Martin EC-10 User guide

EC Series LED Video Panels
and
EC Series Headers
Installation and Safety
Manual
TM
TM
EC-20EC-10

Dimensions
EC-10
All dimensions are in millimeters
485 100
770720
480
©2010-2011 Martin Professional™ A/S. Information subject to change without notice. Martin Professional A/S and all affiliated companies disclaim
liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or
reliance on the information contained in this manual. The Martin logo, the Martin name and all other trademarks in this document pertaining to services
or products by Martin Professional A/S or its affiliates and subsidiaries are trademarks owned or licensed by Martin Professional A/S or its affiliates or
subsidiaries.
P/N 35000238, Rev. E

3
EC-20
All dimensions are in millimeters

4 EC Series user manual
Safety Information
The following symbols are used to identify important safety information on the product and in this manual:
This product is for professional use only. It is not for household use.
This product presents risks of severe injury or death due to fire hazards, electric shock and falls.
Read this manual before installing, powering or servicing this product, follow the safety precautions listed
below and observe all warnings in this manual and printed on the product.
If you have questions about how to operate the EC Series system safely, please contact your Martin supplier
or call the Martin 24-hour service hotline on [phone], or in the USA on 1-888-tech-180.
PROTECTION FROM ELECTRIC SHOCK
• Connect the product to AC mains power within the range 200-240 V nominal at 50 or 60 Hz only.
• Disconnect the entire installation from power and ensure that power cannot be reconnected, even
accidentally, before carrying out any installation or maintenance work.
• Double-pole/neutral fusing is used. If the installation is not completely disconnected from power, parts
may remain live even if one of the two mains fuses has blown.
• Disconnect the product from power when not in use.
• Always ground (earth) the product electrically.
• Use only a source of power that complies with local building and electrical codes. Power distribution
circuits must be fitted with a current overload fuse or circuit breaker with a maximum rated current of 40 A
for European region and with a maximum rated current of 32 A for North American region, and
ground-fault (earth-fault) protection of high breaking capacity (≥1500 A).
• Connect the Header to power using only the cables supplied by Martin for this product.
• Protect power cables from water and rain.
• Connect the Header to power using only 32 amp-rated industrial Type B power plugs and socket outlets
that comply with IEC 60309 (or a comparable national standard) and provide an electrical connection to
ground (protective earth).
• External power switches or socket outlets used to supply Headers with power must be located near the
product and easily accessible so that the product can easily be disconnected from power.
• Do not connect any other device than EC Series panels to the power throughput connector in the base of
the product.
• Connect no more than sixteen EC Series panels in total to power in one chain using the power throughput
connectors in the base of the product.
WARNING!
Read the safety precautions in this section before
installing, powering, operating or servicing this
product.
WARNING!
Safety hazard.
Risk of severe
injury or death.
WARNING!
Refer to
manual before
installing,
powering or
servicing.
WARNING!
Hazardous
voltage. Risk of
lethal orsevere
electric shock.
WARNING!
Hotsurface.Do
not touch.
WARNING!
Fire hazard. WARNING! Emission
hazardous to
eyesight.

• Before using the product, check that all power distribution equipment and cables are in perfect condition
and rated for the current requirements of all connected devices.
• Do not use the product if the power cable or a power plug is in any way damaged, defective or showing
signs of overheating.
• Do not attempt to open any cover.
• Refer any service operation not described in this manual to a qualified technician.
• The supplied rubber caps must remain installed at all times on any unused power and data throughput
connectors. Keep all unused connector caps safely while panels are in use, and reinstall them as soon as
a video wall is disassembled.
PROTECTION FROM FIRE
• Provide a minimum clearance of 30 cm (11.8 in.) around the cover at the back of the panel base.
• Do not stick filters, masks or other materials directly onto LED modules.
• Do not modify the product in any way not described in this manual.
• Install only genuine Martin parts in or on the product unless an alternative is described in this manual.
• Do not operate the product if the ambient temperature (Ta) exceeds 40° C (104° F).
PROTECTION FROM INJURY
• Ensure that any structure used for support as well as all fastening and connecting hardware can hold at
least 10 times the weight of all supported devices and equipment.
• Do not suspend EC Series panels using any other method of attachment than those described in this
manual.
• Do not suspend more than sixteen EC Series panels from one Header.
• Create an installation by installing panels at the top and working downwards. Disassemble an installation
by removing panels at the bottom and working upwards.
• Check that all external covers and rigging hardware are securely fastened.
• Block access below the work area and work from a stable platform whenever installing, servicing or
moving the product.
• Do not look at lit LEDs from a distance of less than 40 cm (1 ft. 4 in.) without suitable protective eyewear.
• Do not view lit LEDs with optical instruments that may concentrate the light output.

6 EC Series user manual
Contents
Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Transporting EC Series panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Physical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
EC Series Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Suspension options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Creating an installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Dismantling an installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
AC power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Power connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Inrush current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Fuses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
P3™ communication link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Planning the P3 link. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Connecting the P3 link. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Monitoring status and testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Status indicator and test/reset button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Service and maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Installing new software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Replacing an LED block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Introduction 7
Introduction
This Installation and Safety Manual explains how to install, configure and maintain Martin™ EC™
Series video display panels. The Safety section contains very important warnings. The installation
section contains details of how to physically install panels and cables, connect panels to power and
prepare for connection to one of the Martin™ P3™ System Controllers and a video source.
For information about installing and using a P3 System Controller, see the user documentation
supplied with the Controller.
All EC Series and P3 Controller user documentation is also available for download free of charge
from the Product Support area at www.martin.com
Thank you for selecting a product from the Martin™ EC™ Series of modular LED-based video display
panels from Martin™. This product features:
• 10 mm (0.4 inch) pixel pitch and 48 x 72 pixels per panel image resolution on EC-10 panels
• 20 mm (0.79 inch) pixel pitch and 24 x 36 pixels per panel image resolution on EC-20 panels
• Rich RGB with color resolution of 16 bits per color
• Silent convection cooling
• Cable-free panel interconnection (integral power and P3 data connectors)
• Auto-sensing 200 - 240 VAC nominal switch mode power supply
For the latest firmware updates, documentation, and other information about this and all Martin
Professional™ products, please visit the Martin website at http://www.martin.com
Comments or suggestions regarding this document may be e-mailed to [e-mail] or posted to:
Technical Documentation, Martin Professional A/S, Olof Palmes Allé 18, DK-8200 Aarhus N, Denmark.
WARNING! Read “Safety Information” on page 4 before installing, powering, operating or servicing
the EC Series.
Like all LED video panels, an EC Series panel is an ITE Class A product. In a domestic environment this
product may cause radio interference, in which case the user may be required to take appropriate
measures.
Unpacking
Panels and panel flightcases
EC Series panels are ordered in multiples of a single item and supplied in flightcases. Panels and
flightcases must be ordered separately. Each flightcase has space for up to 8 panels.
The Flightcase, 8 x EC Series video panels (P/N 91515008) contains:
• Up to 8 EC Series panels (must be ordered as separate items)
• EC Series Installation & Safety Guide (P/N 35000238)
No cables are supplied in the flightcase because panels plug into each other, but there is space for storing
cables, curving hardware, etc.
Headers and Header flightcases
The EC Series Single Header in a cardboard box (P/N 90354240) contains:
• 1 x EC Series Header (P/N 90354220) with hard-wired power cable and eyebolt (installed)
• 1 x 5.0 m (16.4 ft.) Ethernet patch cable with IP67-rated RJ-45 connectors on both ends
• 1 x EC Series Header Installation & Safety Guide
The EC Series Double Header (P/N 90354250) is supplied as one assembled unit in a separately ordered
flightcase. It contains:
• 2 x EC Series Headers (P/N 90354220), each with hard-wired power cable and eyebolt (installed)
• 1 x EC Series Header Connection Bracket two panels wide (installed)
• 2 x EC Series Bracket Joining Plate

8 EC Series user manual
• 20 x bolt M12x20
• 2 x 5.0 m (16.4 ft.) Ethernet patch cables with IP67-rated RJ-45 connectors on both ends
• 1 x EC Series Header Installation & Safety Guide
The Flightcase for 1 x EC Series Double Header (P/N 91515006) must be ordered separately at the same
time as you order headers and offers quality protection for two Single Headers or one Double Header plus
all accessories.
The EC Series Triple Header (P/N 90354260) is supplied as one assembled unit in a separately ordered
flightcase. It contains:
• 3 x EC Series Headers (P/N 90354220), each with hard-wired power cable and eyebolt (installed)
• 1 x EC Series Header Connection Bracket three panels wide (installed)
• 2 x EC Series Bracket Joining Plate
• 22 x bolt M12x20
• 3 x 5.0 m (16.4 ft.) Ethernet patch cables with IP67-rated RJ-45 connectors on both ends
• 1 x EC Series Header Installation & Safety Guide
The Flightcase for 1 x EC Series Triple Header (P/N 91515007) must be ordered separately at the same
time as you order headers and offers quality protection for three Single Headers or one Triple Header plus
all accessories.
Curving Kit
EC Series Curving Kits (P/N 90354270) are supplied in a cardboard box. Components can be stored in an
EC Series 8-unit Flightcase. Each Kit contains:
• 50 x EC Series Curving Plate Locking Thumbwheels
• 50 x locknuts for thumbwheels
• 25 x EC Series Curving Plates (‘Bananas’)
• 1 x EC Series Curving Kit Installation & Safety Guide
Using for the first time
Before applying power to the panel:
• Carefully review “Safety Information” on page 4.
• Check that the local AC power voltage is within the ranges listed on the product’s serial number label and
in “AC power” on page 18.
• To supply the panel with power, use an EC series Header via the Header’s power cable tail.
Transporting EC Series panels
Important! To ensure that EC Series panels can withstand
the shocks that normally occur during transport,
they must be packed in a Martin EC Series
flightcase (see Figure 1) following the
instructions in the flightcase. Damage caused to
panels that are incorrectly packed or exposed to
abnormal shocks is not covered by the product
warranty.
Figure 1: EC Series flightcase

Physical installation 9
Physical installation
WARNING! Read “Safety Information” on page 4 before installing the EC Series.
WARNING! The safety and suitability of lifting equipment, installation location, anchoring method,
mounting hardware, suspension structures and electrical installation is the responsibility of the
installer. All local safety regulations and legal requirements must be observed when installing and
connecting the EC Series panels.
WARNING! Installation must be carried out by qualified professionals only. Contact your Martin
supplier for assistance if you have any questions about how to install this product safely.
WARNING! A maximum of sixteen EC Series panels may be suspended from one EC Series Header.
EC Series video panels are intended for suspension in vertical columns a maximum of sixteen panels high.
An unlimited number of correctly supported columns of panels may be installed horizontally alongside each
other. There is provision for both flat and curved video wall configurations.
It is possible to mix and interconnect EC-10 and EC-20 panels in an installation. The P3 System Controller
will recognize the different panel types.
The illustrations in this chapter show EC-20 panels, but procedures are identical for EC-10 panels.
EC Series Headers
EC Series video panels must be suspended in columns from EC Series Headers. Each Header has inputs
for power and P3 video data, and relays power and data to the panels suspended below it via integral
connectors.
A - Header power input cable
Used to supply power to the Header and attached EC
Series panels. Hard-wired via an IP67-rated cable
gland.
WARNING! A maximum of sixteen EC Series panels
in total may be connected to power in one chain
that draws power through one EC Series Header.
B - Eyebolt (supplied)
Can be used to support a Header if two or more
Headers are connected horizontally using Header
Connection Brackets. This eyebolt has a nominal
weight capacity of 800 kg.
C - Rigging clamps (not supplied)
Can be used to attach a Header to a truss Eor similar
supporting structure.
D - Header P3 data input cable
Used for bi-directional P3 system communication.
Accepts an Amphenol IP67-rated Ethernet cable
connector (or a standard Ethernet connector for indoor
use only).
E - Truss (not supplied)
Figure 2: EC Series Header

10 EC Series user manual
Suspension options
Various suspension methods can be used for the EC
Series. If suspension points are provided as directed
in this user manual, columns of panels maximum 16
panels high can be installed side-by-side to form any
width display surface.
The suspension options are:
1. Single columns of panels suspended from a Martin
Single Header using two rigging clamps per
column from a truss.
2. Single columns of panels suspended from a Martin
Single Header using two eyebolts per column from
steel cables, chains or hoists.
3. Groups of 2 or 3 columns of panels suspended
from a Martin Double or Triple Header using
minimum two eyebolts per Header from steel
cables, chains or hoists (i.e. minimum two eyebolts
and two suspension points per 2 or 3 columns of
panels).
4. Groups of any number of columns of panels
fastened into two or more Martin Double or Triple
Headers that are fastened to each other
horizontally using the Bracket Joining Plates
supplied with the Double or Triple Headers. In this
configuration, columns of panels can be
suspended using a minimum of one eyebolt per
Double or Triple Header from steel cables, chains
or hoists (i.e. minimum one eyebolt and one
suspension point per 2 or 3 columns of panels).
Creating an installation
WARNING!Read “Safety Information” on page 4 carefully before installing an EC Series system.
Before suspending panels
Before suspending a wall of EC Series panels by any of the methods listed above:
1. Check that the cables, chains, hoist, rigging points or other supporting structure can bear at least 10
times the total weight (panels, clamps, cables, auxiliary equipment, etc.) that they will have to support.
2. Check that supporting structures will not flex under the weight of the panels. Hanging panels from a
structure that is not straight will place a strain on panels and attachment hardware. Damage caused to
Headers or panels by mechanical stress is not covered by the product warranty.
3. Check that Headers are isolated from power and that power cannot be applied accidentally.
4. Block access under the work area.
5. Remove the supplied rubber connector caps (see Figure 4) and store them safely for re-use.
6. Note that each Header is supplied with one large eyebolt (Bin Figure 2) installed in the center of the top
of the Header. Headers also have provision for fastening M12 rigging clamps or eyebolts (not supplied)
near their outer ends.
Figure 3: Vertical installation limit
Maximum
sixteen (16)
panels high
Figure 4: Connector cap

Physical installation 11
7. Note that Headers have a male cone at one end and a female cone at the other end. Engaging male and
female cones will ensure correct side-to-side alignment of the Headers.
8. Similarly, note that EC Series video panels have cones for correct side-to-side alignment.
9. Check that safety cables are approved by an official body such as TÜV as a safety attachment for the
weight of all the equipment they secure.
Method 1: Suspending single
columns of panels from a truss
If suspending single independent columns of
panels one panel wide from a truss, see Figure
5:
1. See Figure 5. Obtain rigging clamps Cthat
are approved for the total weight they will
support. Fasten two clamps securely to each
Header using M12 fasteners that are
approved for the total weight they will
support.
2. Use the rigging clamps to fasten the Header
to the truss.
3. Loop an approved safety cable around the
truss and through the central eyebolt B.
4. Add panels as described in “Suspending EC
Series panels from Headers and other
panels”on page 12.
Method 2: Suspending single
columns of panels from steel cables,
chains or a hoist
If suspending single independent columns of
panels one panel wide from steel cables, chains
or a hoist:
1. See Figure 6. Obtain M12 threaded eyebolts
F(not supplied) that are approved as a
suspension point for the total weight they will
have to support. Fasten two eyebolts
securely into the threaded holes in each
Header as illustrated and use these as
suspension points for the Header.
2. Obtain a safety cable that is approved for the
total weight it will secure. Loop it through the
central eyebolt Bof each Header and use it
to attach the Header to a suitable support
that can hold ten times the static weight that
the safety cable secures.
3. Add panels as described in “Suspending EC
Series panels from Headers and other panels”on page 12.
Figure 5: Rigging clamps
C
BC
Figure 6: Additional eyebolts
B
FF

12 EC Series user manual
Method 3: Suspending groups of columns 2 or 3 panels wide
WARNING!Use minimum two eyebolts and minimum two suspension points per Header when
suspending one independent group 2 or 3 panels wide.
Martin Double and Triple Headers are supplied
in flightcases with Header Connection Brackets
installed (see Figure 7).
If using Martin EC Series Double or Triple
Headers to suspend independent groups of
columns 2 or 3 panels wide from steel cables,
chains or a hoist:
1. Check that the Header Connection Bracket
is firmly fastened to the Headers using the
M12 bolts supplied. Do not use any other
bolts than those supplied by Martin for this
purpose.
2. Attach a steel cable, chain or hoist that is
certified for the weight it will support to each
of the two eyebolts in the tops of Double
Headers or the two outer eyebolts in Triple
Headers, and use these to suspend the
group.
3. Add panels as described in “Suspending
EC Series panels from Headers and other
panels” on page 13.
Method 4: Suspending groups of columns 4 or more panels wide
WARNING! Use minimum one eyebolt and minimum one suspension point per Header if two or more
Double or Triple Headers are fastened together side-by-side in a group four or more panels wide.
If using Martin EC Series Double or
Triple Headers fastened together with
Joining Plates to suspend groups four
or more panels wide from steel cables,
chains or a hoist:
1. See Figure 8. Fasten Double or
Triple Header to each other using
two Joining Plates, one on the top
and one on the front surfaces of the
Headers, securing each plate with
eight of the 8 mm Allen M12 bolts
supplied with each Header (i.e.
sixteen bolts in total). Do not use
any other bolts than the ones
supplied by Martin for this purpose.
2. Attach a steel cable, chain or hoist
that is approved for the weight it will
support to at least one panel
eyebolt per Double or Triple
Header, and use these to suspend
the group of panels.
3. Add panels as described in
“SuspendingECSeries panelsfrom
Headers and other panels” on page
13.
Figure 7: Header Connection Bracket (Double
Header illustrated)
8
mm
Figure 8: Joining Plates for Header Connection Brackets

Physical installation 13
Suspending EC Series panels from Headers and other panels
The procedure for fastening an EC Series video panel to an EC Series Header or another EC Series panel
above it is the same:
1. Remove all rubber connector covers and store them safely for re-use.
2. Check that the locking handles Aare in the fully open position as shown in Figure 9.
3. See Figure 10. Lift the panel you are installing up to the Header or panel above so that the power and
data connector Band guide posts Cengage and the locking hooks in the panel touch the locking posts
Din the Header or panel above.
Figure 9: Locking handles before installation (cutaway view)
A
A
Figure 10: Hooks contact locking posts (cutaway view)
D
CC
B
D

14 EC Series user manual
4. See Figure 11. Continue lifting the panel so that its spring-loaded locking hooks are pushed open by the
locking posts Din the Header or panel above.
5. See Figure 12. Lift the panel until you hear both locking hooks click as they lock around the locking posts
Din the Header or panel above. Pull the panel back down to fully engage the hooks around the locking
posts D.
Figure 11: Hooks open around locking posts (cutaway view)
D
D
Figure 12: Hooks close around locking posts (cutaway view)
DD

Physical installation 15
6. Then turn both locking handles Afirmly down and in towards the center of the panel to lock the hooks in
position around the locking posts D.
7. Before adding panels, remove the rubber connector cover from the bottom of the panel you have just
installed and store it safely for re-use.
8. Continue hanging panels, removing rubber connector covers, inserting connectors and fastening the top
of each panel to the bottom of the panel above as shown in Figure 9. Up to a maximum of sixteen panels
in total may be suspended from one Header.
9. Check that the panel interconnection socket on the bottom of the lowest panel of each column is covered
by its rubber connector cap.
10.When taking down the installation, isolate from power and remove panels one at a time, starting at the
bottom and working upwards. Reinstall all rubber connector caps.
Side-to-side attachment
Panels can be attached side-to-side in a flat or curved wall to eliminate any gaps in the video display.
Side-by-side attachment in a flat wall
WARNING! Do not use side-by-side attachments to support
weight. Use only the vertical attachments for
weight bearing.
1. Check that the weight of both panels is
supported vertically.
2. See Figure 14. When two panels are alongside
each other, rotate both the two side-to-side
locking handles Bon one panel fully so that the
two side-to-side locking hooks Cengage in their
posts in the other panel and lock the panels
together.
Figure 13: Close locking handles to lock hooks round locking posts (cutaway view)
D
D
A
A
Figure 14: Horizontal locking in a flat-screen
array

16 EC Series user manual
Side-to-side attachment in a curved wall
EC Series Headers and panels can also be attached
horizontally to form a curved wall using the optional EC
Series Curving Kit (P/N 90354270).
• EC-10 panels can be installed in a concave curve with
panels angled at up to 15° to each other.
• EC-20 panels can be installed in a concave or convex
curve with panels angled at up to 20° to each other.
To install panels in a curved configuration:
1. See Figure 15. Unscrew the 2.5 mm Allen bolts
shown and remove the straight side-to-side
alignment cones Band washers Aclose to the top
and to the bottom of one side of each panel. Store all
components for possible re-use.
2. Remove the similar alignment cones from the
Headers.
3. Suspend the panels vertically as described earlier.
4. See Figure 16. Install the thumbwheels Asupplied in the Kit on the top and bottom profiles of each
panel, using the supplied locknuts to secure them in place so that they will not drop out of the panel if
loosened too much.
5. Insert two curved plates (or ‘bananas’)
Bsupplied in the Kit in their slots on the
top and bottom profiles. Once the
correct angle is obtained, lock the
columns by tightening thumbwheels A.
6. Install curving plates using the same
method in the slots in the bottom profile
of the Headers.
7. When the installation is disassembled,
the thumbwheels Acan be tightened
and left in position but remove the
‘bananas’ Band store them safely in the
flightcase for possible re-use.
8. Reinstall the alignment cones (see
Figure 14) on the sides of panels and
Headers before installing panels in a flat
wall.
Figure 15: Removing side-to-side
alignment cones
Figure 16: Locking panel angles in a curved array

Physical installation 17
Example installation
The example below shows a display screen seven EC Series panels wide and four panels high. EC-20
panels are shown in the illustration but the use of suspension points and Headers is identical for EC-10
panels.
Required items
• 28 x EC Series Panels
• 1 x EC Series Triple Header
• 2 x EC Series Double Headers
Configuration
See Figure 17. The
Triple Header is used in
the center of the wall,
and the two Double
Headers are attached
to each side of the
Triple Header using the
supplied Bracket
Joining Plates.
The wall must be
suspended using
minimum one eyebolt
per Single, Double or
Triple Header.
Dismantling an installation
When tearing down an installation, remove single panels starting at the bottom of the column and working
upwards. Reinstall all rubber connector caps and any straight side-to-side alignment cones you removed in
a curved installation (see Figure 15).
Figure 17: EC Series installation 7 panels wide
Suspension point
Suspension point
Suspension point

18 EC Series user manual
AC power
WARNING! The safety of the installation is the responsibility of the installer. Read “Safety
Information” on page 4 before creating an installation or connecting an EC Series panel to AC mains
power. Disconnect the entire installation from power before carrying out installation work.
WARNING! Connect to 200-240 VAC, 50/60 Hz mains power only.
WARNING! A maximum of sixteen EC Series panels in total may be interconnected using power
input and throughput connectors to form one chain that draws power via the first panel’s input
connector. If you do not respect these limits you will overload cables and components and create a
serious safety hazard. If you reach the maximum permitted number of interconnected panels in one
chain and want to supply more panels with power, you must create a new chain that draws power
from a separate power outlet.
WARNING! For protection from electric shock, the panel must be grounded (earthed). Power
distribution circuits must be fitted with a current overload fuse or circuit breaker with a maximum
rated current of 40A for European region and with a maximum rated current of 32A for North
American region) and ground-fault (earth-fault) protection of high breaking capacity (
≥ 1500 A).
WARNING! EC Series panels do not have a power on/off switch. They are powered on as soon as
mains power is applied to the power input connector and remain powered on until mains power is
shut down at source or disconnected. The external power switch or power outlet socket must be
located near the panels and easily accessible so that power to the panels can easily be shut down or
disconnected if necessary.
WARNING! Two-pole/neutral fusing.
WARNING! The supplied rubber caps must remain installed at all times on any unused power and
data throughput connectors. Keep unused caps safely for re-installation as soon as a video wall is
disassembled.
WARNING! Protect the power cables on the headers from water and rain.
Important! Connect the panels in the installation and the P3 System Controller to AC mains power at
the same outlet point in the power distribution circuit, or you may experience ground/earth loop
problems or create differences in potential that can damage devices. Damage caused by differences
in potential if devices are incorrectly connected to power is not covered by the product warranty.
Voltage range
EC Series panels feature an auto-sensing switch-mode power supply that accepts 200-240 V nominal AC
mains power at 50 or 60 Hz. Connect the panel to AC mains power that is within this voltage range only.
The EC Series can be supplied with AC mains power by connecting to one of the following three-wire
systems:
• a single-phase 200-240 V system (live, neutral, ground/earth), or
• two phases of a 3-phase delta or split-phase mid-point neutral system (phase, phase, ground/earth) to
obtain 200-240 V
Power figures are given under “Electrical” on page 28. Allow a sensible safety margin when calculating the
current headroom required on AC mains power distribution circuits for an EC Series installation.
Power connections
Power input
The EC Series Header is supplied with a 1 m (3 ft. 3 in.) hard-wired power input cable (see A in Figure 2 on
page 9). Protect this cable from rain. If necessary, lengthen with an appropriate cable according to local
building and electrical codes.
Power is relayed from a Header to a panel via the output socket: this is the same type of socket as the
throughput socket of a panel.

AC power 19
Panel interconnection
Power input and throughput connectors on EC Series panels are integral and engage automatically when
panels are installed in columns (see Figure 10 on page 13).
Power is supplied to columns of panels via the Header power input cable (see A in Figure 2 on page 9).
Power is relayed from the Header to the first EC Series panel and then from one panel to the next via power
throughput connectors (see A, Band C in Figure 18) and input connectors (see E, Gand H in Figure 18).
Do not power panels on or off by inserting or removing live power connectors or plugs, as this will cause
arcing at the connector contacts that may damage devices and connectors.
Power plugs and power outlet sockets
A power plug can be installed on the Header’s power input cable to make it easier to connect panels to AC
mains power outlets. Install an industrial grounding-type (earthed) 3-prong type B plug (see Figure 19) that
complies with IEC 60309 or a comparable national standard and is rated 240 V, 32 A minimum. For outdoor
or humid location use, the plug must also be IP67-rated. For indoor use, the plug may be IP44-rated.
Use corresponding power outlet sockets. Follow the plug and socket manufacturer’s instructions and all
locally applicable laws and electrical safety codes.
When installing a power plug on the Header’s power input cable for connection to a single-phase system at
200 - 240 VAC, 50/60 Hz:
• Connect the green/yellow ground (earth) conductor to the terminal marked or for connection to
ground (earth)
• Connect the blue conductor to the terminal marked Nfor connection to neutral
• Connect the brown conductor to the terminal marked Lfor connection to live
When installing a plug on the Header’s power input cable for connection to two phases of a 3-phase delta or
split-phase mid-point neutral system to obtain 200-240 VAC, 50/60 Hz:
• Connect the green/yellow ground (earth) conductor to the terminal marked or for connection to
ground (earth).
• Connect the blue conductor to the terminal marked N or Phase 1 or L1 for connection to one of the three
phases in the system
Figure 18: Power and data connectors
Power/data
throughput connectors
Power/data
input connectors
Figure 19: Industrial 32 A, 240 V IEC 60309 type B power plugs
IP67-ratedIP44-rated

20 EC Series user manual
• Connect the brown conductor to the terminal marked Lor Phase 2 or L2 for connection to another of the
three phases in the system
Table 1 gives details of standard wiring color codes and common pin identification symbols. If you have any
doubts about proper installation, consult a qualified electrician.
Inrush current
Inrush current peaks are unlikely to occur at exactly the same time in multiple panel installations and only
have a duration of a few microseconds, but bear in mind that inrush current when powering on may cause
unintentional tripping of circuit-breakers, especially if these have low resistance to momentary current
peaks.
Fuses
WARNING! Fuses are not user-replaceable and must be replaced by Martin or its authorized service
agents.
WARNING! Double pole / neutral fusing.
Each EC Series panel is protected by two 3.15 amp slow-blow mains fuses. The breaking capacity is 1500
A @ 250 V. Fuses are not user-replaceable. Contact Martin for service if you suspect that a fuse has blown.
Wire color (EU) Wire color (US) Pin (single-phase
system) Pin (3-phase system) Symbol
blue white neutral phase 1 N
brown black live phase 2 L
yellow/green green ground (earth) ground (earth) or
Table 1: Wire colors and pin identification