Martin GRANDEUR 91-02606115 Operation instructions

GRANDEUR Model’s
91-02606115 & 91-02609115
YOU WILL FEEL A SLIGHT
“BOUNCE-BACK” WHEN YOU SIT DOWN.
THIS IS NORMAL: NOT A DEFECT.
THE PNEUMATIC CYLINDER FOR THE
SEAT HEIGHT ADJUSTMENT REACTS
TO YOUR WEIGHT BY GIVING A LITTLE
IMPORTANT NOTICE
Assembled
92-02609115
Assembled
92-02606115
PARTS
A. [1] Base Plate Mechanism
B. [1] Cylinder
[a] 91-7706 model
[b] 91-7709 model
a.
b.
C. [5] Castors
D. [1] Plastic Ring insert
Model 92-02609 only
(This part can be found in
the foot ring Part F)
E. [1] 5-Star Base
F. [1] Foot ring with knob
Model 92-02606 only
H. [1] Seat
I. [1] Black Cylinder Bellows
Model 92-02609 only
IMPORTANT
If you have difficulty assembling your chair or need customer service assistance.
Please call: Martin Universal Design, Inc. Customer Service Hot Line at
1-313-895-0700. If you need additional parts, it is not necessary to contact your
dealer, our Customer Service Rep. will forward them to you immediately.
4444 Lawton Avenue, Detroit MI 48208 USA
Tel:[phone] • Fax:[phone]
E-mail: [email protected]
Visit us at: www.MartinUniversalDesign.com
J. [6] 1-1/8” Hex Head Screws
& [6] washers
K. [4] 1.5” Hex Head Screws
& [8] washers for Armrests
L. [4] 3/4”
Plastic Washers
for armrest attachment
G. [1] Backrest
M. [2] Armrests
Revised 03/2009 RPI

Place 5-star base (E) face down
and push [5] castors (C) into each
position.
1.
C
E
THIS STEP IS ONLY FOR
MODEL 92-02606 ONLY.
Before attaching foot ring (F) to
cylinder (B). Begin by loosening the
knob on the foot ring and make sure
the plastic ringis inserted properly,
by making sure the cut ends of the
insert run parallel with the weld on
the inside of the foot ring hole. The
insert should be already in the foot
ring. NOTE: THIS MUST BE
POSITIONED PROPERLY TO
ALLOW THE CYLINDER TO SLIDE
THROUGH THE INSERT EASILY.
knob on foot ring
Cut ends of plastic insert must
run parallel with the weld.
weld
Slide cylinder down through foot
ring and tighten knob. After chair is
assembled completely, you may
adjust foot ring to desired height.
2.
3.
PLEASE NOTE: If you have model
number 92-02609, your assembly
will be the same but instead of foot
ring you will need to place black
bellows over top of cylinder after
inserting cylinder into base.
Insert wider end of cylinder into hole
in base, as shown above.
Model #
92-02609
Model #
92-02606
4.
Attach mechanism (A) to seat (H)
using [4] 1.5” hex head screws (J).
See picture above for specified
locations that are circled. Tighten
with hex wrench.
H
A
5.
6.
Attach backrest (G) to seat
mechanism (A), by inserting backrest
support bar into oval hole in
mechanism. Tighten knob on
mechanism to secure.
G
A
Revised 03/2009 RPI
Attach armrests to bottom side of
seat. Each Armrest (M) uses [3]
screws and [3] washers. Use [1]
1-1/8” screw and 1washer in location
indicated above. Use [2] each 1.5”
screws, [2] washers and [2] thick
plastic washers in location show
above. Tighten with hex-wrench.
NOTE: [2] Thick plastic washers
are to be positioned between
the armrest and seat bottom,
for each armrest. See below
illustration for proper locations.
7.
1-1/2”
1-1/2”
1-1/8” 1-1/8”
Screw
Metal
washer
Armrest
bracket
Plastic
Washer
Seat
Bottom
8.
Attach seat/backrest/armrest
assembly to cylinder by inserting
top of cylinder into hole on bottom
of seat mechanism. Weight of sitting
on seat will secure seat assembly to
cylinder.
NOTE: 2 Paddles below seat are for seat
height adjustment & Backrest tilt adjust-
ments.
NOTE2: PERIODIC RE-TIGHTENING of Armrests
screws may be needed throughout use of
chair over the years.