Martin U-DS40 User manual

4444 Lawton Avenue, Detroit, MI 48208 USA • Tel:[phone]/Fax:[phone]
Email: [email protected] • visit us at ww
w.MartinUniversalDesign.com
U-DS40 SMART TABLE • Assembly Instructions
IMPORTANT
If you have difficulty assembling your U-DS40 Smart Table or need customer service assistance.
Please call: Martin Universal Design, Inc. Cu stomer Service Hot Line at 1-313-895-0700.
If you need additional parts, it is not necessary to contact your dealer , our Customer Service Rep.
will forward them to you immediatel y.
03/2009- RPI
Parts List
[1 ea] - 24” x 36” Top [2 ea] - Top & Base Supports
Pg. 1
ABC
[2 ea] - Legs
[1 ea] -Base Cross Support [4 ea] - Feet
D F
[2 ea] - Upper Legs
E
[2 ea] - Collars [2 ea] - Tilt Arms
G I
[1 ea] - Pencil Edge
H
J LK
[2 ea] - Knobs [8 ea] - Screws (5x30mm) [6 ea] - Allen Bolts (6x40mm)
MO N
[2 ea] - Allen Bolts (6x20mm) [2 ea] - Screws [4 ea] - Nuts
P1 QP2
[4 ea] - Large Washer [2 ea] - Small Washer [1 ea] - Wrench
NOTE: READ ALL ASSEMBLY INSTRUCTIONS FIRST
BEFORE ATTEMPTING TO ASSEMBLE U-DS40 SMART TABLE.
- TWO PEOPLE NEEDED FOR
TABLE ASSEMB L
Y -
[1 ea] - Allen Wrench
R

03/2009- RPI
STEP 1] Attach Base supports to Top
FIG 1
Pg. 2
U -DS40 SMART TABLE • Assembly Instructions
IMPORTANT:
ASSEMBLE TABLE ON FLAT CARPETED
SURFACE TO PROTECT TOP FROM MARRING
Make sure the base
supports are
positioned so that the
tab is on the outer
side of the base
support.
See image to the left
FIG 1b.
STEP 2] Attach Upper Legs
Begin by taking your table top (part A) and lay it face
down onto your flat carpeted work surface
(holes facing up). Take [2 each] Base Supports
(part B) and position them so that they line up with the
holes in the top and metal tab is positioned on the outer
side of the base support.
See FIG 1b.
Using [4 each] 5x30mm Screws (part K) per base
support. Secure by tightening these screws to secure
base support to top. Repeat with second base support
(part B).
To attach the upper legs (part F) to the base supports
(part B), line up the hole found in the upper leg with the
welded brace found on the base support. Line up the
holes, insert a 6x40mm Allen Bolt through the welded
brace then through the upper leg and then through
the other side of the welded brace add a nut (part O).
Tighten to secure.
See FIG 2 & 2b.
Repeat with second upper leg.
FIG 2
FB
L
O
welded brace
welded brace
F
B
L
O
FIG 2b
K
K
K
K
A
BB
FIG 1b

03/2009- RPI
FIG 3
Pg. 3
FIG 5
U-DS40 SMART TABLE • Assembly Instructions
STEP 3] Attach Adjustable Rubber Feet
Attach the [4] adjustable rubber feet (part E) to Legs
(part C) by threading the rubber feet clockwise into the
bottom holes of the legs. See Fig 3 images.
NOTE: To adjust the level of the base once assembled,
unscrew or tighten each rubber foot until table is level.
C
E
FIG 4
STEP 4] Base Assembly
Take the [2] legs (part C) that have the rubber feet
attached and the [1] Base cross support (part D).
Attach the base support (part D) to each leg using [2
each] 6x40mm Allen bolts (part L) to each leg. Line up
holes in the legs to the ends of the base support. Insert
bolt through outer side of legs and into holes on end
of base Support.
Tighten bolts with Allen Wrench.
See FIG 4
D
CC
E
C
L
GSTEP 5] Attach Collars to Base Legs
Zoom of Bolt attachment
Attach the [2 each] Collars (part G) to the top ends of
the legs as shown in the picture in FIG 5.
Make sure the knob is positioned on the outer side
of the legs.
NOTE: Loosen the knob on the collar (part G) prior
to sliding the collar down over the legs (part C).
L
C

6

HEIGHT ADJUSTMENT:
To adjust the height of your table - loosen the knobs on the collars found on the base of the table and lift the table top to
desired height.
TILT ADJUSTMENT:
To adjust the tilt of your table top, loosen the knobs on the side of the legs and hold onto table top and tilt to desired angle.
Tighten knobs on legs to secure.
LEVELING FLOOR GUIDES:
If your floor is uneven, you can adjust the floor guides by loosening the floor guides
to make up for the uneven floor.
4444 Lawton Avenue, Detroit, MI 48208 USA • Tel:[phone]/Fax:[phone]
Email: [email protected] • visit us at www.MartinUniversalDesign.com
03/2009- RPI
Pg. 5
U-DS40 SMART TABLE • Assembly Instructions
Attach Pencil Ledge (part I) to the front edge of the Top
using [2] Screws (part N). Tighten to secure.
NOTE: Slightly loosen screw to allow for raising or
lowering of pencil ledge.
SEE FIG 9 & FIG 9B
STEP 9] Attach Pencil Ledge
FIG 9B - ZOOM of Pencil Ledge attachment
FIG 9
STEP 10] Tighten All Screws and Bolts
Once complete, double check all screws and bolts to
make sure they are secure.
Enjoy Your New SMART TABLE!