Marmitek MegaView 121 User manual

MegaView 121
20620/ 20170223 • MegaView 121™
ALL RIGHTS RESERVED MARMITEK ©
USER MANUAL 3
GEBRAUCHSANLEITUNG 9
GUIDE UTILISATEUR 15
MODO DE EMPLEO 21
MANUALE D’ISTRUZIONI 27
GEBRUIKSAANWIJZING 33
MegaView 121™

2 © MARMITEK

MegaView 121™ 3
ENGLISH
SAFETY WARNINGS
xTo prevent short circuits, this product should only be used inside and
only in dry spaces. Do not expose the components to rain or moisture.
Do not use the product close to a bath, swimming pool etc.
xDo not expose the components of your systems to extremely high
temperatures or bright light sources.
xDo not place the product in an enclosed space, such as a TV cabinet or
equivalent. Provide adequate ventilation to ensure that the product is
functioning properly and to protect against overheating.
xIn case of improper usage or if you have altered and repaired the
product yourself, all guarantees expire. Marmitek does not accept
responsibility in the case of improper usage of the product or when the
product is used for purposes other than specified. Marmitek does not
accept responsibility for additional damage other than covered by the
legal product responsibility.
xThis product is not a toy. Keep out of reach of children.
xDo not open the product: the device may contain live parts. The product
should only be repaired or serviced by a qualified expert.
xOnly connect the adapter to the mains after checking whether the
mains voltage is the same as the values on the identification tags.
Never connect an adapter or power cord when it is damaged. In that
case, contact your supplier.
1. INTRODUCTION
Congratulations on your purchase of the Marmitek MegaView 121™! The
MegaView 121™ provides a simple way to extend an HDMI (High Definition
Multimedia Interface) signal or DVI (Digital Visual Interface) over a single
CAT5e/6 Ethernet cable. Extend your HDMI cable up to 70 metres using
one CAT5e/CAT6 cable! Watch TV programmes or films and view photos
from, for example, your digital TV decoder, Media Centre PC, Blu-ray player
or hard disk recorder anywhere in the home on your TV/projection screen,
in Ultra HD quality.
All Marmitek products are manufactured with the utmost precision and are
of high quality. Please read this manual carefully and follow the instructions
to enjoy the possibilities of this product optimally.

4 © MARMITEK
2. PACKAGE CONTENTS
1x transmitter (HDMI Transmitter)
1x receiver (HDMI Receiver)
1x Infrared receiver
1x Infrared blaster LED
2x Power adapter
1x User manual
3. FEATURES
xHDBaseT technology (uncompressed HD video transmission including
4k2k Ultra HD, 1080p Full HD and all 3D formats)
xVideo bandwidth 325 MHz (enables image to be provided in 1080p, 16-
bit and 60Hz)
xDeep Color 48-bit (billions instead of millions of colours, better
reproduction of subtle gradation variances and higher contrasts).
xLPCM7.1, Dolby TrueHD & DTS HD Master Audio (high quality audio
support).
xSupports HDCP 2.2 for playing protected 4K Ultra HD content
4. CAT5e/CAT6 CABLE REQUIREMENTS
xUTP-, FTP- or STP-cable
x24AWG or lower
xSolid twisted pair
x100 ohm at 1MHz
xRJ-45 jack according to EIA/TIA T568B standard
Instead of CAT5e cable, CAT6 cable may also be applied (this offers better
quality). Use a ‘solid twisted pair CAT-5e or CAT-6 cable’ in order to
optimise transfer quality.
5. INSTALLATION

MegaView 121™ 5
ENGLISH
In order to check proper functioning of the system, it is advisable to test the
set-up first, using a short CAT-5e/6 cable.
1. Switch off all appliances before you start connecting.
2. Connect the HDMI source (Blu-ray disc player, TV Decoder, Media
Centre PC, etc.) to the MegaView 121™ transmitter [1], using an HDMI
cable (not provided).
3. Connect the MegaView 121™ receiver to the appliance shown [2] (e.g.
HDTV or projector), using an HDMI cable (not provided).
4. Use one CAT5e/6 Ethernet cable to connect the MegaView 121™’s
transmitter to the receiver [3].
Attention! The MegaView 121 cannot be connected to an existing home
network (LAN), this may cause damage to the device.
5. Connect the power adapter [4] to the ‘5VDC’ connection on the
MegaView 121™ and plug the adapter into a socket.
Attention! Do not place the MegaView 121™ transmitter or receiver in an
enclosed space, such as a TV cabinet or equivalent. Provide adequate
ventilation to ensure that the product is functioning properly and to protect
against overheating.
6. INSTALLATION IR RETURN
The MegaView 121™ has a built-in “infrared return channel”, which allows
you to operate the connected device from another room or through closed
cabinet doors using your own remote control.
1. Connect the IR receiver to the MegaView 121™receiver [5] and turn
the switch to IR IN.
xPosition it so that it is visible to your (infrared) remote control, allowing
it to receive the transmitted commands (up to 6 metres).
xThe most logical place for the IR receiver is in the vicinity of your
display device (HDTV or projector).
xBy using the supplied adhesive strip, placement is possible virtually
anywhere.
xExperiment to find the right position before definitive attachment of the
IR blaster LED.
Attention! The adhesive strip may cause discolouration on certain
surfaces, or may leave adhesive residue when removed.

6 © MARMITEK
2. Connect the IR extender cable to the MegaView 121™transmitter [6]
and turn the switch to IR OUT.
xStick the IR blaster LED near the HDMI source.
xWhen positioned correctly, one blaster LED can operate all A/V devices
within the same compartment of a cabinet.
xExperiment to find the right position before definitive attachment of the
IR receiver.
Attention! The adhesive strip may cause discolouration on certain
surfaces, or may leave adhesive residue when removed.
7. USAGE
1. Switch on the HDMI source (e.g. TV Decoder or Media Centre PC).
2. Switch on the display device (for instance HDTV or projector) and
select the appropriate input. Usually you will do this by pressing the A/V
or EXT button of your remote control.
3. You will receive images from the connected A/V device immediately.
4. The MegaView 121™ can also be used to operate the HDMI source
from another room, by pointing your own remote control at the IR
receiver and pressing a button.

MegaView 121™ 7
ENGLISH
8. TECHNICAL INFORMATION
Video
Data transmission HDBaseT
Supported HDTV resolutions 480p, 576i, 576p, 720p, 1080i, 1080p,
[email protected]/24Hz
Ondersteunde 3D formaten [email protected]/24Hz,
[email protected]/60/50Hz
Maximum Pixel Frequency (max) 325 MHz
Maximum Bit Rate (max) 3.4 Gbps (10.2 Gbps per channel)
Audio
Supported audio formats LPCM 7.1CH, Dolby TrueHD and DTS-
HD Master Audio
Transmitter
HDMI input 1 HDMI (19-pin female)
TX LAN RJ45, EIA/TIA T568B
Maximum CAT5e/6 cable length 70m@720p, 60m@1080p, 40m@4k2k
Receiver
HDMI output 1 HDMI (19-pin female)
RX LAN RJ45, EIA/TIA T568B
IR Receiver
Frequency range: 30 - 60 KHz
IR reception range: ± 6 metres
Connection: 3.5mm jack plug
Kabellengte: 100 cm
Casing transmitter / receiver
Dimensions (H x W x D) 93 mm x 49 mm x 25 mm
Weight 135 g
Environment
Ambient temperature +0 to +70° C
Ambient humidity 10% to 85%
Power
Input 100-240VAC @50-60Hz
Output 5VDC 1A
Specifications may change without prior notice.

8 © MARMITEK
9. FREQUENTLY ASKED QUESTIONS
Bad (or no) image and sound
xCheck if the A/V device is switched on.
xUse only CAT5e/CAT6 cable as specified in chapter 4 (CAT5e Cable
Requirements).
xCheck if the CAT5e/CAT6 cable provides a solid connection (no cable
faults).
xCheck if the RJ-45 has been connected according to the EIA/TIA
T568B standard.
xPlease ensure that the maximum cable length is not exceeded.
xInstall your system as far away from any RF sources (wireless devices)
as possible.
xSet a low resolution on your HDMI source. The CAT5e/6 cable used
probably cannot deal with the higher resolution bandwidth.
Do you have any questions that are not answered above?
Please check www.marmitek.com.
Environmental Information for Customers in the European Union
European Directive 2002/96/EC requires that the equipment bearing this symbol on
the product and/or its packaging must not be disposed of with unsorted municipal
waste. The symbol indicates that this product should be disposed of separately from
regular household waste streams. It is your responsibility to dispose of this and other
electric and electronic equipment via designated collection facilities appointed by the
government or local authorities. Correct disposal and recycling will help prevent potential negative
consequences to the environment and human health. For more detailed information about the
disposal of your old equipment, please contact your local authorities, waste disposal service, or
the shop where you purchased the product.

MegaView 121™ 9
DEUTSCH
SICHERHEITSHINWEISE
xUm Kurzschluss vorzubeugen, dieses Produkt bitte ausschließlich
innerhalb des Hauses und nur in trockenen Räumen nutzen. Setzen
Sie die Komponenten nicht Regen oder Feuchtigkeit aus. Nicht neben
oder nahe eines Bades, Schwimmbades usw. verwenden.
xSetzen Sie die Komponente Ihres Systems nicht extrem hohen
Temperaturen oder starken Lichtquellen aus.
xDas Produkt nicht in einem geschlossenen Schrank wie
Fernsehschrank oder Ähnliches nutzen. Sorgen Sie in Bezug auf die
Funktionstüchtigkeit und zum Schutz gegen Überhitzung des Produktes
für eine adäquate Ventilation.
xBei einer zweckwidrigen Verwendung, selbst angebrachten
Veränderungen oder selbst ausgeführten Reparaturen verfallen alle
Garantiebestimmungen. Marmitek übernimmt bei einer falschen
Verwendung des Produkts oder bei einer anderen Verwendung des
Produktes als für den vorgesehenen Zweck keinerlei Produkthaftung.
Marmitek übernimmt für Folgeschäden keine andere Haftung als die
gesetzliche Produkthaftung.
xDieses Produkt ist kein Spielzeug. Außer Reichweite von Kindern
halten.
xDas Produkt niemals öffnen: Das Gerät kann Teile enthalten, worauf
lebensgefährliche Stromspannung steht. Überlassen Sie Reparaturen
oder Wartung nur Fachleuten.
xSchließen Sie den Netzadapter erst dann an das Stromnetz an,
nachdem Sie überprüft haben, ob die Netzspannung mit dem auf dem
Typenschild angegeben Wert übereinstimmt. Schließen Sie niemals
einen Netzadapter oder ein Netzkabel an, wenn diese beschädigt sind.
In diesem Fall nehmen Sie Kontakt mit Ihrem Lieferanten auf.
1. EINFÜHRUNG
Herzlichen Glückwunsch zum Erwerb des Marmitek MegaView 121™! Der
MegaView 121™ macht es auf einfache Weise möglich, ein HDMI (High
Definition Multimedia Interface) Signal oder DVI (Digital Visual Interface)
über nur ein CAT5e/6 Ethernetkabel zu verlängern. Verlängern Sie Ihr
HDMI Kabel auf ganze 70 Meter über nur ein CAT5e/CAT6 Kabel! Schauen
Sie Fernsehprogramme, Filme und Fotos von Ihrem digitalen TV Decoder,
Media Center PC, Blu-Ray-Disk oder HDD Rekorder in optimierter HD
Qualität anderswo auf Ihrem TV/Projektionsschirm.
Die Produkte Marmiteks werden mit großer Sorgfalt hergestellt und sind von
hoher Qualität. Lesen Sie diese Anleitung bitte sorgfältig durch und
befolgen Sie die Anweisungen, um die Möglichkeiten dieses Produkts
optimal nutzen zu können.

10 © MARMITEK
2. VERPACKUNGSINHALT
1x Sender (HDMI Transmitter)
1x Empfänger (HDMI Receiver)
1x Infrarot-Empfänger
1x Infrarot Blaster LED
2x Speisungsadapter
1x Gebrauchsanleitung
3. EIGENSCHAFTEN
xHDBaseT Technologie (unkomprimierte HD Videoübertragung inklusive
4k2k Ultra HD, 1080p Full HD und alle 3D Formate).
xVideobandbreite 325 MHz (ermöglicht Bildwiedergabe von 1080p, 16-
BIT und 60Hz).
xDeep Color 48-Bit (Milliarden anstatt Millionen Farben, bessere
Wiedergabe von subtilen Farbwerten und höheres Kontrastverhältnis).
xLPCM7.1, Dolby TrueHD & DTS HD Master Audio (hohe Qualität
Audio-Unterstützung)
xUnterstützt HDCP 2.2 zum Abspielen von gesichertem 4K Ultra-HD
Inhalt
4. ANFORDERUNGEN CAT5e/CAT6 KABEL
xUTP-, FTP- oder STP- Kabel
x24AWG oder niedriger
xSolid Twisted Pair Kabel
x100 Ohm bei 1MHz
xRJ-45 Anschluss gemäß der EIA/TIA T568B Norm
Anstatt eines CAT5e Kabels kann auch ein CAT6 Kabel verwendet werden
(dieses ist von besserer Qualität). Zur Optimierung der Übertragungsqualität
nutzen Sie dann “Solid Twisted Pair CAT-5e oder CAT-6 Kabel.
5. INSTALLATION