Manitou Mara Pro User manual

MARA 50 HOUR AIR CAN & PISTON | SERVICE GUIDE

5800 W Donges Bay Rd
Mequon, WI 53092
manitoumtb.com
888.686.3472
Support: manitoumtb.com/support
MANITOU
Warranty:
For full warranty information please visit hayesbicycle.com/warranty
Revised September 16, 2020 11:49 AM

3
50 HOUR AIR CAN & PISTON GUIDE
Suspension shocks by design can contain preloaded springs, gases and uids under
extreme pressures. Warnings contained in this manual must be observed to avoid damage to shock,
serious injury or even death.
We highly recommend that service to this shock be performed by a cered bicycle
mechanic. Failure to follow instrucons presented in this manual could lead to serious injury or
death. Any quesons about the servicing of this shock or the manual itself should be directed to
Manitou Customer Support at:
Phone: [phone]
Email: [e-mail]
This manual is intended to guide the user through the steps necessary to service the air can and air
piston of the Mara Pro and Mara Inline rear shock.
INTRODUCTION

450 HOUR AIR CAN & PISTON GUIDE
TABLEOFCONTENTS
SECTION PAGENUMBER
REQUIRED TOOLS 5
AIR CAN REMOVAL 6–7
KING CAN SERVICE 8-9
AIR CAN SERVICE 10–13
AIR PISTON SERVICE 14–15
AIR CAN INSTALL 16–17

5
50 HOUR AIR CAN & PISTON GUIDE
Below is a list of tools necessary for servicing the Mara shock.
• Safety Glasses
• Nitrile Gloves
• Lint-Free Rags
• Isopropyl Alcohol
• Slickoleum grease
- 10-oz Tub - Manitou Part Number 20-32929
- 5Ml Tube - Manitou Part Number 141-33604-K001
• Air Can Wrench - Manitou part number 142-37512-K033
• Air Can Seal Install Tool - Manitou part number 172-32193-K001 (Optional)
• Plastic O-ring pick
• Torque wrench
• Bench mounted Vise
• Hand Dyno
• Shock Pump
• Air Can Seal Kit - Manitou Part Number 142-31535-K002
• King Can Seal Kit - Manitou Part Number 142-31535-K035
REQUIREDTOOLS

650 HOUR AIR CAN & PISTON GUIDE
Remove valve cap, thread
shock pump on. Note air
pressure and use pump’s re-
lease valve to release all air
from shock. (Use a 3mm
hex key to gently depress the
valve, ensuring all air is re-
leased.)
1
2
AIRCAN REMOVAL
Clamp upper eyelet of shock in
vise. If Trunnion shock, clamp
on trunnion mounts. (Use soft
jaws to not damage the shock)
With the shock top cap in a
vise use the air can wrench PN
142-37512-K033 to loosen the
air can on the shock. DO NOT
completely remove the air can
at this point, only loosen one
full turn. Removing the air
can completely at this point
will damage the threads due
to pressure in the negative
chamber.
3
Do not proceed to next
step without completely
depressurizing the air spring.
CAUTION

7
50 HOUR AIR CAN & PISTON GUIDE
AIRCAN REMOVAL
4
5
Place shock in a hand dyno or
in a bicycle frame, compress
the shock. At this point
unthread the air can fully.
Remove air can, bumper, and
spacers (if present). These
may remain in the air can,
locate and save for later re-
assembly.

850 HOUR AIR CAN & PISTON GUIDE
KINGCANSERVICE
Remove wire ring and slide
outer air can sleeve o of the
inner can.
Remove the upper and lower
O-rings. (Remove Mid King
O-ring if being used.)
Lightly Grease new O-rings
and install into seal glands
using a plastic O-ring tool or
by hand.
1
2
3

9
50 HOUR AIR CAN & PISTON GUIDE
kingCAN service
Slide outer air can sleeve onto
inner can. Install wire ring.
4

10 50 HOUR AIR CAN & PISTON GUIDE
AIRCAN service
1
2
3
Remove the negative chamber
MCU and spacer(s). Carefully
remove the dust wiper using
an O-ring pick.
Remove glide ring from the air
can.
Remove quad ring from the air
can.

11
50 HOUR AIR CAN & PISTON GUIDE
AIRCAN service
4
5
6
To make air can seal
installation easier use the Air
Can Seal Install tool, Manitou
part number 172-32193-K001.
Place the air can onto the seal
tool or onto a at surface.
This cut away of the air can
shows the seal placement
for reference. The air can
quad seal is the bottom seal
followed by the white glide
ring. They both sit in the lower
groove. The air can wiper seal
sits in the upper groove.

12 50 HOUR AIR CAN & PISTON GUIDE
AIRCAN service
7
8
9
Install the air can quad ring
into the lower groove in the air
can. Ensure it is not twisted.
Install the air can glide ring
into the same groove as the
quad ring. It will sit on top of
the quad ring.
Remove the new air can quad
ring from the seal kit and
liberally apply Slickoluem
grease.

13
50 HOUR AIR CAN & PISTON GUIDE
AIRCAN service
10 Lightly grease and install the
air can wiper seal into the
upper groove of the air can.

14 50 HOUR AIR CAN & PISTON GUIDE
AIRpistonservice
1
2
3
Remove the split glide ring
from the air piston.
Remove the air piston quad
seal. DO NOT REMOVE WHITE
GLIDE RING! Clean the white
glide ring and air piston with
isopropyl alchohol.
Liberally grease the air piston
quad ring.

15
50 HOUR AIR CAN & PISTON GUIDE
AIRpistonservice
8
9
10
Install the air piston quad ring
onto the air piston.
Ensure the air piston quad ring
is not twisted and push it tight
against the glide ring, making
a space for the split glide ring.
Install the split glide ring onto
the air piston.

16 50 HOUR AIR CAN & PISTON GUIDE
Install foam ring and spacer(s)
onto damper body.
Install air can onto shock as
far as it can be easily pushed.
Due to the negative chamber it
can be dicult to install air can
completely without mounting it
in a frame or shock tester and
compressing the shock.
Apply Slickoleum grease to the
air piston seals.
AIRCAN INSTALL
1
2
3

17
50 HOUR AIR CAN & PISTON GUIDE
Install shock into bench
tester or frame and partially
compress shock. Compress
until air can can be threaded
onto top cap.
Tighten air can onto shock
until the hard stop. Do not
tighten past this point.
Set the air pressure, clean
shock, update the tuning
notes and go ride!)
AIRCAN INSTALL
4
5
6

16F, No. 37, Sec. 3
Mincyuan E. Rd.
Zhongshan District
5800 W. Donges Bay Rd.
Mequon, WI 53092
Dirnismaning 20 a
85748 Garching (b. Munich)
Germany
16F, No. 37, Sec. 3
Mincyuan E. Rd.
Zhongshan District
GLOBAL HEADQUARTERS &
HAYES BICYCLE GROUP USA
HAYES BICYCLE GROUP EU
HAYES BICYCLE GROUP ASIA
facebook.com/ManitouMTB
instagram.com/ManitouMTB
#ScienceofSmooth