Maretron TSM800C User manual

Revision 1.0 Page i
TSM800C
8” Vessel Monitoring and Control
Touchscreen
User’s Manual
Revision 1.0
Copyright © 2014 Maretron, LLP All Rights Reserved
Maretron, LLP
9014 N. 23rd Ave #10
Phoenix, AZ 85021-7850
http://www.maretron.com
Maretron Manual Part #: M003053

TSM800C User's Manual
Page ii Revision 1.0
Revision History
Rev.
Description
1.0
Original document

Revision 1.0 Page iii
Table of Contents
1General..........................................................................................................................................1
1.1 Introduction ........................................................................................................................1
1.2 Firmware Revision .............................................................................................................2
1.3 TSM800C Features............................................................................................................2
1.4 Quick Install........................................................................................................................2
2Installation......................................................................................................................................4
2.1 Unpacking the Box.............................................................................................................4
2.2 Choosing a Mounting Location...........................................................................................4
2.3 Mounting the TSM800C .....................................................................................................5
2.3.1 Mounting Considerations..............................................................................................5
2.3.2 Ergonomics...................................................................................................................6
2.3.3 Arm Mounting ...............................................................................................................8
2.4 Connecting the TSM800C..................................................................................................9
2.4.1 LAN Connection..........................................................................................................10
2.4.2 USB Device Connection .............................................................................................11
2.4.3 Power Connection.......................................................................................................12
2.4.4 Grounding Screw........................................................................................................13
2.4.5 NMEA 2000®Connection............................................................................................13
2.5 Power Sequencing...........................................................................................................14
2.6 Configuring the TSM800C................................................................................................14
2.6.1 Manually Entering LAN Connection Information .........................................................15
3Operating the TSM800C..............................................................................................................18
3.1 Turning the TSM800C On................................................................................................18
3.2Turning the TSM800C Off................................................................................................18
3.3 Adjusting the Screen Brightness on the TSM800C ..........................................................18
3.4 Using the TSM800C.........................................................................................................18
4Maintenance................................................................................................................................19
5Troubleshooting...........................................................................................................................20
6Mechanical Drawings...................................................................................................................21
7Technical Specifications ..............................................................................................................22
8Technical Support........................................................................................................................24
9Maretron (1 Year) Limited Warranty.............................................................................................25

TSM800C User's Manual
Page iv Revision 1.0
Table of Figures
Figure 1 –TSM800C Network Diagram................................................................................................1
Figure 2 –TSM800C Cutout Dimensions (units in mm [inches])...........................................................7
Figure 3 –TSM800C VESA Arm Mounting Retention Screw Holes......................................................8
Figure 4 –TSM800C Bottom Panel......................................................................................................9
Figure 5 –TSM800C Rear Panel........................................................................................................10
Figure 6 –LAN Connection.................................................................................................................11
Figure 7 –USB Device Connection ....................................................................................................12
Figure 8 –Power Connections............................................................................................................12
Figure 9 –Attaching Power Cables to Connector...............................................................................13
Figure 10 –NMEA 2000®Connector Face Views...............................................................................14
Figure 11 –TSM800C Startup Screen................................................................................................15
Figure 12 –N2KView®Window with Tabs Displayed..........................................................................16
Figure 13 –Configuration Dialog, Network Tab.................................................................................17

Revision 1.0 Page 1
1 General
1.1 Introduction
Congratulations on your purchase of the Maretron TSM800C Vessel Monitoring and Control
Touchscreen. Maretron has designed and built your display to the highest standards for years of
dependable and accurate service.
The TSM800C is an 8” dedicated touchscreen that includes Maretron’s N2KView®vessel monitoring
and control software. The N2KView®software allows you to configure as many favorite screens as
you want with exactly the information you want to see. The TSM800C provides an extremely simple
touch interface for monitoring and controlling critical systems from anywhere on the vessel.
The TSM800C is ruggedized for marine use and includes a solid state disk drive to withstand the
pounding associated with waves. And since the TSM800C only dissipates 20 watts, there is no need
for internal cooling fans that are noisy and wear out causing electronics to overheat and fail. The
TSM800C can be mounted outside given the high bright screen and waterproof front.
As an alternative to controlling the TSM800C through the touch screen, the TSM800C includes two
USB ports for connecting keyboards, mice, or trackballs. The TSM800C also has an Ethernet port for
connecting Internet Protocol (IP) cameras for viewing within the N2KView®software. Lastly, the
TSM800C contains two completely isolated CAN bus connectors (M12) for easy connection to single
or redundant NMEA 2000®networks.
The Maretron TSM800C is designed to operate within the harsh demands of the marine environment.
However, no piece of marine electronic equipment can function properly unless installed, configured,
Figure 1 –TSM800C Network Diagram
Optional
USB Keyboard
Or Mouse
Engine
Monitor
Battery
Monitor
Electrical
Panel
Tank
Monitor
NMEA 2000
Network
TSM800
C

TSM800C User's Manual
Page 2 Revision 1.0
and maintained in the correct manner. Please read carefully and follow these instructions for
installation, configuration, and usage of the Maretron TSM800C in order to ensure optimal
performance.
1.2 Firmware Revision
This manual corresponds to the TSM800C running N2KView®Version 4.0.2.
1.3 TSM800C Features
NOTE
Although the TSM800C looks similar to the former TSM800 product, there are
important differences. The TSM800C is a standalone NMEA 2000®display, with the
following features:
The TSM800C includes two CAN interfaces for direct connection to one or
two NMEA 2000®networks.
The TSM800C includes all N2KView®capabilities that were formerly
licensed separately in the TSM800: Alerts, Control, Fuel Management, and
Video. No gateways (such as the IPG100), hardware license keys, or
additional software licenses are needed.
You don’t need to connect or configure LAN connections, unless you are
using Video or E-mail alert actions.
N2KView®configurations are transferred to and from other N2KView®
devices using a USB flash drive plugged into one of the TSM800C’s USB
ports.
The Maretron TSM800C has the following features:
8” TFT LCD Panel, LED Backlit
Widescreen Aspect Ratio 5:3
800 x 480 Pixels
600 nits Brightness (Optically Bonded)
Solid State Disk Drive
Fanless Cooling System
Flush mounting hardware included
Optional VESA mounting capability
All N2KView licenses included
2 isolated NMEA 2000®connectors for direct connection to single or dual NMEA 2000®
networks
1.4 Quick Install
Installing the Maretron TSM800C display involves the following five steps. Please refer to the
individual sections for additional details.

Revision 1.0 Page 3
Unpacking the Box (Section 2.1)
Choosing a Mounting Location (Section 2.2)
Mounting the TSM800C (Section 2.3)
Connecting the TSM800C (Section 2.4)
Configuring the TSM800C (Section 2.6)

TSM800C User's Manual
Page 4 Revision 1.0
2 Installation
2.1 Unpacking the Box
When unpacking the box containing the Maretron TSM800C, you should find the following items:
1 –TSM800C 8” Vessel Monitoring and Control Touchscreen
1 –TSM800C User’s Manual
1 –N2KView®Documentation CD-ROM
1 –1m USB Cable with Waterproof Bulkhead Connector
1 –Warranty Registration Card
If any of these items are missing or damaged, please contact Maretron.
2.2 Choosing a Mounting Location
The TSM800C front panel is splash proof (IEC IP66 rating –protected against the effects of powerful
water jets), while the rear of the TSM800C is drip proof (IEC IP22 rating –protected against the
NOTE
To prevent damage to chassis corners and/or breaking front glass, please review the
illustrations below before handling the TSM800C.

Revision 1.0 Page 5
effects of dripping water when tilted up to 15°). The TSM800C may be mounted either in an indoor or
outdoor location.
Adequate ventilation is a necessary prerequisite for the life of the product. The air inlet and outlet
openings must definitely be kept clear; coverings which restrict ventilation are not permissible.
Generally, do not install the unit in a horizontal position (laying down), as this will cause heat to build
up inside the unit which will damage the LCD Panel. To prevent this problem, we recommend
installing the unit in a vertical position (±30 degrees) to improve the airflow through the unit.
To further improve the cooling of the unit, we recommend installing Cooling Fans underneath blowing
upwards into the unit air inlet. This may be required in high temperature applications and also when
there is reason to expect temperature problems due to non-optimal way of mounting.
Exposure to extreme direct sunlight can cause a considerable increase in the temperature of the unit,
and might under certain circumstances lead to overtemperature. This point should already be taken
into consideration when the bridge equipment is being planned (sun shades, distance from the
windows, ventilation, etc.).
Space necessary for ventilation, for cable inlets, for the operating procedures and for maintenance,
must be provided.
Proper strain relieve should be installed on cables attached to the TSM800C so that cable breaks will
not occur, e.g. during service work.
Do not paint the product. The surface treatment influences on the excess heat transfer. Painting,
labels or other surface treatments that differ from the factory default, might cause overheating.
Expose to heavy vibration and acoustic noise might under certain circumstances affect functionality
and expected lifetime. This must be considered during system assembly and installation. Mounting
position must carefully be selected to avoid any exposure of amplified vibration.
2.3 Mounting the TSM800C
The TSM800C has two mounting options, which include:
Wall/Panel mounting
Arm mounting (requires purchase of a VESA 75mm mounting arm)
2.3.1 Mounting Considerations
The useful life of the components of all Electronics Units generally decreases with increasing ambient
temperature; it is therefore advisable to install such units in air-conditioned rooms. If there are no
such facilities, these rooms must at least be dry, adequately ventilated and kept at a suitable
temperature in order to prevent the formation of condensation inside the display unit.
Since the TSM800C is fanless, cooling takes place via the surface of the casing. The cooling must
not be impaired by partial covering of the unit or by installation of the unit in a confined cabinet.

TSM800C User's Manual
Page 6 Revision 1.0
In the area of the wheel house, the distance of each electronics unit from the magnetic standard
compass or the magnetic steering compass must not be less than the permitted magnetic protection
distance. This distance is measured from the centre of the magnetic system of the compass to the
nearest point on the corresponding unit concerned.
Units which are to be used on the bridge wing must be installed inside the “wing control console”
protected against the weather. In order to avoid misting of the viewing screen, a 25 ... 50 W console-
heating (power depending on the volume) is recommended.
When selecting the site of a display unit, the maximum cable lengths have to be considered.
When a product is being installed, the surface base or bulkhead must be checked to ensure that it is
flat in order to avoid twisting of the unit when the fixing screws are tightened, because such twisting
would impair mechanical functions. Any unevenness should be compensated for by means of
spacing-washers.
The grounding screws of the units must be connected to the body of the ship (ground); the wire used
should have a cross sectional area of at least 6 mm2.
Transportation damage, even if apparently insignificant at first glance, must immediately be examined
and be reported to the freight carrier. The moment of setting-to-work of the equipment is too late, not
only for reporting the damage but also for the supply of replacements.
The classification is only valid for approved mounting brackets provided by Maretron. The unit shall
be mounted stand-alone without any devices or loose parts placed at or nearby the unit. Any other
type of mounting might require test and re-classification.
2.3.2 Ergonomics
Adjust the unit height so that the top of the screen is at or below eye level. Your eyes should look
slightly downwards when viewing the middle of the screen.
Adjust screen inclination to remain gaze angle to the centre of the screen approximately
perpendicular to the line of gaze.
When products are to be operated both from a sitting position and from a standing position, a screen
inclination of about 30° to 40° (from a vertical plane) has turned out to be favorable.
The brightness of displays is limited. Sunlight passing directly through the bridge windows - or its
reflection –which falls upon the screen workplaces must be reduced by suitable means (negatively
inclined window surfaces, venetian blinds, distance from the windows, dark coloring of the deckhead).
These units are equipped with optical enhanced technology to reduce reflections and are viewable in
direct sun light, but as a general rule the units at the bridge wing area is recommended to be installed
or mounted by suitable alignment or bulkhead /deckhead mounting in such a way that reflections of
light from the front panel of the display are not directed into the observer’s viewing direction.
The use of ordinary commercial filter plates or filter films is not permitted for items of equipment that
require approval (by optical effects, “aids” of that kind can suppress small indicators, for example).

Revision 1.0 Page 7
Figure 2 –TSM800C Cutout Dimensions (units in mm [inches])
Step 1: Select the position on the panel or wall to mount the TSM800C.
Step 2: Cut out a section from the panel that corresponds to the rear panel dimensions of the
TSM800C. Take care that the panel section that is cut out is smaller than the overall size of
the front panel of the TSM800C but just large enough for the rear panel of the TSM800C to fit
through, according to the dimensions in Figure 2 above.
Step 3: Drill four 6mm holes for the M5 studs protruding from the four corners of the front panel
according to the dimensions in Figure 2 above.
Step 4: Slide the TSM800C through the hole until the frame is flush against the panel.
Step 5: From behind the panel, screw the four supplied mounting nuts onto the M5 studs protruding
from the rear of the frame, and tighten until the display is firmly secured to the panel.

TSM800C User's Manual
Page 8 Revision 1.0
2.3.3 Arm Mounting
The TSM800C is VESA (Video Electronics Standards Association) compliant and can be mounted on
an arm with a 75mm interface pad. To mount the TSM800C on an arm, please follow the steps below.
Step 1: Please correctly mount the arm onto the base surface. To do this, refer to the installation
documentation that came with the mounting arm.
Step 2: Once the mounting arm has been firmly attached to the base surface, lift the TSM800C onto
the interface pad of the mounting arm.
Step 3: Align the retention screw holes on the mounting arm interface with those in the TSM800C.
The arm mount retention screw holes are shown in Figure 3.
Step 4: Secure the TSM800C to the interface pad by inserting the retention screws through the
bottom of the mounting arm interface pad and into the TSM800C.
Figure 3 –TSM800C VESA Arm Mounting Retention Screw Holes
NOTE
When purchasing a mounting arm please ensure that it is VESA compliant and that
the arm has a 75 mm interface pad. If it is not VESA compliant, it cannot be used to
support the TSM800C.

Revision 1.0 Page 9
2.4 Connecting the TSM800C
Most I/O interface connections of the TSM800C are found on the bottom panel. The I/O interface
panel located on the bottom of the TSM800C has the following I/O interface connectors:
2 x 24V DC Power input connector
1 x RJ-45 Gigabit Ethernet LAN port
2 x USB 2.0 connectors
1 x Grounding Screw
The bottom panel of the TSM800C is shown in Figure 4.
Figure 4 –TSM800C Bottom Panel
Additionally, the rear panel of the TSM800C has the following interface connectors:
2 x M12 (DeviceNet Micro) NMEA 2000 ® network CAN connectors
The rear panel of the device is shown in Error! Reference source not found. below.

TSM800C User's Manual
Page 10 Revision 1.0
Figure 5 –TSM800C Rear Panel
2.4.1 LAN Connection
NOTE
The LAN Connection is not necessary unless you are using any of the following
features:
Video
E-mail actions on Alerts
There is one external RJ-45 LAN connector (a second RJ-45 connector is plugged at the factory and
should not be used). The RJ-45 connector enables connection to an external network. To connect a
LAN cable with an RJ-45 connector, please follow the instructions below.
Step 1: Locate an RJ-45 connector on the bottom panel of the TSM800C.
Step 2: Align the connector. Align the RJ-45 connector on the LAN cable with the RJ-45 connector on
the bottom panel of the TSM800C. See Figure 6.
NMEA 2000®Connectors

Revision 1.0 Page 11
Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45
connector into the onboard RJ-45 connector.
Figure 6 –LAN Connection
2.4.2 USB Device Connection
There are two external USB 2.0 connectors. The USB connectors are used to transfer N2KView®
configurations between the TSM800C and other N2KView®devices, and also for applying software
updates to the TSM800C. Install the included waterproof USB bulkhead connector in a position where
it is easily accessible and plug into one of the USB connectors on the TSM800C per the instructions
below. This will make the USB connection easily accessible once the TSM800C is installed.
The USB connectors may optionally be used to install USB keyboards or USB mice for an alternative
means of controlling the TSM800C user interface.
To connect a USB 2.0 or USB 1.1 device, please follow the instructions below.
Step 1: Locate the USB connectors. The locations of the USB connectors are shown in Figure 4.
Step 2: Align the connectors. Align the USB device connector with one of the connectors on the
bottom panel. See Figure 7.
Step 3: Insert the device connector. Once aligned, gently insert the USB device connector into the
onboard connector.

TSM800C User's Manual
Page 12 Revision 1.0
Figure 7 –USB Device Connection
2.4.3 Power Connection
The TSM800C must be connected to a power source (over current protection should be provided and
should be sized in accordance with ABYC E-11, AC and DC ELECTRICAL SYSTEMS ON BOATS).
The TSM800C provides two sets of independent, galvanically isolated power connections and can
run off the power supplied by either connection, allowing for redundant power connection.
Figure 8 –Power Connections
Connect your DC power cables to the SL-SMT 09F connector block as follows:
Step 1: Unscrew (from top) or make sure that the screw terminals (square area) are fully open, so
you can secure the inserted cables correctly to the loose housing connector (it may already
be plugged into the unit as per factory installation).
Step 2: Insert cables (from front) and screw / secure the cables by turning the screw on top of the
housing to secure the cables properly. Check that the cables are firmly in place and do not
appear loose or fall out when pulling gently.

Revision 1.0 Page 13
Step 3: Plug the housing into the appropriate connector area of the unit and check again that the
cables secured conforms to the markings on the connector area of the unit.
Step 4: Finalize the installation by fasten the screws located in front on each side of the housing
connector.
2.4.4 Grounding Screw
The TSM800C is required to be properly grounded via the grounding screw located on the bottom of
the unit.
2.4.5 NMEA 2000®Connection
The two NMEA 2000®connectors can be found on the rear panel of the TSM800C. If you are using a
single NMEA 2000®network, connect either of the connectors to the NMEA 2000® network. If you are
using dual NMEA 2000®networks, connect each NMEA 2000®connector to one of the NMEA 2000®
networks. Note that if you are using dual NMEA 2000®networks, the instancing of device and data
instance on the network nodes must be unique across both networks. For example, if one network
has a device which transmits fluid level data for Fuel Tank instance 0, the other network must not
contain a device which transmits fluid level data for Fuel Tank instance 0.
The NMEA 2000®connectors are round five pin male connectors (see Figure 10). You connect the
TSM800C to an NMEA 2000®network using a Maretron NMEA 2000®cable (or an NMEA 2000®
compatible cable) by connecting the female end of the cable to the TSM800C (note the key on the
male connector and keyway on the female connector). Be sure the cable is connected securely and
that the collar on the cable connector is tightened firmly. Connect the other end of the cable (male) to
the NMEA 2000®network in the same manner. The TSM800C is designed such that you can plug or
unplug it from an NMEA 2000®network while the power to the network is connected or disconnected.
Please follow recommended practices for installing NMEA 2000®network products.
NOTE
Required polarization verification (for instance -/+ for DC power input) should
conform to the markings on the connector area of the unit. Ignoring the markings
on the unit or its add-on modules might damage the unit and/or external
equipment in which end, warranty will be void.
Figure 9 –Attaching Power Cables to Connector
Step 1
Step 2
Step 3
Step 4

TSM800C User's Manual
Page 14 Revision 1.0
Figure 10 –NMEA 2000®Connector Face Views
2.5 Power Sequencing
When the TSM800C is connected to an appropriate power source, you can use the power switch
located on the front panel to turn the TSM800C on or off. If the TSM800C is turned on, then the
switches found on the front panel will be brightly illuminated. If the power switch is pushed to power
down the TSM800C, the front panel switches will be dim.
The TSM800C can also be switched on and off by applying or removing power through an external
switch or breaker. Anytime the power is reapplied to the TSM800C, it will turn on.
The red LED on the front panel will illuminate anytime power is supplied to the TSM800C.
2.6 Configuring the TSM800C
The TSM800C will start up with the following warning screen:

Revision 1.0 Page 15
Figure 11 –TSM800C Startup Screen
The first time you start the TSM800C, N2KView®will ask you to assign it a unique name. Assigning a
unique name to the TSM800C is necessary in order to help you determine the source of alerts
generated by a TSM800C or other Maretron device capable of generating alerts.
You are required to press Accept and thereby acknowledge this warning message before N2KView®
will run in Live Mode.
Alternatively, you may Enter Demo Mode. In Demo Mode, you will not be able to connect to an
NMEA 2000®network and view live data; instead, simulated data will be provided to stimulate the
controls.
Finally, you may choose Exit, in which case the TSM800C will power off.
2.6.1 Manually Entering LAN Connection Information
NOTE
The LAN Connection is not necessary unless you are using any of the following
features:
Video
E-mail actions on Alerts
If you intend to use the Video feature or send e-mails via the Alerts feature, you must ensure that the
device can connect to your LAN (local area network). The TSM800C comes from the factory

TSM800C User's Manual
Page 16 Revision 1.0
preconfigured to obtain its LAN connection information from a DHCP (Dynamic Host Control Protocol)
server. If your local area network uses a DHCP server, no configuration is necessary, and the
TSM800C should be able to successfully connect to the local area network.
If your local area network does not use DHCP, you must manually enter the LAN connection
information into the TSM800C. This is done through the following steps:
Figure 12 –N2KView®Window with Tabs Displayed
a. Click anywhere inside the N2KView®screen to display the screen tabs as shown in Figure 12
above.
b. Click on the “Commands & Settings” tab on the right side of the N2KView®screen to display
the Commands & Settings window.
c. Click on the “Configuration” button in the Commands & Settings window to display the
Configuration dialog.
d. Click on the “Network Configuration” tab in the Configuration dialog to display the Network
Configuration dialog.