Manhattan Comfort Rockefeller User manual

888-230-2225
[email protected]
Rockefeller
dresser

Included in the package
10
02
12
11
Tools needed
(not included)
Phillips screw driver
Screw driver
01 - Base = 01 piece
02 - Left side panel = 01 piece
03 - Right side panel = 01 piece
04 - Top panel = 01 piece
05 - Lower back panel = 01 piece
06 - Front of the drawer = 03 pieces
07 - Left side panel of the drawer = 03 pieces
08 - Right side panel of the drawer = 03 pieces
09 - Rear panel of the drawer = 03 pieces
10 - Base of the drawer = 03 pieces
11 - Decorative apply = 03 pieces
12 - Feet = 04 pieces
13 - Upper back panel (hole) = 01 piece
14 - Plastic union profile = 01 piece
Rockefeller
dresser
01
06
09
08
05
14
A = 16x B = 16x C = 08x
L = 16x
E = 16x G = 28xD = 16x
K = 01xH = 01x J = 01x
13
02/08
F = 23x
I = 12x
07
03
04

Fix the parts (12) under
the part (01) with
the hardware (A).
Step 01
01
12
Front View Rear View
03/08
A
A A
A
A
A A
A
A
A A
A
A
A A
A
Rockefeller
dresser
11 lb
11 lb
11 lb
11 lb

Connect the part (04) onto the parts (02)
and (03) using the hardware (C )
and the hardware (D + E)
Apply the hardware (L) on
the hardware (E).
Connect the parts (02) and (03) onto
the part (01) with the hardware (C )
and the hardware (B).
B
Step 03
Step 02
01
02
03
B
B
C
C
C
C
E
E
C
D
04
02
03
L
L
L
04/08
D
C
C
E
D
Rockefeller
dresser

06
11
Connect the part (11) onto the
part (06) with the hardware (F).
F
F
F
Connect the part (05) and the part (13)
joining with the part (14)
and the hardware (G).
Step 05
Step 04
G
13
05
05 13
14
05/08 Rockefeller
dresser

Step 03
Step 07
Step 06
06/08
08
07
09
B
B
B
B
10
06
08
07
D
D
E
D
D
E
E
L
EL
L
L
Connect the parts (07), (08) and (09)
with the hardware (B).
Apply the part (10)
in the groove of the
parts (07) and (08)
until the groove
of the part (09).
Connect parts (07), (08) and (06)
using the hardware (D + E).
Apply hardware (L)
on the hardware (E).
Rockefeller
dresser

Step 03
Step 09
Step 08
07/08
Use the hardware (I) with the
hardware (F) as shown
on detail.
Install the drawer fitting it into
the slides fixed on the side
of parts (02) and (03).
F
FF
F
I
II
I
09
06
02
03
Rockefeller
dresser

Step 10
H = 01x K = 01x
wall
First, approach as close
as possible to the wall
Then, pass the hardware (K)
through the hole of the
part (13) as shown in the figure above.
You will need a pencil to mark where you
should drill the wall with a 3/8" drill bit
to put in the hardware (J).
J = 01x
13
K
*press the hardware wings (J) to put in the hole that
you drilled in the wall.
J
wings
wings
Hardware (J), plugged in the wall.
J
K
F
Then fasten with the hardware (F) the
hardware (K) on the part (04)
H
F
04
Attention! Tipover System
08/08
F = 02x
Rockefeller
dresser