Master WIND DUO Manual

Dear Customer, thank you for purchasing a MASTER product.
Here you will find important information regarding the methods of use and the safety of installation.
is a wind safety device, with high voltage controls, for awnings, screens or similars. This device
rolls up the awning when the wind speed exceeds the setting threshold. It controls 2 motors with mechanical limit switch.
Comply with the following information
and keep for future reference.
FOR ACORRECT INSTALLATION, IT IS RECOMMENDED TO READ THIS INSTRUCTION GUIDE.
The producer cannot be consider responsible for any damages due to improper, wrong or unreasonable use.
WIND DUO
WARNINGS
1. Technical and general features (related to 20°C working temperature)
Power Supply :
Contacts Capacity :
Dimensions :
Wind Threshold :
230 Vac 50/60 Hz
2x10 A@250 Vac
100 x 100 x 60 mm
from 7 to 40 Km/h
01.
02.
03. .
04.
05. .
06.
07.
08.
09.
10.
11.
12.
13.
14.
15.
16.
17.
.
.
.
Manual controls with high voltage, be careful.
.
.
.
.
Strictly a .
.
.
The device must be installed by technical qualified staff so as to comply with the laws in force in your locality
Check that the package is intact and it has not suffered damage in transit
This device is subject by dangerous electric voltage.
Always connect the ground wire (yellow/green)
The installer is forced to arrange a section device on the system (with 3 mm minimum opening contacts)
Do not change, open or replace parts without manufacturer’s permission
For your safety, it is forbidden to work close to the roller tube with motor supplied.
In case of malfunctioning do not keep on trying on control and warn the technician.
Operate on the device with caution, using suitable tools.
Check that the power supply line does not depend on circuit for lighting.
The device has not a section device, the technician will take care to provide it into the system
Be sure that sensor has been installed on the correct position and well exposed to the wind and that there are no obstacles to the blades rotation
djusting the sensor with blades turned upside
Using sensors produced by the same manufacturer, or the warranty will be cancelled
The producer cannot be consider responsible for any damages due to improper, wrong or unreasonable use
Make connections without power supply
Adjust the motor limit switch before connecting it to the device
2. . Warnings on installation safety
WIND DUO
Instruction guide : Wind control for 2 motors
The device is proveded by two manual controls that can be permanent or momentary.Through this controls it is possible to move two awnings, manually or separately. Manual controls will be
disabled in wind alarm condition.
3. Manual control
Expired
At the end of the product cycle, dispose as provide by local regulation, or deliver again to the retailer when purchasing a new one. This product could contain polluting substance for the
environment and dangerous for health, if expired in a wrong way.
WIND DUO rev.02 dated 30.08.12
Sensors supported :
Protection Degree :
Protective Fuse:
sensor X15C
Ip55
5x20 fast 6,3 Amp
Working temperature : from -20°C to +55°C
It closes the awning when the wind speed exceeds the set threshold for longer than 3 seconds
It exits the wind alarm mode when about 8 minutes have elapsed since the last gust above the threshold. While in wind alarm mode, the manual controls are disabled.
When the set wind threshold is exceeded, the red led switches on. If this condition continues for at least 3 seconds, the device goes into wind alarm mode and the red led flashes for the whole wind
alarm time.
Once the device connected and wind alarm simulated (bring the awning to middle position and rotate the sensor blades) it can be possible to exit from alarm condition without waiting 8 minutes.
Hold
How to adjust wind threshold :
Wind presence signal :
Forced exit from wind alarm mode :
Rotate the trimmer on the device. Threshold is adjustable from 7 Km/h (trimmer completed rotate on the left) to 40 Km/h (trimmer completed rotate on the right).
The Factory sets up the Wind threshold at about 15 Km/h.
key RESET since led (flashing during the alarm) switches off(about 5 seconds).
4. Wind control
5. Fixing system
connection cables
X
connection cables
X
X
WRONG FIXING
RIGHT FIXING
R
awning 1
awning2
awning 1
awning 2
WIRED

All the products and the specific technicals contained in this document are subjects to variations without any warning.
MASTER declares that the device meets the principal requirement and the other regulations of the directive 1999/5/CE.
The declaration of conformity of the above products is available on the web site section «Conformity products».http://www.mastermotion.eu/it-IT/download,
6. Device scheme
L
0
N
AN
CP
7
Km/h
40
Km/h
-+
WIND THRESHOLD
ADJUSTING TRIMMER
KEY RESET
IDENTIFICATION
LABEL
PROTECTIVE
FUSE
L
0
N
AN
CP
-+
common
motors
ground
contact
M1
POWER SUPPLY
L
N
Wind sensor
mod. X15C
Manual
Control 1
Manual
Control 2
IN ORDER TO CHECK THAT CONNECTIONS HAVE BEEN DONE AS THE
SCHEME, BRING THE AWNING IN INTERMEDIATE POSITION AND ROTATE
THE SENSOR BLADES SINCE WINDALARM SETS OFF.
THE AWNING MUST MOVE UPWARD. IF THE AWNING MOVES DOWNWARD
REVERSE THE OPERATION WIRES OF MOTOR OR MOTORS.
IT IS POSSIBLE TO EXIT FROM WIND ALARM WITHOUT WAITING 8
MINUTES, KEEP HOLD KEY «RESET»SINCE RED LED SWITCH ES OFF.
CHECK SYSTEM
required
7. Electric Connection Scheme
WIND ALARM LED SIGNALLING
P
P
M2
WIND DUO rev.02 dated 30.08.12