Martin U-DS1922W User manual

1
MANCHESTER SPLIT TOP
TABLE ASSEMBLY INSTRUCTIONS
IMPORTANT
If you have difculty assembling your table, or need customer service
assistance, please call: Martin Universal Design, Inc. customer service
hotline at 1-313-895-0700, or email at [email protected]. If
you need additional parts, it is not necessary to contact your dealer. Our
Customer Serice Representative will forward them to you immediatly.
U-DS1922W

2
Left Leg
Cross Support
(Back Top)
Tilt Mechanism
Right Leg
Cross Support
(Back)
Drawer Handle
Cross Support
(Bottom)
Drawer Support
Hinge
(QTY: 2)
Cross Support
(Bottom)
Drawer Top
Bolt 6 x 50mm
(QTY: 14)
Bolt 6 x 8mm
(QTY: 2)
Locking Nut
(QTY: 2)
Screw 4 x 12mm
(QTY: 3)
Pencil Ledge
Bolt 6 x 28mm
(QTY: 6)
Bolt 4 x 20mm
(QTY: 2)
Cam
(QTY: 4)
Screw 4 x 14mm
(QTY: 8)
Drawer Stopper
Composite Bolt
(QTY: 4)
Drawer Back Panel
Drawer Front Panel
Metal Washer
(QTY: 2)
Drawer Right Side Panel
Metal Washer
(QTY: 4)
Drawer Left Side Panel
Glides
(QTY: 4)
Drawer Bottom Panel
Allen Wrench
Screw 4 x 35mm
(QTY: 4)
Wrench
Cross Support
(Front Top)
Main Top
Phillips Head Screwdriver NOT included.
PARTS LIST
1
11
21
6
16
26
31
2
12
22
7
17
27
32
3
13
23
8
18
28
33
4
14
24
9
19
29
34
5
15
25
10
20
30
35
= Table Components = Fasteners and Tools
June2013

3
Step 1
Step 3
Step 2
Assemble Glides
Attaching Drawer Support
Assemble Table Base
Attach 4 oor glides (Part 33 ) to the left and right legs (Part 1
& 2 ) by tightening the glides into the specied holes at the bot-
tom.
Attach Drawer support guide (Part 8 ) to the base cross supports (Parts 5
and 6 ) using 1 each 6 x50mm hex bolts (Part 14 ) and metal washers
(Part 31 ). Tighten with Allen Wrench (Part 34 ).
A) Attach the 5 cross supports (Parts 3 4 5 6 7 ) to the left leg
(Part 1 ) by lining each up with appropriate hole. Secure each to outside
edge of Part 1 with one 6x50mm hex bolt (Part 14 ) into each hole.
Tighten hex bolts with Allen Wrench (Part 34 ).
B) Repeat with right side (Part 2 ) by attaching the other end of
the 5 cross supports (Parts 3 4 5 6 7 ) also using one each of
6x50mm hex bolts (Part 14 ) into each hole on the outside side edge of
Part 2 , lining that hole up with the hole in the end of each cross support.
Tighten bolts with Allen Wrench (Part 34 ).
12
5 6
3
7
1
2
4
14
33
14
14
31
8
6
5
June2013

4
Step 4
Step 5
Attach Tilt Mechanism and Hinges
Attach Top Drawer
A) Attach Tilt mechanism (Part 11 ) to the base. Locate the 2 holes on the top side of cross support (Part 6 ) .
Secure Tilt Mechanism to this cross support using 2 each 6x28mm bolts (Part 15 ) & 2 each locking nuts (Part 21 ).
Position locking nuts to the underside of cross supports (Part 6 ). Use wrench (Part 35 ) to hold nuts while tightening
down Hex Bolts.
B) Attach 2 hinges (Part 13 ) to front edge of cross support (Part 5 ) by lining up holes in hinge and holes in
cross support bar (Part 13 ). Secure using 2 each 4x14mm screw (Part 19 ) per hinge. Tighten with Phillips head
screwdriver.
Line up the drawer top (Part 9 ) to the specied holes on table base. Once drawer top is positioned correctly, secure top
using 4 of 6x28mm bolts (Part 15 ) and 4 of the metal washers (Part 32 ). The metal washers should be positioned
between drawer top and table base.
15
21
19
19
11
13
13
32
15
9
June2013

5
Step 6
Attach Main Top
A) Align holes in hinges to the holes in top board. Attach the 2 hinges (Part 13 ) to the top by using 2 each 4x14mm
screws (Part 19 ) per hinge and tighten with Phillips head screwdriver.
B) B) Align holes in tilt mechanism (Part 11 ) to threaded holes in top. After lining up holes, attach tilt mechanism to top
with 2 each 6x8mm Hex Bolts (Part 16 ) and tighten with Allen wrench.
19
13
13
16
11
10
June2013

6
Step 7
Drawer Assembly
A) Take the back panel (Part 25 ) and side panels of the drawer (Parts 27 & 28 ) and To secure drawer assembly,
insert 2 each 4x35mm screws (Part 30 ) into each drawer side panel and tighten with Phillips head screwdriver.
B) Slide the drawer bottom (Part 29 ) into the grooves on the side of the drawers and into the back panel of the drawer.
*Please note that the white side should be up for inside drawer.
C) Take the drawer front panel (Part 26 ) and insert 4 threaded composite bolts (Part 20 ). Use Phillips head screw-
driver to secure threaded connector pins.
30
30
27
28
29
25
20
26
June2013

7
D) Insert cams (Part 22 ) into the holes found on each side panel, making sure the holes of the T-nuts (Part 22 )
line up with the holes on the outer edge of the drawer sides.
E) Attach sides of drawers (Parts 27 & 28 ) to the drawer front (Part 26 ) by inserting threaded connection
pins (Part 20 ) into the holes on the outside edge of the drawer sides. *Please note that the grooves in each side must be
lined up with each other to allow the drawer bottom to be installed. To secure, tighten the T-nuts (Part 22 ) with Philipps
head screwdriver until tight.
F) Attach drawer handle (Part 12 ) to front drawer panel using 2 of 4x20mm bolts (Part 17 ).
Step 8
Attaching Pencil Ledge and Drawer Stopper
Attach pencil ledge (Part 23 ) to the front edge of table top, using two 4x12mm screws (Part 18 ).
After sliding drawer to table, attach drawer stopper (Part 24 ) to the left side of drawer, using 4x12mm screw (Part 18 )
and tighten it with Phillips head screwdriver.
22
18
18 24
20
20
17
22
26
12
27
28
23
June2013