Makita 6833 User manual

1
GB Auto Feed Screwdriver INSTRUCTION MANUAL
UA
      
PL
Wkrtarka z automatycznym podajnikiem INSTRUKCJA OBSUGI
RO
Main de înurubat cu alimentare automat MANUAL DE INSTRUCIUNI
DE Magazinschnellschrauber BEDIENUNGSANLEITUNG
HU Önetet csavarbehajtó HASZNÁLATI KÉZIKÖNYV
SK
Skrutkova s automatickým podávaním NÁVOD NA OBSLUHU
CZ Šroubovák se zásobníkem NÁVOD K OBSLUZE
6833
6834
6836

2
1
2
1 002629
1
2 002636
1
3 002648
1
2
4 002656
12
3
5 002657
12
3
4
6 002663
A
B
1
2
3
5mm
7 004177
1
2
3
8 002666

3
1
9 002667 10 002668
1
11 002669
1
12 002671
13 002676
12
15mm
14 004186
1
15 001145
1
2
16 002686

4
ENGLISH
Explanation of general view
1-1. Lock button
1-2. Switch trigger
2-1. Reversing switch
3-1. Hook
4-1. Casing
4-2. Thumb screw
5-1. Dust cover
5-2. Plane bearing
5-3. Bit
6-1. Lever
6-2. Stopper base
6-3. Plate
6-4. Casing
7-1. Stopper base
7-2. Casing
7-3. Adjusting knob
8-1. Feeder box
8-2. Screw strip
8-3. Screw guide
9-1. Driving position
11-1. Reverse button
12-1. Extension handle
14-1. Wall
14-2. Stopper base
15-1. Limit mark
16-1. Screwdriver
16-2. Brush holder cap
SPECIFICATIONS
Model 6833 6834 6836
Screw strip 4 mm
x 25 mm - 41 mm
4 mm
x 25 mm - 57 mm
4 mm
x 25 mm - 41 mm
No load speed (min-1) 4,700 2,800 6,000
Overall length 364 mm 396 mm 364 mm
Net weight 1.9 kg 1.9 kg 1.9 kg
Safety class /II
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
ENE033-1
Intended use
The tool is intended for screw driving in wood, metal and
plastic.
ENF002-1
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
For Model 6833
ENG003-2
For European countries only
Noise and Vibration
The typical A-weighted sound pressure level is 80 dB (A).
Uncertainty is 3 dB(A).
The noise level under working may exceed 85 dB (A).
Wear ear protection.
The typical weighted root mean square acceleration
value is not more than 2.5 m/s2.
These values have been obtained according to
EN60745.
For Model 6834
ENG003-2
For European countries only
Noise and Vibration
The typical A-weighted sound pressure level is 81 dB (A).
Uncertainty is 3 dB(A).
The noise level under working may exceed 85 dB (A).
Wear ear protection.
The typical weighted root mean square acceleration
value is not more than 2.5 m/s2.
These values have been obtained according to
EN60745.
For Model 6836
ENG003-2
For European countries only
Noise and Vibration
The typical A-weighted sound pressure level is 83 dB (A).
Uncertainty is 3 dB(A).
The noise level under working may exceed 85 dB (A).
Wear ear protection.
The typical weighted root mean square acceleration
value is not more than 2.5 m/s2.
These values have been obtained according to
EN60745.
ENH101-5
Model; 6833,6834,6836
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this
product is in compliance with the following standards of
standardized documents;
EN60745, EN55014, EN61000 in accordance with
Council Directives, 89/336/EEC, 98/37/EC.
Yasuhiko Kanzaki CE2005
000087

5
Director
MAKITA INTERNATIONAL EUROPE LTD.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
Responsible manufacturer:
Makita Corporation Anjo Aichi Japan
GEB017-1
SPECIFIC SAFETY RULES
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to screwdriver safety rules. If you use this power
tool unsafely or incorrectly, you can suffer serious
personal injury.
1. Hold power tools by insulated gripping
surfaces when performing an operation where
the cutting tool may contact hidden wiring or
its own cord. Contact with a "live" wire will make
exposed metal parts of the tool "live" and shock
the operator.
2. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not touch the bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
FUNCTIONAL DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on
the tool.
Switch action
Fig.1
CAUTION:
• Before plugging in the tool, always check to see
that the switch trigger actuates properly and
returns to the "OFF" position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
For continuous operation, pull the switch trigger and
then push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
Reversing switch action
Fig.2
CAUTION:
• Always check the direction of rotation before
operation.
• Use the reversing switch only after the tool comes
to a complete stop. Changing the direction of
rotation before the tool stops may damage the tool.
This tool has a reversing switch to change the direction
of rotation. Press the upper side (FWD side) of the
reversing switch for clockwise rotation or the lower side
(REV side) of the reversing switch for counterclockwise
rotation.
Hook
Fig.3
The hook is convenient for hooking the tool to your belt.
It can be installed on either side of the tool. To remove it,
pull it out in the direction of the arrow while raising. To
install the hook, push it down until it "clicks" into place on
the tool.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
Installing or removing the bit
Loosen the thumb screws which secure the casing. Pull
out the casing in the direction of the arrow.
Fig.4
Press the dust cover toward the plain bearing and pull
out the bit. If the dust cover cannot be moved as far as
the plain bearing, try it again after turning the bit slightly.
To install the bit, insert it into the socket while turning it
slightly. After installing, always make sure that the bit is
securely held in place by trying to pull it out.
Fig.5
Setting for desired screw length
Fig.6
There are 3 (for Model 6833 & 6836) or 5 (for Model
6834) positive-lock screw length settings. To obtain the
desired setting, pull out the stopper base while
depressing the lever until you see the number of the
desired screw length (indicated on the plate) appear to
rest on the very top edge of the casing. See the table
below for the relation between the number indicated on
the plate and the respective screw length ranges.

6
25/28 25 mm - 28 mm
32 28 mm - 35 mm
40 35 mm - 41 mm
* 51 41 mm - 51 mm
* 57 51 mm - 57 mm
Number indicated on the plate Screw length range
(Note) * for Model 6834 only
006404
Adjusting the driving depth
Fig.7
Depress the stopper base as far as it will go. While
keeping it in this position, turn the adjusting knob until
the bit tip projects approx. 5 mm from the stopper base.
Drive a trial screw. If the screw head projects above the
surface of the workpiece, turn the adjusting knob in the
"A" direction; if the screw head is counter-sunk, turn the
adjusting knob in the "B" direction.
Installing screw strip
Fig.8
Fig.9
Insert the screw strip through the screw guide. Then
insert it through the feeder box until the first screw
reaches the position next to the driving position.
Removing screw strip
Fig.10
Fig.11
To remove the sc rew strip, just pull it ou t in the direc tion
of the arrow. If you depress the reverse button, you can
pull out the screw strip in the reverse direction of the
arrow.
Extension handle (optional accessory)
Fig.12
Use of extension handle allows you to drive screws into
floors while standing.
OPERATION
Driving operation
Fig.13
Switch on the tool by pressing the switch trigger and at
the same time pushing the lock button. Hold the tool
squarely against the workpiece and apply forward
pressure to the tool. The screw will be automatically
carried to the driving position and driven into the
workpiece.
NOTE:
• Do not fire the tool without screws. This will
damage the workpiece.
• If the feeder box becomes sluggish in operation,
spray car wax (spray type wax) on its sliding
surfaces. Never lubricate it.
Driving in corner
Fig.14
This tool can be used to drive at a position 15 mm away
from the wall as shown in the figure.
CAUTION:
• Driving at a position closer than 15 mm to the wall
or driving with the stopper base in contact with the
wall may damage the screw heads and cause wear
on the bit. This may also lead to poor fastening of
screws and malfunction of the tool.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection
or maintenance.
Replacing carbon brushes
Fig.15
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps.
Take out the worn carb on brushes , insert t he new ones
and secure the brush holder caps.
Fig.16
To mainta in produc t SAFET Y and R ELIABI LI TY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers,
always using Makita replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Phillips bit
• Drywall screw strips
• Extension handle
• Plastic carrying case

7

   
1-1. 
1-2.  
2-1.   
3-1. 
4-1. 
4-2.    
5-1.  
5-2.  
5-3. 
6-1. 
6-2.  
6-3. 
6-4. 
7-1.  
7-2. 
7-3.  
8-1.  
8-2.   
8-3.  
9-1.  
11-1.   
12-1.  
14-1. 
14-2.  
15-1.  
16-1. 
16-2.  
 
 6833 6834 6836
   4 
x 25  - 41 
4 
x 25  - 57 
4 
x 25  - 41 
   (-1) 4700 2800 6000
  364  396  364 
  1,9  1,9  1,9 
  /II
•  ,        ,       
 .
• .        .
ENE033-1

     
,   .
ENF002-1
 
     
,   ,    
 ,   
    
 .   
     , ,
     
.
  6833
ENG003-2
   
  
      
80  (A).
 3 (A).
       85
 (A).
   .
   
  2,5 /2.
      
EN60745.
  6834
ENG003-2
   
  
      
81  (A).
 3 (A).
       85
 (A).
   .
   
  2,5 /2.
      
EN60745.
  6836
ENG003-2
   
  
      
83  (A).
 3 (A).
       85
 (A).
   .
   
  2,5 /2.
      
EN60745.

8
ENH101-5
; 6833,6834,6836
  
     ,
      
  ;
EN60745, EN55014, EN61000   
   89/336/EEC, 98/37/EC.
  CE2005
000087

   .
-, , -, 
 MK15 8JD, 
 :
    
GEB017-1
  

     
    (
   ), 
     
  .  
   
 ,   
.
1.   ,   
    
   , 
    
 .    
      
     
  .
2.    .
   
,     .
3.   .
4.    , 
.
5.      
 ,    
     .
  
:
   ,
     , 
   .
  
:
•     
,   ,  
    .
 .
Fig.1
:
•     
' ,   
    
   "".
  ,   
.   -   .
     ,
    .
     ,
       .
 -.
Fig.2
:
•      
 .
•    
    
.    
    
.
   
    .  
  ( "FWD") 
     
,    ( "REV")
     
 .

Fig.3
      
.     -
 .  ,   , 
    ,  .
      
,    .  
.

:
•  ,   
,   ,  
    .

9
   
  ,   . 
    ,  
.
Fig.4
     
 ,   . 
    
,     ,
  .
      
,   . 
  ,   
 ,   .
Fig.5
   

Fig.6
 3 (  6833  6836)  5 ( 
6834)    
.    
   ,  
,       '
   (  ).
      
    - .
  .
25/28 25 мм - 28 мм
32 28 мм - 35 мм
40 35 мм - 41 мм
* 51 41 мм - 51 мм
* 57 51 мм - 57 мм
Номер вказаний на табличці Діапазон довжини гвинта
(Примітка) * тільки для моделі 6834
006404
  
Fig.7
     . 
   ,  
    
  5    . 
 .     
 ,    
  "",    , 
     "".
   
Fig.8
Fig.9
     . 
    ,  
      
.
   
Fig.10
Fig.11
       
   .   
  ,    
    .
  (
)
Fig.12
    
    .

 
Fig.13
 ,   ,
    .
       
    . 
    
     .
:
•     . 
 .
•       
,    
()   .
  .
  .
Fig.14
    
     15   ,
   .
:
•   ,   15 
 ,  ,  
  ,   
    
.     
     
.

10
 
:
•  ,   , 
 , ,  
    .
  
Fig.15
     .
 ,     .
      
  .  
   . 
   .
    
.    , 
    .
Fig.16
 ,    
, ,   
    
 "",   
  "".

:
•     
    "", 
    .
    
   .
    
  .
  ,    
    
    "".
•  Phillips
•    
•  
•    