MasterChef 85-3129-6 Propane User manual

SELECT 5-BURNER
PROPANE BARBECUE
Assembly Manual
85-3129-6 (G55105) Propane
1 YEAR LIMITED WARRANTY
ANSI Z21.58-2015 / CSA 1.6-2015
ANSI Z21.58-2015 / CSA 1.6-2015 ANSI Z21.58-2015 / CSA 1.6-2015
ANSI Z21.58-2015 / CSA 1.6-2015
READ AND SAVE MANUAL FOR FUTURE REFERENCE.
Assemble your grill immediately.
Missing or damaged parts claims must be submitted within 30 days of purchase date.
For product inquiries, parts, warranty and troubleshooting support,
please call 1-855-453-2150.

DANGER
1. If you smell Gas:
a. Shut o gas to the appliance.
b. Extinguish any open ame.
c. Open lid.
d. If odor continues, keep away from
the appliance and immediately
call your gas supplier or your
re department.
2. Requires two people to complete the
assembly process.
3. Beware of sharp edges.
WARNING
Failure to follow all of the Manufacturer’s
instructions could result in hazardous res,
explosions, property damage, or serious
personal injury or even death.
Follow all leak check procedures carefully
prior to operation of barbecue, even if grill
was dealer assembled. Do not try to light
this barbecue without reading the Lighting
Instructions section of this manual.
THIS MANUAL MUST REMAIN WITH THE PRODUCT AT ALL TIMES
CAUTION
Read and follow all safety statements,
assembly instructions, use and care
directions before attempting to assemble
and cook.
WARNING
1. Do not store or use gasoline or other
ammable liquids or vapours in the
vicinity of this or any other appliance.
2. An LP cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
WARNING
IN DIRECT SUN, AND IN OPERATION,
YOUR BBQ’S STAINLESS STEEL AND
PAINTED STEEL PARTS CAN BECOME
VERY HOT.
CAUTION
Sharp edges. Wear gloves when assembling
your grill.
THIS BARBECUE IS FOR OUTDOOR USE ONLY.
CONTACT CALL CENTRE IF ANY PARTS ARE MISSING.
1-855-453-2150
INSTALLER OR ASSEMBLER/CONSUMER
This manual should be kept with the BBQ at
all times.
HEAVY ARTICLE NEEDS 2 TO LIFT
To ORDER non-warranty replacement parts or accessories, or to register your warranty,
please visit us on the web at
www.masterchefbbqs.com

1
HARDWARE PACK
1/4”-20UNC X13 Screw
X 20
ST4.2X8 Tapping Screw
X 14
Wheel Spacer
X 2
Control Knob
X 1
NO.10-24UNC Nut
X 3
NO.8-32UNC X10 Screw
X 2
1/4’’-20UNC Nut
X 8
Aluminum Washer
X 8
Hitch Pin
X 1
NO.10-24UNC X18 Screw
X 3
M4 Wing Nut
X 1
Wheel Washer
X 1
Bezel, Control Knob
X 1
Venturi Clip, Side Burner
X 1
1 2 3
4 5 6
7
10
13
8
11
14
9
12
KEY # DESCRIPTION PART NUMBER QUANTITY
1 1/4”-20UNC X13 Screw 20120-13013-036 20
2 1/4”-20UNC Nut 31220-13000-036 8
3 ST4.2X8 Tapping Screw 24200-42008-136 14
4 Aluminum Washer G466-0042-9000 8
5 Wheel Spacer G650-0012-9091 2
6 Wheel Washer G650-0013-9091 1
7 Hitch Pin G306-0005-9088 1
8 Control Knob G312-B102-01 1
9 Bezel, Control Knob G430-0027-02 1
10 NO.10-24UNC X18 Screw 20124-10018-036 3
11 NO.10-24UNC Nut 31224-10000-036 3
12 Venturi Clip, Side Burner G405-0019-9200 1
13 M4 Wing Nut 33301-04000-032 1
14 NO.8-32UNC X10 Screw 20132-08010-250 2
TOOLS NEEDED FOR ASSEMBLY
• #2 Star-head screwdriver (long and short)
• ¼” Slotted screwdriver (long and short)
• Adjustable wrench
• Pliers
For correct hardware assembly, always position
the lock washer between the screw and the at
washer.
Caution:
Sheet metal can cause injury. Wear gloves when installing the grill.
Lock Washer
Flat Washer
Screw
BEFORE ASSEMBLING THIS BARBECUE, READ THE INSTRUCTIONS CAREFULLY.
Assemble the barbecue on a flat, clean surface. Grill is heavy. Two people are recommended
to complete assembly.

2
PARTS LIST PROPANE FOR 8531296 G55105
KEY # QUANTITY DESCRIPTION PART NO.
AA 1 Top Lid Assembly G551-6700-01
AB 1 Thermometer and Bezel G312-B201-01
AC 2 Lid Handle Brackets G352-0015-01
AD 1 Top Lid Handle G551-0001-01
AE 2 Lid Bumpers, Back G303-0038-01
AF 2 Lid Bumpers, Front G430-00B8-01
AG 2 Screws for Lid G430-0024-02
BA 1 Burner Box Assembly G551-0300-01
BB 5 Burner G432-B600-01
BC 1 Electrode Set, Main Burner G501-0010-01
BD 4 Burner Brace Assembly G551-0006-01
BE 5 Flame Tamer G432-0096-01
BF 3 Cooking Grate G551-0400-01
BG 1 Warming Rack G551-0005-01
CA 1 Control Panel G551-0013-01
CB 1 Manifold Assembly G551-5200-01
CC 1 Metal Hose, Side Burner G430-2403-01
CD 1 Side Burner Valve, LP G551-5201-01
CE 1 Regulator G311-0503-01
CF/#9 6 Bezel, Control Knob G430-0027-02
CG/#8 6 Control Knob G312-B102-01
CH1 1 Electronic Ignition Assembly G409-0021-A1
CH2 1 Electronic Ignition Button G409-0030-01
CI 1 Grease Cup Hook G305-0043-01
CJ 1 Grease Cup G430-0033-02
CK 1 Heat Shield G551-0003-01
DA 1 Cart Side Panel, Right G551-0900-01
DB 1 Cart Side Panel, Left G551-0800-01
DC 2 Back Brace G551-1000-01
DD 1 Upper Front Panel G551-0008-01
DE 1 Lower Front Panel G551-0009-01
DF 2 End Caps G430-0023-01
DG 2 Wheel G401-0058-01
DH 1 Wheel Axle G651-0027-01
DI 1 Match Holder G401-0079-01
DJ 3 Tank Exclusion G551-0011-01
DK 1 Gas Tank Support G551-0010-01
EA 1 Side Shelf Table, Right G451-0B00-01
EB 1 Side Shelf Fascia, Right G551-6901-01
EC 1 Side Shelf Table, Left G551-0600-01
ED 1 Side Shelf Fascia, Left G551-6801-01
EE 1 Side Burner Drip Pan G651-0038-01
EF 1 Side Burner G551-5500-01
EG 1 Electrode Set, Side Burner G430-0042-02
EH 1 Side Burner Grate G430-0053-01
EI 1 Side Burner Lid G430-0018-A1
F1 1 Hardware Pack G551-B005-01
F2 1 Assembly Instructions G551-M005-01
F3 1 Safe Use and Care Manual G551-M005-02

3
EXPLODED DIAGRAM PROPANE FOR 8531296 G55105
BF
BE
BA
CA
AG
AE
AF
AC
BG AB
AA
AD
CK
BC
CE
DG
DH
DA
DC
CF
EA
CI
CJ
EB
DF
DI
DD
DE
DB
BB
BD
CH2
CH1
EH
DK
DJ
EF
#9
#8
EC
EI
ED
CC
CB
EE
CD
CG
EG
HARDWARE
PACK
F1
F2 F3
ASSEMBLY
MANUAL
SAFETY
AND CARE
MANUAL

4
Note: Two people required for all assembly steps.
Assemble the Upper Front Panel (DD) and Lower
Front Panel (DE) to the the Left and Right Cart Side
Panels (DB and DA) as shown.
1
ASSEMBLY INSTRUCTIONS
YOU WILL NEED:
YOU WILL NEED:
1
3
X 8
X 8
Back View
Assemble the two Back Braces (DC) to the
Left and Right Cart Side Panels (DB and DA) as
shown.
2
DA DB
DA
DB
DD
DE
A
A
DC
B
Close Up
DC

5
Note: Turn Cart assembly upside down.
a. Place Wheel (DG) and Wheel Spacer (#5) onto
the Wheel Axle (DH). “Cone”side of wheel
should be against cart side panel. Figure B.
b. Insert Wheel Axle Assembly (DH) through
wheel axle hole in the front and rear of the Left
Cart Side Panel (DB), as shown.
c. To complete wheel assembly position the
Wheel Spacer (#5), Wheel (DG), Wheel Washer
(#6) and Hitch Pin (#7), onto Wheel Axle (DH)
as shown.
d. Insert End Caps (DF) into Right Cart Side Panel
(DA).
3
4
ASSEMBLY INSTRUCTIONS
876
YOU WILL NEED:
5
X 2
7
X 1
6
X 1
DG
5
56
7
DG
DH
A
DF
DB
Assemble the three Tank Exclusion Wires (DJ) to
the Lower Back Brace (DC) and the Front Panel
(DD and DE) as shown.
Back View
Close up - front view
Close up - back view
DE
DD
DJ
DJ
DJ
YOU WILL NEED:
10 11
X 3 X 3
DC
Close upClose up
C
B
57
6

6
Note: TWO PEOPLE required for this step.
Ensure that the regulator hose (CE) (Propane
models only) is hanging outside of cart.
a. Position the Lid and Burner Box Assembly
(A & B), onto the cart assembly (C).
b. Assemble the Burner Box Assembly (BA) to the
cart assembly (C) as shown in gure B.
YOU WILL NEED:
ASSEMBLY INSTRUCTIONS
1
X 4
A B
+
C
A
B
5
6
BA
DB
PROPANE MODEL ONLY.
Assemble the Gas Tank Support (DK) to Left Cart
Side Panel (DB).
Back View
Close up
DK
DA
DB
DB
DK

7
ASSEMBLY INSTRUCTIONS
7RIGHT SIDE SHELF ASSEMBLY
a. Insert the Right Side Shelf Assembly (EA and
EB) into the support brackets located on the
right side of the Burner Box Assembly (BA).
b. Ax the Right Side Shelf Table (EA) to the
Burner Box Assembly (BA) as shown in
gures B and C.
c. Ax the Right Side Shelf Fascia (EB) to the
Control Panel (CA).
Securely tighten all hardware.
YOU WILL NEED:
YOU WILL NEED:
YOU WILL NEED:
3
X 3
EA
BA
CA
EB
D
Front, right side view
Back View
View, under right side shelf
View, under right side shelf
EA
EB
BA
A
BA
B
A1
EA
EB
BA
C
B2
B2
14
X 4 X 4
A1
2
X 4
B2
A1

8
ASSEMBLY INSTRUCTIONS
8LEFT SIDE SHELF ASSEMBLY
a. Insert the Left Side Shelf Assembly (EC and ED)
into the support brackets located on the right
side of the Burner Box Assembly (BA).
b. Ax the Left Side Shelf Table (EC) to the Burner
Box Assembly (BA) as shown in gures B and C.
c. Ax the Left Side Shelf Fascia (ED) to the
Control Panel (CA).
Securely tighten all hardware.
YOU WILL NEED:
3
X 3
YOU WILL NEED:
YOU WILL NEED:
1
2
4
X 4
X 4
X 4
BA
C
B
D
A
BA
EC
EC
BA
ED
BA
View, under left side shelf
Back view
Front, left side view
View, under left side shelf
CA
EC
ED
ED
A1
A1
B2
B2
A1
B2

9
9a. Assemble the Control Knob Bezel (#9) to the
Left Side Shelf Fascia (ED) and the Side Burner
Valve (CD) as shown in gures A and B.
b. Position the Side Burner (EF) through the
opening in the Left Side Burner Drip Pan (EE).
c. Make sure that the Side Burner (EF) engages
the Side Burner Valve (CD) as shown in gure D.
ASSEMBLY INSTRUCTIONS
C
B
D
A
View, under left side shelf
Front view
Left side view
View, under left side shelf
EF
CD
ED
ED
ED
9
976
YOU WILL NEED:
9
X 1
14
X 2
CD
EE
EF
EC

10
ASSEMBLY INSTRUCTIONS
9
e. Use the Side Burner Venturi Clip (#12) to
connect the Side Burner (EF) to the Side Burner
Valve (CD) as shown in gure F.
f. Assemble the Side Burner Electrode Wire (EG)
to the underside of the Side Burner Electrode
(EF) as shown in gure G.
EF
EF
EF
EG
EE
CD
YOU WILL NEED:
YOU WILL NEED:
13
12
X 1
X 1
E
F
G
View, under left side shelf
View, under left side shelf
View, under left side shelf
d. Assemble the Side Burner (EF) to the Side
Burner Drip Pan (EE) as shown in gure E.
13
12

11
ASSEMBLY INSTRUCTIONS
a. Position the Side Burner Cooking Grate (EH)
onto the Side Burner Drip Pan (EE).
b. Assemble the Side Burner Control Knob (#8) to
the Side Burner Valve (CD).
10
EH
EE
A
B
YOU WILL NEED:
8
Place the Flame Tamer (BE) into the Burner Box
Assembly (BA).
A
BA
BE
Close up, front
Close up, back
BE
BE
B
C
11
X 1
8
CD

12
ASSEMBLY INSTRUCTIONS
13 To assemble the Warming Rack (BG), insert the
stationary wire into the holes on the sides of the
lid. Insert warming rack pivot legs into the holes
on the inside of the burner box assembly, as
shown.
12 Place the Cooking Grates (BF) into the Burner Box
Assembly (BA).
BF
BG
Stationary Wire
Pivot Legs
Close up
BA
BG

13
ASSEMBLY INSTRUCTIONS
14
CI
BA
CJ
Back view
Close up
CI
CJ
15 Electronic ignition battery not included.
Unscrew the electronic ignition button (CH2) and
insert one AA battery into the electronic ignition
battery compartment (CH1), with the positive
end facing outward.
CH1
CH2
+
-
Hang the Grease Cup Hook (CI) from the bottom
of the Burner Box (BA), and place Grease Cup (CJ)
into position.
CAUTION
Failure to assemble grease cup hook and grease
cup will cause hot grease to drip from the
bottom of the BBQ burner box, with the risk of
re, property damage, or personal injury.

14
ASSEMBLY INSTRUCTIONS
16
DK
CE
Position the 20 lb propane tank into the notches
located on the bottom of the Left Cart Side Panel
(DB). Position the Gas Tank Support (DK) onto
the tank collar. Attach the regulator coupling nut
(CE) to the propane tank valve.
ATTENTION
LP Cylinder is sold separately.
Use only LP tanks that are equipped with an
OPD (Overll protection device). Fill and leak
check before attaching to the BBQ hose and
regulator. See Safe Use and Care Manual, leak
test procedure for more information
CAUTION
Cylinder valve must face to the front of cart
once the tank is attached.
Failure to install cylinder correctly may allow
gas hose to be damaged in operation, resulting
in re.
WARNING
Always keep LP cylinder in upright position
during use, transport and storage.
WARNING
When assembling regulator onto LP cylinder,
ensure that the regulator is assembled below
the support bar, as shown.

• CAUTION!
• AVOID BURNS!
• DO NOT TOUCH WHEN BBQ IS IN USE!
• EXTREMELY HOT SURFACE!
* SHADED AREAS BECOME EXTREMELY HOT WHEN IN USE.
WARNING HOT SURFACES:
!
!
!

Trileaf Distributions Trifeuil
Toronto, Ontario M4S 2B8
Visit www.masterchefbbqs.com
to complete product registration.
Master Chef® Customer Service
1-855-453-2150