Manitou MT 732 EASY 75D ST3B S1 User manual

MT 732 EASY 75D ST3B S1
MT 932 EASY 75D ST3B S1
THIS MACHINE IS AN ALL TERRAIN FORKLIFT TRUCK DESIGNED TO OPERATE ON NATURAL OR UNDEVELOPED LAND, OR CONSTRUCTION SITES.
t
IMPORTANT
t
This document is a short recap on how to drive a forklift truck, and should in no way be a substitute for the manual required by Directive 2006/42/CE Annex I § 1.7.4, which should be read and
understood by the operator beforehand and is available in the forklift truck’s cab.
All instructions, including safety instructions, which are in the manual but are not included in this document should be implemented and enforced.
The operator must have received proper training and must comply with the rules in force on road traffic.
TECHNICAL CHARACTERISTICS
WEIGHT OF FORKLIFT TRUCK WITH STANDARD ATTACHMENT
(Transport position)
MT 732 MT 932
- No load 6780 kg 7145 kg
- Maximum load 9980 kg 10345 kg
- Front axle load 3280 kg 3445 kg
- Rear axle load 3500 kg 3700 kg
- Front axle maximum load 8680 kg 8745 kg
- Rear axle maximum load 1300 kg 1600 kg
DRAWBAR PULL ON THE COUPLING HOOK
- No load (slipping) 5300 daN 5530 daN
- Maximum load (timing transmission) 8000 daN 7320 daN
DIMENSIONS
MT 732 MT 932
- A 1200 mm 1200 mm
- B 2810 mm 2810 mm
- C 1193 mm 1128 mm
- D 4761 mm 4696 mm
- F 1930 mm 1930 mm
- I 758 mm 758 mm
- U1 2299 mm 2299 mm
- U2 2488 mm 2488 mm
B
D
C
A
U1
U2
IF
CONTROL AND SIGNAL LIGHTS PANEL
CONTROL PANEL
A - ENGINE WATER TEMPERATURE
B - REV COUNTER
C - FUEL LEVEL
D - ENGINE PREHEAT INDICATOR LAMP
E - ENGINE PREHEATING FAULT INDICATOR LIGHT
F- CUT-OFF ENGINE INDICATOR LAMP
G - STEERING SYSTEM OIL PRESSURE WARNING INDICATOR LAMP
H - GEAR BOX OIL PRESSURE WARNING INDICATOR LAMP
I - GEAR BOX OIL TEMPERATURE WARNING INDICATOR LAMP
J - BRAKING OIL LEVEL WARNING INDICATOR LAMP
K - PARKING BRAKE INDICATOR LAMP
L - BATTERY CHARGE WARNING INDICATOR LAMP
M - ENGINE OIL PRESSURE INDICATOR LAMP
N - ENGINE WATER LEVEL WARNING INDICATOR LAMP
O - AIR FILTER OR HYDRAULIC RETURN FILTER CLOGGING WARNING INDICATOR LAMP
P - INDICATOR LIGHTS INDICATOR LAMP
Q - SIDELIGHTS INDICATOR LAMP
R - LOW BEAM INDICATOR LAMP
S - MAIN BEAM INDICATOR LAMP
SCREEN DISPLAY
• Drive direction indicator.
• The hour meter.
• The clock.
- Short press button 1 to move successively from one screen to another, hold down
the button to enter the menus.
B
M N OG I K
SRQ
C
P
A
D FE H J L
1
SWITCHES
The location of the switches may vary depending on the options.
A - OPTION Electrical boom pre-equipment
OPTION Head telescope electrovalve
B - OPTION Blue working headlight
C - Wheel alignment indicator lamps
D - Hazard warning lights
E - Rear fog light
F - Self-cleaning fan option
G - Steering selection
H - Transmission cut-off
N - OPTION Engine speed regulator
O - Rotating beacon light
P - OPTION Front and rear working headlights
Q - OPTION Hydraulic locking attachment
R - Neutralization of hydraulic movements
S - OPTION Easy hydraulic attachment connection
T - OPTION Telescope suspension
A DCB
E HGF
N RQPO
S T
This device warns the operator of the longitudinal stability
limits of the forklift. Depending on the type of work
required, the longitudinal stability limiter and warning
device allows the operator to operate the lift truck in
complete safety.
The A8 LED indicates that the forklift truck is at the
authorized limit for longitudinal stability. If the light comes
on, perform smooth hydraulic movements.
HANDLING Use with forks.
“GODET” MODE Use with tipping dumpster.
ACTIVATION: Hold the button for 2 seconds, the
“GODET” MODE is confirmed with a beep and
the indicator light.
OFF: Press the button again.
“SUSPENDED LOADS” MODE For more security, use with a bracket
ACTIVATION: Hold the button for 2 seconds, the “SUSPENDED LOADS”
MODE is confirmed with a beep and the indicator light.
OFF: Press the button again.
A permanently lit fault indicator light, together with a combination
of illuminated LEDs, indicates a major fault liable to affect the safety of the
forklift truck. Refer to the manual.
A8
LONGITUDINAL STABILITY LIMITER AND WARNING DEVICE
BASIC INSTRUCTION SHEET No. 52517602EN (2014/10/10)

t
IMPORTANT
t
Operators' attention is drawn to the risks involved in using the forklift truck, in particular:
- Risk of losing control.
- Risk of losing lateral and frontal stability of the forklift truck.
The operator must remain in control of the lift truck. In the event of the lift truck overturning, do not try to leave the cabin during the incident.
YOUR BEST PROTECTION IS TO STAY FASTENED IN THE CABIN.
FUSES AND RELAYS IN THE CAB
K5 K6
K9K8
K7
K4K3K2
K1K0
F30F26 F27 F28 F29F16 F17 F18 F19 F20 F21 F22 F23 F24 F25
15A max10A15A max15A15A max7.5A max 7.5A7.5A 15A7.5A 15A 15A15A 25A7.5A
OPT.OPT.
DIAG OPT.OPT.
F15F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14
20A25A max20A10A max 7.5A10A15A 7.5A 7.5A max 15A max 5A 10A 15A max15A 10A
OPT. ECU
HYD.
OPT.
OPT.ECM
N°52505437
K17K18
STOP
OPT.
OPT.
LSU
OPT. OPT.
F33 F32 F31
2A 5A 5A
DIAG
SPU
TEST
N
K23
K21
30A
5A
F44
F41F42F43
80AF49
F48
F47
60A
30A
F46 F45
10A
pump
Fuel
N°52505436
Diagn
pump
Fuel
ECM
FUSES AND RELAYS UNDER THE ENGINE BONNET
DAILY MAINTENANCE
CHECK THE ENGINE OIL LEVEL CHECK THE COOLING
LIQUIDLEVEL CHECK THE FUEL LEVEL CHECK THE FUEL PRE-FILTER
CHECK LONGITUDINAL
STABILITY LIMITER AND
WARNING DEVICE
INSTRUCTION SHEETS AND OPTIMAL LOAD CHARTS
tIMPORTANT t
See the instruction sheets for use of
the forklift truck.
Comply with the optimal load
charts.
MANUAL ATTACHMENT LOCKING
tIMPORTANT t
Before any use, ensure that the
attachment is properly locked.
HYDRAULIC CONTROLS
A - Lifting and tilting control
lever.
B - Telescoping control button.
C - Attachment control button.
D - Head telescope electrovalve
OPTION control button.
E - Forward/neutral/reverse gear
selection
D
E
B
C
A
STOWING THE LIFT TRUCK
tIMPORTANT t
Ensure that the safety instructions associated
with the platform are complied with before
loading the lift truck and that the driver of the
carrier vehicle is informed of the dimensions and
the weight of the forklift truck.
STOWING THE LIFT TRUCK
- Fix the chocks to the platform at the front
and at the back of each tire.
- Also fix the chocks to the platform
ontheinside of each tire.
- Secure the lift truck to the platform with
sufficiently strong ropes to the anchoring
points provided.
Authorization to move the lift truck is controlled by an electronic unit. The operator must observe the following sequence
to move the truck forwards or backwards:
• 1 - sit down correctly in the driver’s seat,
• 2 - release the parking brake,
• 3 - engage forward or reverse movement.
NOTE: The alternating display of F/N or R/N on the screen and a rapid, discontinuous beep indicates that the selector needs
to be set to neutral.
To stop the lift truck, he must observe the following sequence:
• 1 - set the forward/reverse selector to neutral,
• 2 - engage the parking brake,
• 3 - get out of the lift truck.
NOTE: A discontinuous beep will inform the driver if he has left the driver's cab without applying the parking brake.
SAFETY FOR MOVING THE FORKLIFT TRUCK STEERING SELECTOR
tIMPORTANT t
Never change the steering mode whilst driving.
B1 - Front drive wheels (highway traffic).
B2 - Front and rear drive wheels in opposite direction
(short steering lock).
B3 - Front and rear drive wheels in the same
direction (crab steering).
B3
B1
B2