Matatakitoyo Torque Tools MTS-3002 User manual

1. Study this instruction before use.
2. Please wear gloves and goggles when working.
3. Always check for loose wires and cables on and around tester before beginning operation.
4. Keep tester and charger away from water, always store in a dry place and safe environment.
5. Over torque will cause tool damage and personal injury.
6. Never use additional accessories with this tester that were not included and are not from this manufacturer,
doing so could result in damage to the tester.
7. Always operate tester in a clean and organized work place.
8. This tester should always be kept clean, dry, and free from oil and grease.
9. This tester should be recalibrated a period of 1 years, or 5,000 cycles, whichever occurs first.
To contact with local vendor, an authorized repair center for supporting.
10. Always unplug tester before inspecting, cleaning, or performing maintenance on the tester.
BEFORE STARTING
Manual
WARNING
1 Years
5000 Times
- 1 -
OPERATION MANUAL
Torque Tester
MTS-3002
RSR-Series
Models covered

RSR Torque Transducer Paper Box Manual
RSR MAINTENCE AND STORAGE
RSR TORQUE TRANSDUCER SPECIFICATION
■ Accuracy : C.W. ± 1% / C.C.W. ± 1.5%
■ Temp. Range-Operating : +5℃ to +40℃
■ Temp. Range-Storage : -20℃ to +70℃
■ Directions : C.W., C.C.W.
■ Calibration : According to BS7882 method
RSR CONTENTS
RSR TECHNICAL SPECIFICATION
Drive End6 Pins Connector (To MTS-3002)
1. Clean this tool by wiping with a clean cloth after
operation and storage in a dry environment.
2. Do not dip any type of liquid in this tool.
This may damage the internal of this tool.
W
M
A
L
L1
L2
ITEM NO. Range L
RSR-500N
RSR-1000N
RSR-1500N
RSR-2000N
RSR-5000N
1.47
1.72
1.80
2.10
4.70
L2
93
93
93
93
110
W
80
80
80
80
110
153.6
166.0
167.0
172.0
180.0
25-500 Nm / 18-370 ft.lb
50-1000 Nm / 36-740 ft.lb
75-1500 Nm / 55-1106 ft.lb
100-2000 Nm / 73-1475 ft.lb
250-5000 Nm / 180-3687 ft.lb
KG
A
3/4”
3/4”
1”
1”
1-1/2”
M
21
27
27
32
46
TORQUE
3/4” 1-1/2” 1”
Unit : mm
- 2 -

MTS-3002 DISPLAY SPECIFICATIONS
MTS-3002 PARTS
■ Display : 5 Digits, 7 segment LED (update rate of 5 per second)
■ Temp. Range-Operating : +5℃ to +40℃
■ Temp. Range-Storage : -20℃ to +70℃
■ Sampling Rate : 333 SPS
■ Auto Reset Hold Time : 2 Seconds (Auto Reset Mode)
■ RS-232 Data out
■ N-m, Kg-m, FT-LB, IN-LB are interchangeable
■ Mode : Track, Auto Reset, Hold
MTS-3002 TECHNICAL SPECIFICATION
MTS-3002 FRONT PANEL
MTS-3002 BACK PANEL
1 2 3 4 5
Unit : mm
MTS-3002 Torque Display
DVD DISCSensor Cable RS-232 CableDC Adapter
HW
D
ITEM NO. D W H
MTS-3002 70140190 1.70
KG
- 3 -
1 Buzzer
2 Zero Key : Zero Transducer
3 Unit Key : Unit select
4 Mode Key : Mode select
5 Unit Indicator (N-M)
6 Unit Indicator (KG-M)
7 Unit Indicator (FT-LB)
8 Unit Indicator (IN-LB)
9 Mode Indicator (TRACK)
Mode Indicator (AUTO RESET)
Mode Indicator (HOLD)
Display
1 Power Switch
2 DC Input
3 RS-232
4 TRANSDUCER
5 Aux. Output (Reserved)
10
11
12
1
12
2 3 4
5
6
7
8
9
10
11

100 Nm
TRACK MODE
AUTO RESET MODE
HOLD MODE
TORQUE WRENCH SOFTWARE
E-mail:[email protected]om
www.matatakitoyo.com
Made in Taiwan
MATATAKITOYO TOOL CO., LTD.
No. 63, Ln. 493, Sec. 3, Zhongshan Rd., Tanzi Dist.,
Taichung City 42754, Taiwan
TEL : [phone]
Manufacturer
01
0
100 Nm
Please refer to TORQUE TESTER INSTRUCTION MANUAL
0
100 Nm
0
Time
Torsion
Torsion
Torsion
Delay time
2 Seconds
1 st peak value (Peak hold)
1 st peak value (Peak hold)
Infinite loop Press Zero button to Reset
Reset
Example for click type torque wrench with a single measurement
Example for click type torque wrench with a single measurement
Each test require release torque from 0
Each test require release torque from 0
Sep. 2020
Edition