuates properly and returns
to the "OFF" position when released.
CAUTION: Switch can be locked in "ON"
position for ease of operator comfort during
extended use. Apply caution when locking tool in
"ON" position and maintain firm grasp on tool.
CAUTION: Do not install the battery cartridge
with the lock button engaged.
CAUTION: When not operating the
tool, depress the trigger-lock button
from side to lock the switch trigger in theOFF
position.
►Fig.4: 1. Trigger-lock button
►Fig.5: 1. Switch trigger 2. Lock button 3.
Triggerlock button
To prevent the switch trigger
from accidentally pulled, the
trigger-lock button is provided. To start the tool, depress
the trigger-lock button from A ( ) side and pull the
switch trigger. Tool speed is
increased by increasing pressure on the
switch trigger. Release the switch trigger to stop. After
use, depress the trigger-lock button from B ( ) side.
For continuous operation, depress the lock buttonwhile
pulling the switch trigger, and then release the switch
trigger. To stop the tool,
pull the switch trigger fully,
then release it.
Indicator lamps
Remaining
capacity
Lighted
Off
Blinking
% to 100%
75
% to 75%
50
25
% to 50%
% to 25%
0
Charge the
battery.
The
ba
may
malfunctioned.

11 ENGLISH
Speed change
NOTICE: Use the speed change knob only after
the tool comes to a complete stop. Changing the
tool speed before the tool
stops may damage the
tool.
NOTICE: Always set the speed change knob
carefully into the correct position. If
you operate the tool with the
speed change knob positioned halfway between
the position 1 and
the position 2, the
tool may be
damaged.
NOTICE: If the rotation speed significantly
decreases during operation in the high speed
mode, stop the tool and change the mode to the
low speed mode. Otherwise, the motor
may get overloadedand
cause a malfunction
or fire.
Two speed ranges can be preselectedwith the speed
change knob.
To change the speed, turn the speed change knob so
that the pointer points to the position 1 for low speed or
the position 2 for high speed. ► Fig.6: 1. Pointer 2.
Speed change knob
Accidental restart preventive
function
If you install the battery
cartridge while pulling the switch
trigger or locking the switch trigger, the tool does not
start. To start the tool, release the switchtrigger, and
then pull the switch trigger.
The tool is equipped with
the electronic functions for easy
operation.
• Soft start
The soft-start function minimizes start-up shock,
and makes the tool start
smoothly.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing the front cover and side
grip
CAUTION: Tighten the side grip firmly.
Otherwise, the front cover may
fall and cause an
injury.
►Fig.7: 1. Front cover 2. Side grip
Attach the front cover to the tool and screw the side grip
on the tool securely.
The side grip canbe installed oneither side of the tool.
Installing the shaft
Optional accessory
For DUT130
1. Tighten the shaft into the shaft holder.
►Fig.8: 1. Shaft 2. Shaft holder
2. Tighten the shaft withwrench while holding the
shaft holder with another wrench. ► Fig.9:
1. Shaft 2. Shaft holder
For DUT131
1. Insert the shaft into the chuck as far as it will
go. ► Fig.10: 1. Shaft 2. Chuck
2. Tighten the chuck by
hand, and then place
the chuck key in
each of three holes
and tighten it clockwise.
Be sure to tighten
the chuck key at
all three holes evenly.
►Fig.11: 1. Chuck key
2. Chuck
To remove the shaft, turn
the chuck key counterclockwise
at one of the holes,
and then loosen the chuck
by hand.
Installing the mixing blade
Optional accessory
Attach the mixing blade on the top of the shaft, and then
secure it with the hex bolt.
►Fig.12: 1. Mixing blade 2. Shaft 3. Hex bolt
NOTICE: Be sure to attach the mixing blade with
"UP" mark facing the tool.
►Fig.13: 1. Mark
Optional accessory
Electronic function
Hook

12 ENGLISH
CAUTION: Always remove the battery when
hanging the tool with the hook.
CAUTION: Never hook the tool at high
location or on potentially unstable surface.
►Fig.14: 1. Groove 2. Hook 3. Screw
The hook is convenient for
temporarilyhanging the tool.
This can be installed oneither side of the tool. To
install the hook, insert it into a groove in the tool
housing on either side and then secure it with a screw.
To remove, loosen the screw and then take it out.
Installing or removing the shaft
holder
Optional accessory
For DUT131
1. Insert the hex wrenchinto the chuck, and
then loosen the chuck with the hex wrench while
holding the spindle with the wrench.
►Fig.15: 1. Hex wrench 2. Chuck 3. Wrench
2. Tighten the shaft holder with a wrench while
holding the spindle with another wrench.
►Fig.16: 1. Shaft holder 2. Wrench
To remove the shaft holder, perform the installation
procedure in reverse.
OPERATION
CAUTION: Do not mix flammable materials or
operate the tool around flammable materials such
as paint with thinner used as solvent. Failure to do
so may cause an injury.
CAUTION: Do not mix high viscosity material,
such as mortar or adhesive, in the high speed
mode. You may lose the
control of the tool
and cause an injury.
NOTICE: When you mix the material while the
mixing blade floating out of the material, be
careful not to splash the material.
1. Select high speed or low speed according to
the material to be mixed.
2. Hold the rear handle of the tool with one
hand and the grip with the
other hand firmly, place
the mixing blade under
material fully and turn
on the tool after
making sure work site
safety.
3. Move the mixing blade up and down during
the mixing operation so that whole part of material can
be mixed.
4. When finishing mixing, turn
off the tool, make
sure that the mixing blade has come
to a complete stop, and then pull it out of the mixing
container.
MAINTENANCE
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance
or adjustment should be performed
by Makita Authorized or Factory
Service Centers, always using Makita
replacement parts.
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita tool
specified in this manual. The use
of any other
accessories or attachments might present
a risk of injury to persons. Only
use accessory or
attachmentfor its stated purpose.
If you need any
assistance for more details regarding
these accessories, ask your
local Makita Service Center.
•Mixing blade
•Shaft
•Shaft holder
•Hook
•Makita genuine battery and
charger
NOTE: Some items in the
list may be included
in the tool package
as standard accessories.
They may differ from
country to country.
farklılık gösterebilir.

Makita Europe N.V. Jan-Baptist Vinkstraat 2,
3070 Kortenberg, Belgium
Makita Corporation 3-11-8, Sumiyoshi-cho,
Anjo, Aichi 446-8502 Japan
www.makita.com
885670A991
EN, FR, DE, IT, NL,
ES, PT, DA, EL, TR
20180911