Martin-Till UMO-WA1345 User manual

APPLIES TO ALL 1345 ROW CLEANER with UNIT MOUNTED FERTILIZER OPENER
Martin Planter Attachments
Martin Industries LLC
206 Elk Fork Road
Elkton, KY 42220
Telephone: [phone]
E-Mail: [e-mail]
www.martintill.com VERSION 01 17 2019
INSTALLATION INSTRUCTIONS
UMO-WA1345
SHOWN WITH DS MOUNT AND OPTIONAL SMARTCLEAN CYLINDER
AND BRACKETS, RAZOR WHEEL(RTW1412.5) , SIDE TREADER WHEELS
( STW - 04 ) & CAM ADJUST (CA03 - 1345)

STEP 1 : ATTACH THE MOUNT TO THE PLANTER
1
The Martin-Till Unit Mounted Fertilizer Opener (UMO — 100) allows you to place fertilizer in three
different horizontal (offset), and three different vertical (depth), distances from the seed .
The options on STEP 2A determine the vertical distance from the seed (depth).
The options on STEP 2B determine the horizontal distance from the seed (offset).
STEP 2A: UMO —100 DEPTH SETTING OPTIONS
Select one of the following UMO vertical installation positions (A, B, or C)
Position A:
The top bolt passes through the first holes of the mount and the UMO. The bottom bolt passes
through the fifth hole of the mount and the forth hole of the UMO. This position will place the ferti-
lizer 3/4” above seed depth.
Position B: (RECOMMENDED)
The top bolt passes through the second hole of the mount and the first hole of the UMO. The bot-
tom bolt passes through the fifth holes of the mount and the third hole of the UMO. This position
will place the fertilizer “even” with seed depth.
Position C:
The top bolt passes through the third hole of the mount and the first hole of the UMO. The bottom
bolt passes through the fifth holes of the mount and the second hole of the UMO. This position will
place the fertilizer 3/4” below seed depth.
STEP 2 : DETERMINE DESIRED FERTILIZER PLACEMENT
Use a square or a level tool to make sure that the planter base plate is set parallel to the Planter’s
W-Bracket (The bracket that attaches the planter to the tool bar).
Using four 1/2” X 1 1/2” bolts, attach the Mount to the Planter’s base plate, and torque mounting
nuts to 57 ft-lbs ( Right Picture).
For CaseIH 1200 series planter, use provided two 1/2” X 3 1/2” Grade 8 bolts and nuts . Torque to
80 ft-lbs ( Left picture).
1/2” X 1 1/2”
Bolts
DU Mount
Shown
1/2” X 3 1/2”
Bolts
CU Mount
Shown

2
Position A
3/4” above seed depth
Position B
Even with seed depth
(Recommended)
Position C
3/4” below seed depth

STEP 2B: UMO —100 OFFSET SETTING OPTION
Three different offset settings are shown in the pictures. The UMO can be installed to the right side
(Offset 1” from seed furrow), in between (Offset 2” from seed furrow), or to the left side (Offset 3”
from seed furrow) of the mount flanges. Place the UMO-12 spacer bar according to the pictures.
Select one of the following UMO horizontal installation positions (A, B, or C)
3
NOTE:
*Recommendaons based on general rule of
thumb of 1” oset for every ten gallons of ferliz-
er applied per acre.
*Consult with your agronomist for specic appli-
caon rate informaon unique to your operaon,
soil properes, and condions.
Position A: Offset 1” from seed furrow
*Recommended for fertilizer application rates of
10 GPA and under.
UMO in the Le side
Spacer Bar in the middle
Position C: Offset 3” from seed furrow
*Recommended for fertilizer application rates of 20-
30 GPA.
UMO in the Right side
Spacer Bar in the middle
Position B: Offset 2” from seed
furrow
*Recommended for fertilizer application
rates of 10-20 GPA.
UMO in the Middle
Spacer Bar in the Right side

4
SETTING #2: This configuration provides
medium ground pressure.
SETTING #3: This configuration provides
the least ground pressure.
NOTE: This is the default and recom-
mended position.
STEP 2C: FURROW CONTROL LEVER GROUND PRESSURE ADJUSTMENT
SETTING #1: This configuration provides
maximum ground pressure.

5
After selecting the desired depth and offset settings, attach the UMO-100 to the mount using two 1/2” X 3”
flange bolts, and Flange locknuts, provided for you. If you purchased the optional SmartCean System, you
will install the SmartClean cylinder top brackets on the side of the mount flanges. Use the 1/2” X 3 1/2” bolts
provided in place of the 3” bolts. The SmartClean cylinder top brackets are available in right and left sets.
*The right set mounts on the left UMO-100 and the left set mounts on the right UMO-100. The correct con-
figuration will bring the bracket pin point to the center of the row cleaner.
Torque the bolts to 80 ft-lbs.
*NOTE: Confirm half of UMO’s are left sided and half are right sided for proper planter drafting.
STEP 3 : ATTACH UMO-100 TO THE MOUNT
Right UMO-100 and Left SmartClean Cylinder
top bracket set are shown
SmartClean BRACKET SET (SC-CUB-2L)

STEP 4 : ATTACH 1345 FRAME ASSEMBLY TO THE MOUNT
IMPORTANT: Stop arm installation, as shown in the picture, is for the right UMO configuration . For a left
UMO configuration, install the right stop arm (STARM1360-5-8R) on the opposite side.
1. Align the holes in the mount and the frame assembly. Insert the 5/8” x 2 1/2” and the 5/8” x 2” bolts
from the outside. Add the Stop Arm and other 5/8” x 2” bolt as it is shown in the picture. Place the
bushings (BU7858) and nuts on the 5/8” x 2” bolt and on the 5/8” x 2 1/2” bolt from inside.
2. Tighten the three bolts to 112 ft-lbs. Check after first day of use.
3. Check to ensure the frame is not binding on the mounting bracket and is free to float up and down.
4. Install the 5/8” X 3” bolt on the Stop Arm as threaded adjustment assembly and tighten the 5/8” Thin
Nut to lock it after the adjustment.
6
5/8” FLANGE LOCKNUT
(NFSL007)
5/8” X 2”
FLANGE BOLT
(BFS0152)
5/8” X 2 1/2” FLANGE
BOLT (BFS0154)
STOP ARM
(STARM1360-5-8L)
5/8” THIN NUT (NHSJ013)
5/8” X 3” BOLT (BHS0543)
BUSHINGS
(BU7858)
5/8” X 2” FLANGE
BOLT (BFS0152)

INSTALL OPTIONAL CAM ADJUSTMENT ASSEMBLY
1. Mount the cam block to the frame using the three 3/8” buon head bolts.
2. Slide the 1/2” x 3 1/2” bolt through the knob, spring, and support block and thread it into the cam.
3. Tighten the bolt unl the cam is directly adjacent the support block but sll loose enough to be disengaged from
the pin by pushing on the knob.
4. Install the 1/2” nut on the end of the bolt and ghten securely against the cam. Torque to 57 -lbs.
7
1/2” FLANGE NUT
(N12CFL)
CAM
(CA-30)
CAM BLOCK
(CA-31-1345R/L)
RH SHOWN
BUTTON HEAD
BOLT X 3
(B5B381)
KNOB
(CA-32)
1/2” X 3 1/2” BOLT
(B5M12CN312)
SPRING
(CA-34)

STEP 5 : DETERMINE THE BEST WHEEL CONFIGURATION FOR
YOUR SOIL CONDITIONS
OPTION A: INTERSECTED
(Both wheels in front hole)
Both wheels forward provides maximum cleaning effect. The interlocked wheels till the middle of
the seed row.
OPTION B: OFFSET
(Left wheel in front hole and right wheel in rear hole)
The staggered configuration allows the toothed wheels to turn more easily in loose soil.
With this configuration, we suggest running the left wheels in the rear hole on one half of the
planter and the right wheels in the rear hole on the other half of the planter (when viewed from
behind).
8

9
STEP 6: INSTALL WHEEL ASSEMBLIES
1) Assemble the bearing retainer, hub, wheel, and side treader wheel (if used) as shown using the 4
bolts (BCS0123) and flange nuts (NSFL003) Torque the bolts to 23 ft-lbs, and retighten after the
first days use
2) Install the assembled wheel unit by passing the flange bolt (BFS0156) through the bearing center
and washer (WN0064) and attach to the frame using the flange nut (NSFL007), tighten to 116 ft-
lbs.
(NOTE: When using deflector (scraper) refer to step 7 before completing the installation)
3) The wheel marked TW3813-L4 (Or RTW1412.5-L4 for the Razor wheel) is for use on the left side
of the frame (as viewed from behind the machine). Repeat for opposite side.
DUST CAP
(HS1328)
5/8” X 3
FLANGE BOLT
(BFS0156)
3/8” FLANGE
NUTS
(NSFL003)
OPTIONAL SIDE TREADER
WHEEL
(STE-04A)
HUB
(CHU44-B2)
BEARING RETAINER
(BC-01)
WHEEL (LEFT)
(OPTIONAL RTW1412.5L4 SHOWN)
WASHER
(WSN0064)
FLANGE NUT
(NFSL0007)

STEP 7: INSTALL OPTIONAL DEFLECTOR (SCRAPER)
NOTE: The Deflector (Scraper) is recommended when operating in wetter conditions, or damp
stringy residue, to reduce wrapping.
NOTE: The Deflector (Scraper) comes in pairs of left and right for left and right wheels.
Intersected Configuration ( Wheel in front hole)
1) Place the deflector (Scraper) on the back of the assembled wheel unit (previously assembled in
step 6) as shown here and pass the flange bolt (BFS0156) through the wheel assembly and the
deflector and attach the flange nut (NFSL007) hand tighten and locate the deflector as shown
and torque the flange bolt (BFS0156) to 116 ft-lbs being careful not to allow the deflector to ro-
tate during bolt tightening.
2) The wheel marked TW3813-L4 (Or RTW1412.5-L4 for the Razor wheel) is for use on the left side
of the frame (as viewed from behind the machine). Repeat for opposite side.
NOTE: When the deflector (scraper) is to be installed the washer (WSN0064) is NOT used
10
DEFLECTOR
(SCRAPER)
(ITD STW L)
(SHOWN IN CORRECT
POSITION)
FLANGE BOLT
(BFS0156)
FLANGE NUT
(NFSL007)

Offset Configuration ( Wheel in rear hole)
1) Place the deflector (scraper)on the back of the assembled wheel unit (previously assembled in
step 6) as shown here and pass the flange bolt (BFS0156) through the wheel assembly and the
deflector using the rear hole in the frame unit and attach the flange nut (NFSL007) hand tighten
and locate the deflector (scraper) as shown and torque the flange bolt (BFS0156) to 116 ft-lbs
being careful not to allow the deflector to rotate during bolt tightening.
2) The wheel marked TW3813-L4 (Or RTW1412.5-L4 for the Razor wheel) is for use on the left side
of the frame (as viewed from behind the machine). Repeat for opposite side.
NOTE: When the deflector (scraper) is used the washer (WSN0064) is NOT used
11
FLANGE BOLT
(BFS0156
REAR HOLE
FLANGE NUT
((NFSL007) NOT
SHOWN)

STEP 8 : INSTALL THE OPTIONAL SMART CLEAN CYLINDER
Install the SmartClean cylinder between the top bracket (LH =SC-CUB-1345-2L / RH =SC-CUB-1345-
2R.) and the integral bottom mount point supplied. Use pins as shown in the picture below.
NOTE: Cylinder may be installed with elbow fittings in either up or down orientation, depending on
user preference.
13
7/16” PIN &
COTTER PIN
3/8” PIN & COTTER PIN
( SC-LP38 )
SMARTCLEAN CYLINDER
(SC-CYL-2X2 )
SMARTCLEAN TOP
BRACKET
( SC-CUB-1345-2L
SHOWN )
INTEGRAL BOTTOM
MOUNT

PARTS LIST FOR 1345 HUB ASSEMBLY (CHU44-B2)
14
BEARING
(5203KMF)
BEARING RETAINER (BC-01)
DUST CAP (HS1328)
HUB (HU44-B2)

PARTS LIST FOR UMO-100
UMO — 100R shown, UMO — 100L (not shown) is the opposite side
NOTE: UMO-100R SHOWN
• R DESIGNATES RIGHT HAND PARTS
• L DESIGNATES LEFT HAND PARTS
SHOE (UMO-O41R)
3/8” FLANGE NUT
(N38CFL)
5/16” X 1” BOLT
(BSC5161)
SPACER BAR (UMO-12)
UMO BEAM
(UMO-MSB01R)
5/16” X 1 1/2”
FLANGE BOLTS
(B5F516NC112)
5/8” NUT
(N58)
TRANSITION WASHER
(UMO-BSH01)
LEVER (UMO-FCL01)
5/16” NUT (N516FLN)
BRACKET
(UMO-FCB01R)
FURROW CONTROL STRAP
(UMO-FCS01)
REINFORCEMENT
STRAP (UMO-FCS02)
5/16” FLANGE NUT
(N516FLN)
5/8” LOCK
NUT
(N58CNL)
SEAL (CR14971)
SEAL (CR14971)
RACE (L44610)
SPRING (UMO-SPG01R)
AXLE (UMO-A77)
BEARING (L44643)
RACE (L44610)
BLADE (UMO-BLD01)
BEARING
(L44643)
3/8” X 1”
CARRIAGE BOLT (B5C381)
HUB (HU44-F)
1/2” X 3” FLANGE BOLT
(B8F12NC3)
1/2” NUT (N12FLN)
5/8” THIN LOCK NUT (N58CNLT)
NOTE: Install the blade with
bevel facing hub.
ANGLED GREASE FEEDER (GF-1A)
15

MAINTENANCE TIPS
UMO — 100 Hub Preventative Maintenance
The UMO hub is designed to be “flushed out” with lubrication, without damaging the triple lip seal.
To flush the hub, lubricate until fresh grease is visible around the seal.
• In worked ground, lubricate every 20 hours of run time
• In No-Till ground, lubricate every 40 hours of run time
NOTE: Hubs may feel tight when first installed. They will loosen after they “run in”.
UMO — 100 Hub Bearing Preload Adjustment
Maintaining proper bearing preload is crucial to bearing life. Monitor and adjust annually.
To adjust:
• Loosen the 5/8” thin lock nut
• Tighten the 5/8” regular nut until you feel zero end play
• Gently back the nut off, leaving .01” - .012” end play
• Hold the 5/8” regular nut in place with a wrench and tighten the 5/8” thin lock nut
NOTE: End play is checked by pulling out on the top of the blade while pushing in on the bottom
16
Grease fitting on
UMO-100
5/8” thin lock nut
and 5/8” regular nut

EXPLODED VIEW FOR UMO-WA1345
17

PARTS LIST FOR UMO-WA 1345
18
Note: Item 2 and 3 may substute with 1/2” X 1 1/2” Bolt and 1/2” nut.
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 MT1360DU-W MOUNT 1 2 87698852 M12 X 40 CARRAIGE BOLT 10.9ZND 4 3 87681209 M12 FLANGE BOLT 10ZND 4 4 UMO-100R/L RIGHT/LEFT UMO UNIT 1 5 WA1345R/L RIGHT/LEFT ROW CLEANER 1 6 UMO-012 SPACER BAR 1 7 SC-CUB-1345-2R/L R/L SMARTCLEAN TOP BRACKET SET 1 8 STARM1360-5-8R/L R/L STOP ARM 1 9 BU7858 7/8" X 5/8" BUSHING 2
10 BFS0152 5/8" X 2" FLANGE BOLT GR8 2 11 BFS0154 5/8" X 2 1/2" FLANGE BOLT GR8 2 12 NFSL0007 5/8" FLANGE NUT GR8 3 13 BFS0187 1/2" X 3 1/4" FLANGE BOLT GR8 2 14 NFS0005 1/2" FLANGE NUT GR8 2 15 BHS0543 5/8" X 3" ADJUSTMENT BOLT 1 16 NHSJ013 5/8" THIN NUT 1 17 CA-03-1345 R/L CAM ASSEMBLY 1

Martin Industries LLC
206 Elk Fork Road
Elkton, KY 42220
Telephone: [phone]
E-Mail: [e-mail]
The most trusted name in no-till
Established 1991