Matrix G3 STRENGTH User manual

G3 STRENGTH
G3-S12 PECTORAL FLY
MATRIX FITNESS | 1600 LANDMARK DRIVE COTTAGE GROVE WI 53527 USA
To l l Free 866.693.4863 matrixfitness.com Fax [phone]
PART # 0000000000
REV. 1.1
ACTION FREQUENCY
Clean Upholstery Daily
Inspect Cables Daily
Clean Guide Rods Monthly
Inspect Hardware Monthly
Inspect Frame Bi-Annually
Clean Machine As Needed
Clean Grips As Needed
Lubricate Guide Rods As Needed
Upholstery & Grips should be cleaned with a non-ammonia based cleaner (like Simple Green) or a mild soap and water.
Guide rods should be lubricated with Teflon based lubricant. Apply the lubricant to a cotton cloth and then apply up and
down the guide rods.
MAINTENANCE CHECKLIST
PRODUCT SPECIFICATIONS
TECH SPECS
Overall dimensions 44”L X 60”W x 59”H (112 cm x 152 cm x 150 cm)
Weight 542 lbs (246 kg)
Shipping weight 582 lbs (264 kg)
WARRANTY (Valid in USA only)
Frame (not coatings) 10 years
Structural parts 10 years
Weight stacks 5 years
Pulleys 5 years
Pivot bearings 5 years
Any items not specified 3 years
Labor (excluding upholstery/cables/grips) 3 years
Upholstery/cables/grips/springs 1 year
IMPORTANT SAFETY INFORMATION
It is the sole responsibility of the purchaser of MATRIX Fitness Systems products to instruct all individuals, whether they
are the end user or supervising personnel on proper usage of the equipment.
It is recommended that all users of MATRIX Fitness Systems exercise equipment be informed of the following information
prior to its use.
PROPER USAGE
Do not use any equipment in any way other than designed or intended by the manufacturer. It is imperative that MATRIX
Fitness Systems equipment be used properly to avoid injury.
Keep hands and feet clear at all times from moving parts to avoid injury.
CHECK FOR DAMAGED PARTS
1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by
your country’s local MATRIX Fitness Systems dealer.
2. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain important information.
If unreadable or missing, contact your MATRIX Fitness Systems dealer for a replacement.
3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking or tipping over.
This must be performed by a licensed contractor.
4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping
your liability to a minimum. Equipment needs to be inspected at regular intervals.
5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so.
MATRIX Fitness Systems dealers will provide service and maintenance training at our corporate facility upon request.
WARNING: SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT. FOLLOW THESE PRECAUTIONS TO
AVOID INJURY!
1. Never allow children on freeweight or bench equipment. Teenagers must be supervised at all times while using
this equipment.
2. All warnings and instructions should be read and proper instruction obtained prior to use.
3. Cease exercise if you feel faint or dizzy. Obtain a medical exam before beginning an exercise program
4. Keep body, hair, clothing and fitness accessories free and clear of all moving parts.
5. Inspect the machine before use. DO NOT use machine if it appears damaged or inoperable.
6. This equipment should only be used in supervised areas where access and control are regulated by the owner.
S12_pec_fly_r1.1.indd 1 12/13/10 8:58 AM

G3-S12 PECTORAL FLY
UNPACKING G3-S12 PECTORAL FLY
Thank you for purchasing a MATRIX Fitness product. This machine is an EN957-1 and EN957-2 complaint Class S product. Your
MATRIX G3-S12 PECTORAL FLY is inspected before it is packaged. It is shipped in multiple pieces to facilitate the compact
packaging of the machine. Prior to assembly, confirm all the components by matching them with the exploded diagrams. Carefully
unpack the unit from this box and dispose of the packing materials in accordance with your local laws.
CAUTION
The weight of the G3-S12 PECTORAL FLY is 542 lbs. (246 kg) including the weight stack. To avoid injury to yourself and prevent
damage to the frame components, be sure to have proper assistance removing the frame pieces from this box. Please be sure to
install the equipment on a stable base, properly level the machine and leave at least two feet of clearence to enter and exit the
machine. Maximum user weight for this machine is 350 lbs. (159 kg).
INCLUDED TOOLS REQUIRED FOR ASSEMBLY
17MM Open-End Wrench
3MM L-Shaped Allen Wrench
4MM L-Shaped Allen Wrench
5MM L-Shaped Allen Wrench
6MM L-Shaped Allen Wrench
8MM L-Shaped Allen Wrench
10MM L-Shaped Allen Wrench
If any items are missing please contact your country’s local MATRIX dealer for assistance.
0mm 10 20 30 40 50 60 70 80 90 100 1
10 120 130 140 150 160
Step 1
Frame Detail
Qty
16
16
24
8
Flat Washer
Screw
Lock Washer
Screw
Arc Flat Washer
Item
G14
C43
D36
C42
Description
Arc-at Washer
Flat Washer(M10)
Lock Washer(M10)
Screw(M10X25L)
G14
C42
C43
D36
G14
Step 2
Input Detail
Screw(M10X60L)
Screw(M12X25L)
Lock Washer(M12)
Flat Washer(M12)
Nylon Nut(M10) 2
2
F26
C44
4
4
4
D26
D30
D27
Qty
Description
Item
F26
C44
D26
D27
D30
D26
D27
D30
Step 5
Belt Routing Detail
Qty
Lock Washer
Screw
Belt Fixer
Flat Washer
F16
F16
2
F25 F30F29
F20
4
4
2
4
Description
Item
Belt F16
F25
F29
F30
Belt Fixer
F20
Screw(M5)
Flat Washer(M5)
Lock Washer(M5)
Step 6
Accessory Detail
Upper Cover Detail
AB1
B43
B51
Q02
B18
Towel / Water
Bottle Holder
Upper Cover
Q07
Q07
Weight Shield
Q01
Q05
Rubber Tip Weight Shield Bolt
Rubber Shield Spacer
Q05
Q07
Item Description Qty
Q02 Upper Cover 3
B51 6
B18 Water Bottle Holder 1
Weight Shield
Q01 1
Internal Tooth Lock Washer
B43 6
6
6
Z50 2
Screw(M4X12L)
Z50
Screw(M8X18L)
B28
B 28 2
Allen Head Cap Screw
Step 3
Upholstery Detail QtyItem
G11 19
Description
Screw (M10X25L)
G11
G11
G11
Step 4
Weight Stack Detail
K05
K13
K07
B28
Guide Rod
Top Weight
Selector Pin
Screw
2K07 Rubber Stack Cushions
E-Clipper
L09
K13
B28
2
2
4
Description
Knurled Belt Securing Insert
Item
K05
Qty
1
Guide Sleeve
L14
L13
F29
L09L11K18
L11 2
F29
L14
L13 4
4
4
Knurled Belt Securing Insert
K18 2
Screw(M8X30L)
Flat Washer(M5)
Flat Washer(M8)
Screw(M8X20L)
Lock Washer(M8)
Lock Washer(M5)
Screw(M5X16L)
1010
10
25
190
280
295
235
265
250
220
205
145
160
175
115
130
70
100
85
55
40
S12_pec_fly_r1.1.indd 2 12/13/10 8:58 AM

G3 STRENGTH
G3-S13 CONVERGING CHEST PRESS
MATRIX FITNESS | 1600 LANDMARK DRIVE COTTAGE GROVE WI 53527 USA
To l l Free 866.693.4863 matrixfitness.com Fax [phone]
PART # 0000000000
REV. 1.1
ACTION FREQUENCY
Clean Upholstery Daily
Inspect Cables Daily
Clean Guide Rods Monthly
Inspect Hardware Monthly
Inspect Frame Bi-Annually
Clean Machine As Needed
Clean Grips As Needed
Lubricate Guide Rods As Needed
Upholstery & Grips should be cleaned with a non-ammonia based cleaner (like Simple Green) or a mild soap and water.
Guide rods should be lubricated with Teflon based lubricant. Apply the lubricant to a cotton cloth and then apply up and
down the guide rods.
MAINTENANCE CHECKLIST
PRODUCT SPECIFICATIONS
TECH SPECS
Overall dimensions 49”L X 55”W x 69”H (124.5 cm x 140 cm x 175 cm)
Weight 645 lbs (293 kg)
Shipping weight 668 lbs (303 kg)
WARRANTY (Valid in USA only)
Frame (not coatings) 10 years
Structural parts 10 years
Weight stacks 5 years
Pulleys 5 years
Pivot bearings 5 years
Any items not specified 3 years
Labor (excluding upholstery/cables/grips) 3 years
Upholstery/cables/grips/springs 1 year
IMPORTANT SAFETY INFORMATION
It is the sole responsibility of the purchaser of MATRIX Fitness Systems products to instruct all individuals, whether they
are the end user or supervising personnel on proper usage of the equipment.
It is recommended that all users of MATRIX Fitness Systems exercise equipment be informed of the following information
prior to its use.
PROPER USAGE
Do not use any equipment in any way other than designed or intended by the manufacturer. It is imperative that MATRIX
Fitness Systems equipment be used properly to avoid injury.
Keep hands and feet clear at all times from moving parts to avoid injury.
CHECK FOR DAMAGED PARTS
1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by
your country’s local MATRIX Fitness Systems dealer.
2. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain important information.
If unreadable or missing, contact your MATRIX Fitness Systems dealer for a replacement.
3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking or tipping over.
This must be performed by a licensed contractor.
4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping
your liability to a minimum. Equipment needs to be inspected at regular intervals.
5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so.
MATRIX Fitness Systems dealers will provide service and maintenance training at our corporate facility upon request.
WARNING: SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT. FOLLOW THESE PRECAUTIONS TO
AVOID INJURY!
1. Never allow children on freeweight or bench equipment. Teenagers must be supervised at all times while using
this equipment.
2. All warnings and instructions should be read and proper instruction obtained prior to use.
3. Cease exercise if you feel faint or dizzy. Obtain a medical exam before beginning an exercise program
4. Keep body, hair, clothing and fitness accessories free and clear of all moving parts.
5. Inspect the machine before use. DO NOT use machine if it appears damaged or inoperable.
6. This equipment should only be used in supervised areas where access and control are regulated by the owner.
S13_conv_chest_press_r1.1.indd 1 12/13/10 8:55 AM

G3-S13 CONVERGING CHEST PRESS
UNPACKING G3-S13 CONVERGING CHEST PRESS
Thank you for purchasing a MATRIX Fitness product. This machine is an EN957-1 and EN957-2 complaint Class S product. Your
MATRIX G3-S13 CONVERGING CHEST PRESS is inspected before it is packaged. It is shipped in multiple pieces to facilitate the
compact packaging of the machine. Prior to assembly, confirm all the components by matching them with the exploded diagrams.
Carefully unpack the unit from this box and dispose of the packing materials in accordance with your local laws.
CAUTION
The weight of the G3-S13 CONVERGING CHEST PRESS is 645 lbs. (293 kg). To avoid injury to yourself and prevent damage to
the frame components, be sure to have proper assistance removing the frame pieces from this box. Please be sure to install the
equipment on a stable base, properly level the machine and leave at least two feet of clearence to enter and exit the machine.
Maximum user weight for this machine is 350 lbs. (159 kg).
INCLUDED TOOLS REQUIRED FOR ASSEMBLY
17MM Open-End Wrench
3MM L-Shaped Allen Wrench
4MM L-Shaped Allen Wrench
5MM L-Shaped Allen Wrench
6MM L-Shaped Allen Wrench
8MM L-Shaped Allen Wrench
10MM L-Shaped Allen Wrench
If any items are missing please contact your country’s local MATRIX dealer for assistance.
0mm 10 20 30 40 50 60 70 80 90 100 1
10 120 130 140 150 160
Step 1
Frame Detail
Flat Washer
Screw
Lock Washer
Screw
Arc Flat Washer
Arc-at Washer
Flat Washer(M10)
Lock Washer(M10)
Screw (M10X25L)
8
16
24
Qty
16
Item Description
Z07
Z08
Z16
Z23
Z07
Z08
AC1
Z16
Z23
Z16
AB1
Step 2
Input Detail
Item Description Qty
2Z17 Screw (M12X25L)
2
2
2
Stop RingC19 2
Z17
Z13
Sleeve 2D18
Z19
Lock Washer(M12)
Flat Washer(M12)
Vavy Washer
AJ2
D07
AD2
D18
Z19
Z13 Z14 Z17
AD1
D18
Z13
Z17
Z14
Z19
D07
Step 5
Item Description Qty
Washer
Screw Hex Socket 10
Z07
1
1
F02 1Small Cam
Steel Rope
Z06
Z05
Z09
Z25
F03
F08
F19
F01
F18
D18
20
2Cam Flange
Fixing Block
Big Cam
Steel Rope
1
2
F02
F08
F03
Z07
Z25
F18 Z25
Z07
AF3
F19
Z07
F03
F08
F01
Z07
Z25
Z25
1
1
1
Z09
Z06
Z05
D18
1
Sleeve
Screw (M12X25L)
Lock Washer(M12)
Flat Washer(M12)
Step 6
Item Description Qty
1
2
1
1
2
F18
F19
F22
1
1
Z10
Z11
Bearing;Rod End 3
Nut;Cap 3
Z03
F04
E-Clipper
Guide Rod;Pulley
F05 Fixing Axle;Pulley
Pulley 2F21
Z28
2
Z29 Flat Washer(M10) 2
Screw (M10X30L)Z31
Screw (M10X40L)
Cable
Cable
Cable
F19
F18
F22
Z11
Z10
Z10
Z11
AF2
F04
Z03
Z03
F05 Z28
Z29
F21
Z31
Step 3
Upholstery Detail
Item Description Qty
11Z15 Screw (M10X25L)
J31
J32
J33
1
1
1
J32
J31
Z15
Z15
J33
Back Pad
Seat Pad
Head Pad
Step 4
Weight Stack Detail
Guide Rod
Top Weight
Selector Pin
Screw
Guide Sleeve
Knurled Belt Securing Insert
10
Z03
Z03
Z05
Z12
Z26
K12
AL1
Z27
Z21
Z04
Z22
K07
AL2
Z21
Z12
Z26
Flat Washer(M8)
Lock Washer(M8)
2
2
Z22
Z04
Flat Washer(M5)
Lock Washer(M5)
Screw (M8X20L) 2
Qty
4
4
Z05
Z03
K12 Stop Ring
Z27
2
2
K07 Rubber Stack Cushions
Screw (M4X10L)
Screw (M5X16L)
E-Clipper 4
4
4
Description
Item
Step 7
Accessory Detail
Upper Cover Detail AB1
Z02
Z10
Q02
Upper Cover
Towel / Water
Z06
Description
panel
Z01
Weight Shield
Q06
Q06
Q01
Bottle Holder
Q05
Q05
Q05
Q06
B46
B47
Qty
6
6
6
2
1
2
Water Bottle Holder
DescriptionItem
Weight Shield
Upper Cover
Rubber Shield Spacer
Q02
1
Z02
6Internal Tooth Lock Washer(M4)Z20
2
1Description panelB46
B47
Z01
Z06
Q01
Q06
Q05
Rubber Tip Weight Shield Bolt(M8X40L)
Screw(M8X18L)
Screw (M8X30L)
Screw (M4X12L)
S13_conv_chest_press_r1.1.indd 2 12/13/10 8:56 AM

G3 STRENGTH
G3-S21 LATERAL RAISE
MATRIX FITNESS | 1600 LANDMARK DRIVE COTTAGE GROVE WI 53527 USA
To l l Free 866.693.4863 matrixfitness.com Fax [phone]
PART # 0000000000
REV. 1.1
ACTION FREQUENCY
Clean Upholstery Daily
Inspect Cables Daily
Clean Guide Rods Monthly
Inspect Hardware Monthly
Inspect Frame Bi-Annually
Clean Machine As Needed
Clean Grips As Needed
Lubricate Guide Rods As Needed
Upholstery & Grips should be cleaned with a non-ammonia based cleaner (like Simple Green) or a mild soap and water.
Guide rods should be lubricated with Teflon based lubricant. Apply the lubricant to a cotton cloth and then apply up and
down the guide rods.
MAINTENANCE CHECKLIST
PRODUCT SPECIFICATIONS
TECH SPECS
Overall dimensions 48”L X 51”W x 59”H (122 cm x 130 cm x 150 cm)
Weight 597 lbs (271 kg)
Shipping weight 642 lbs (291 kg)
WARRANTY (Valid in USA only)
Frame (not coatings) 10 years
Structural parts 10 years
Weight stacks 5 years
Pulleys 5 years
Pivot bearings 5 years
Any items not specified 3 years
Labor (excluding upholstery/cables/grips) 3 years
Upholstery/cables/grips/springs 1 year
IMPORTANT SAFETY INFORMATION
It is the sole responsibility of the purchaser of MATRIX Fitness Systems products to instruct all individuals, whether they
are the end user or supervising personnel on proper usage of the equipment.
It is recommended that all users of MATRIX Fitness Systems exercise equipment be informed of the following information
prior to its use.
PROPER USAGE
Do not use any equipment in any way other than designed or intended by the manufacturer. It is imperative that MATRIX
Fitness Systems equipment be used properly to avoid injury.
Keep hands and feet clear at all times from moving parts to avoid injury.
CHECK FOR DAMAGED PARTS
1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by
your country’s local MATRIX Fitness Systems dealer.
2. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain important information.
If unreadable or missing, contact your MATRIX Fitness Systems dealer for a replacement.
3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking or tipping over.
This must be performed by a licensed contractor.
4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping
your liability to a minimum. Equipment needs to be inspected at regular intervals.
5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so.
MATRIX Fitness Systems dealers will provide service and maintenance training at our corporate facility upon request.
WARNING: SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT. FOLLOW THESE PRECAUTIONS TO
AVOID INJURY!
1. Never allow children on freeweight or bench equipment. Teenagers must be supervised at all times while using
this equipment.
2. All warnings and instructions should be read and proper instruction obtained prior to use.
3. Cease exercise if you feel faint or dizzy. Obtain a medical exam before beginning an exercise program
4. Keep body, hair, clothing and fitness accessories free and clear of all moving parts.
5. Inspect the machine before use. DO NOT use machine if it appears damaged or inoperable.
6. This equipment should only be used in supervised areas where access and control are regulated by the owner.
S21_lat_raise_r1.1.indd 1 12/13/10 9:27 AM

G3-S21 LATERAL RAISE
UNPACKING G3-S21 LATERAL RAISE
Thank you for purchasing a MATRIX Fitness product. This machine is an EN957-1 and EN957-2 complaint Class S product. Your
MATRIX G3-S21 LATERAL RAISE is inspected before it is packaged. It is shipped in multiple pieces to facilitate the compact
packaging of the machine. Prior to assembly, confirm all the components by matching them with the exploded diagrams. Carefully
unpack the unit from this box and dispose of the packing materials in accordance with your local laws.
CAUTION
The weight of the G3-S21 LATERAL RAISE is 597 lbs. (271 kg). To avoid injury to yourself and prevent damage to the frame
components, be sure to have proper assistance removing the frame pieces from this box. Please be sure to install the equipment
on a stable base, properly level the machine and leave at least two feet of clearence to enter and exit the machine. Maximum user
weight for this machine is 350 lbs. (159 kg).
INCLUDED TOOLS REQUIRED FOR ASSEMBLY
17MM Open-End Wrench
3MM L-Shaped Allen Wrench
4MM L-Shaped Allen Wrench
5MM L-Shaped Allen Wrench
6MM L-Shaped Allen Wrench
8MM L-Shaped Allen Wrench
10MM L-Shaped Allen Wrench
If any items are missing please contact your country’s local MATRIX dealer for assistance.
0mm 10 20 30 40 50 60 70 80 90 100 1
10 120 130 140 150 160
Step 1
Frame Detail
Flat Washer
Screw
Lock Washer
Screw
Arc Flat Washer
C38
G14
C37
Item
24
16
8
16
Qty
Arc-at Washer
Flat Washer
Lock Washer
Screw
Description
C35
C38
C37
G14
C37
C38
C35
C35
C35
Step 2
Input Detail
D30
D34
D31
D33
D36
Flat WasherD33 2
Lock WasherD34 2
BushingD36 2
Wavy Washer 2
Screw D31 2
Description
Item Qty
Screw
D30 Screw 4
Left Cover 1
Right Cover 1
12
Flat Washer
Spring Washer
12
12
C01
C02 C40
C41C42
C41C42
C40
H22
H22 C01
C02
C42
C41
C40
H22
Step 5
Belt Routing Detail
Lock Washer
Screw
F05
Item
Flat Washer
Belt Fixer
Qty
Description
Belt
Belt Fixer
F07 6
ScrewF12 12
Flat Washer 12
Lock Washer 12
Belt F08 1
1
F17
F18
F05
AG1
F12
F07
F08
F17 F18
Step 6
Accessory Detail
Upper Cover Detail AB1
B43
B51
Q02
Upper Cover
Towel / Water
B47
Description
panel
B28
Weight Shield
Q06
Q06
Q01
Bottle Holder
Q05
Q05
Q05
Q06
B48
B24
1
Nameplate
B48
6
6
1
2
6
Internal Tooth Lock Washer
Q01 Weight Shield
Q02 Upper Cover
Q06
Q05 Rubber Shield Spacer
Rubber Tip Weight Shield Bolt
B51
Item Qty
Description
B43 Screw 6
Screw
B47 2
Screw
B28 2
B24 Water Bolttle Holder 1
Step 3
Upholstery Detail
Item
D30 19
Qty
Screw
Description
D30
D30
D30
D30
Step 4
Weight Stack Detail
Guide Rod
Top Weight
Selector Pin
Screw
Guide Sleeve
Knurled Belt Securing Insert
10
K05 B28
1010
K07
K13
25
190
280
295
235
265
250
220
205
145
160
175
115
130
70
100
85
55
40
L09
L11
K18
L14
F18
F17
2K07 Rubber Stack Cushions
E-Clipper
ScrewB28
K13
2
4
Description
Knurled Belt Securing Insert
Item
K05
Qty
1
K18 Flat Washer 2
L09 Screw 2
L11 Lock Washer 2
Lock Washer 4
L14 Screw 4
Flat Washer 4
F18
F17
S21_lat_raise_r1.1.indd 2 12/13/10 9:27 AM

G3 STRENGTH
G3-S23 CONVERGING SHOULDER PRESS
MATRIX FITNESS | 1600 LANDMARK DRIVE COTTAGE GROVE WI 53527 USA
To l l Free 866.693.4863 matrixfitness.com Fax [phone]
PART # 0000000000
REV. 1.1
ACTION FREQUENCY
Clean Upholstery Daily
Inspect Cables Daily
Clean Guide Rods Monthly
Inspect Hardware Monthly
Inspect Frame Bi-Annually
Clean Machine As Needed
Clean Grips As Needed
Lubricate Guide Rods As Needed
Upholstery & Grips should be cleaned with a non-ammonia based cleaner (like Simple Green) or a mild soap and water.
Guide rods should be lubricated with Teflon based lubricant. Apply the lubricant to a cotton cloth and then apply up and
down the guide rods.
MAINTENANCE CHECKLIST
PRODUCT SPECIFICATIONS
TECH SPECS
Overall dimensions 60”L X 59”W x 68”H (154 cm x 149 cm x 175 cm)
Weight 553 lbs (251 kg)
Shipping weight 620 lbs (281 kg)
WARRANTY (Valid in USA only)
Frame (not coatings) 10 years
Structural parts 10 years
Weight stacks 5 years
Pulleys 5 years
Pivot bearings 5 years
Any items not specified 3 years
Labor (excluding upholstery/cables/grips) 3 years
Upholstery/cables/grips/springs 1 year
IMPORTANT SAFETY INFORMATION
It is the sole responsibility of the purchaser of MATRIX Fitness Systems products to instruct all individuals, whether they
are the end user or supervising personnel on proper usage of the equipment.
It is recommended that all users of MATRIX Fitness Systems exercise equipment be informed of the following information
prior to its use.
PROPER USAGE
Do not use any equipment in any way other than designed or intended by the manufacturer. It is imperative that MATRIX
Fitness Systems equipment be used properly to avoid injury.
Keep hands and feet clear at all times from moving parts to avoid injury.
CHECK FOR DAMAGED PARTS
1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by
your country’s local MATRIX Fitness Systems dealer.
2. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain important information.
If unreadable or missing, contact your MATRIX Fitness Systems dealer for a replacement.
3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking or tipping over.
This must be performed by a licensed contractor.
4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping
your liability to a minimum. Equipment needs to be inspected at regular intervals.
5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so.
MATRIX Fitness Systems dealers will provide service and maintenance training at our corporate facility upon request.
WARNING: SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT. FOLLOW THESE PRECAUTIONS TO
AVOID INJURY!
1. Never allow children on freeweight or bench equipment. Teenagers must be supervised at all times while using
this equipment.
2. All warnings and instructions should be read and proper instruction obtained prior to use.
3. Cease exercise if you feel faint or dizzy. Obtain a medical exam before beginning an exercise program
4. Keep body, hair, clothing and fitness accessories free and clear of all moving parts.
5. Inspect the machine before use. DO NOT use machine if it appears damaged or inoperable.
6. This equipment should only be used in supervised areas where access and control are regulated by the owner.
S23_conv_shldr_press_r1.1.indd 1 12/13/10 9:39 AM

G3-S23 CONVERGING SHOULDER PRESS
UNPACKING G3-S23 CONVERGING SHOULDER PRESS
Thank you for purchasing a MATRIX Fitness product. This machine is an EN957-1 and EN957-2 complaint Class S product. Your
MATRIX G3-S23 CONVERGING SHOULDER PRESS is inspected before it is packaged. It is shipped in multiple pieces to facilitate
the compact packaging of the machine. Prior to assembly, confirm all the components by matching them with the exploded
diagrams. Carefully unpack the unit from this box and dispose of the packing materials in accordance with your local laws.
CAUTION
The weight of the G3-S23 CONVERGING SHOULDER PRESS is 553 lbs. (251 kg). To avoid injury to yourself and prevent damage
to the frame components, be sure to have proper assistance removing the frame pieces from this box. Please be sure to install
the equipment on a stable base, properly level the machine and leave at least two feet of clearence to enter and exit the machine.
Maximum user weight for this machine is 350 lbs. (159 kg).
INCLUDED TOOLS REQUIRED FOR ASSEMBLY
17MM Open-End Wrench
3MM L-Shaped Allen Wrench
4MM L-Shaped Allen Wrench
5MM L-Shaped Allen Wrench
6MM L-Shaped Allen Wrench
8MM L-Shaped Allen Wrench
10MM L-Shaped Allen Wrench
If any items are missing please contact your country’s local MATRIX dealer for assistance.
0mm 10 20 30 40 50 60 70 80 90 100 1
10 120 130 140 150 160
Step 1
Frame Detail
Flat Washer
Screw
Lock Washer
Screw
Arc Flat Washer
Arc-at Washer
Flat Washer(M10)
Lock Washer(M10)
8
16
24
Qty
16
Item Description
Z21
Z07
Z08
Z15
Z15
Z08
Z07
Z15
Z21
Z15
Z21
Z15 Z08
Z07
AB1
AC1
Screw (M10X25L)
Step 2
Input Detail
AB1
AJ2
Z10
AC1
Z10
Item Description Qty
11Screw (M10X25L)Z10
J31
J32
J33
1
1
1Back Pad
Seat Pad
Head Pad
J31
J32
J33
Step 5
Item Description Qty
Z13 Screw Hex Socket
Z07
1Steel RopeF10
F16 Cam Flange 1
F01 1
F08 1
2F12 Fixing Block
F04 Cam Flange 1
F02 1Small Cam
Steel Rope
Big Cam
16
8
1
1
1Z11
Z06
Z05
Screw (M12X25L)
Lock Washer(M12)
Flat Washer(M12)
Washer(M10)
D18 1Sleeve
F12
F08
Z13
Z07
F16
AF3
F02
F12
F04
F10
Z13
Z07
Z07
F01
Z07
Z13
AF3
Z11
Z06
Z05
D18
Step 6
Item Description Qty
1
1
1
2Z03 E-Clipper
1F04 Guide Rod;Pulley
2
Flat Washer(M10) 2
Pulley 2F21
1Fixing Axle;Pulley
F08
F10
F09
F08
F09
F10
C44 1Fix Rubber Block
Z34
Z26 Bearing;Rod End 3
NUT;Cap 3 F04
Z03
Z03
AF2
F21
C44
Z34
Z34
Z34
Z26
Z26
Z26
F07
F07
Z32
Z32
Z33
Z33
Screw (M10X40L)
Cable
Cable
Cable
Step 3
Input Arm Detail
DescriptionItem Qty
2
2
Z11
C47
Stop Ring
C19
Z28 2
2
Wavy Washer
Screw (M12X25L)
Washer
C47
C19
Z28
Z11
Z28
C19
C47
Z11
Step 4
Weight Stack Detail
Guide Rod
Top Weight
Selector Pin
Screw
Guide Sleeve
Knurled Belt Securing Insert
10
Z03
Z03
Z31
Z30
Z29
Z14
K09
K12Z17 Z18
Z17
Z18
Z03
Z31
Z29
Z30
K12
Z14
K09
AL2
K07
Item Description
Flat Waher(M5)
Lock Waher(M5)
Screw (M5X16L)
Flat Waher(M8)
Lock Waher(M8)
E-Clipper
Screw (M4X10L)
Stop Ring
Screw (M8X20L)
Qty
4
4
4
4
2
2
2
2
2
AL1
Step 7
Accessory Detail
Upper Cover Detail AB1
Z02
Z20
Q02
Upper Cover
Towel / Water
Z09
Description
panel
Z01
Weight Shield
Q07
Q07
Q05
Bottle Holder
Z24
Z24
Z24
Q07
B49
B47
Qty
6
6
6
2
1
2
Water Bottle Holder
DescriptionItem
Weight Shield
Upper Cover
Rubber Shield Spacer
Q02
1
Z24
Q07
Z02
B47
6Internal Tooth Lock Washer(M4)Z20
2
1Description panel
Z09
B49
Q05
Z01 Screw (M8X30L)
Screw (M4X12L)
Screw(M8X18L)
Rubber Tip Weight Shield Bolt(M8X40L)
S23_conv_shldr_press_r1.1.indd 2 12/13/10 9:39 AM

G3 STRENGTH
G3-S51 ABDOMINAL
MATRIX FITNESS | 1600 LANDMARK DRIVE COTTAGE GROVE WI 53527 USA
To l l Free 866.693.4863 matrixfitness.com Fax [phone]
PART # 0000000000
REV. 1.1
ACTION FREQUENCY
Clean Upholstery Daily
Inspect Cables Daily
Clean Guide Rods Monthly
Inspect Hardware Monthly
Inspect Frame Bi-Annually
Clean Machine As Needed
Clean Grips As Needed
Lubricate Guide Rods As Needed
Upholstery & Grips should be cleaned with a non-ammonia based cleaner (like Simple Green) or a mild soap and water.
Guide rods should be lubricated with Teflon based lubricant. Apply the lubricant to a cotton cloth and then apply up and
down the guide rods.
MAINTENANCE CHECKLIST
PRODUCT SPECIFICATIONS
TECH SPECS
Overall dimensions 55”L X 44”W x 59”H (140 cm x 112 cm x 150 cm)
Weight 553 lbs (251 kg)
Shipping weight 600 lbs (272 kg)
WARRANTY (Valid in USA only)
Frame (not coatings) 10 years
Structural parts 10 years
Weight stacks 5 years
Pulleys 5 years
Pivot bearings 5 years
Any items not specified 3 years
Labor (excluding upholstery/cables/grips) 3 years
Upholstery/cables/grips/springs 1 year
IMPORTANT SAFETY INFORMATION
It is the sole responsibility of the purchaser of MATRIX Fitness Systems products to instruct all individuals, whether they
are the end user or supervising personnel on proper usage of the equipment.
It is recommended that all users of MATRIX Fitness Systems exercise equipment be informed of the following information
prior to its use.
PROPER USAGE
Do not use any equipment in any way other than designed or intended by the manufacturer. It is imperative that MATRIX
Fitness Systems equipment be used properly to avoid injury.
Keep hands and feet clear at all times from moving parts to avoid injury.
CHECK FOR DAMAGED PARTS
1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by
your country’s local MATRIX Fitness Systems dealer.
2. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain important information.
If unreadable or missing, contact your MATRIX Fitness Systems dealer for a replacement.
3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking or tipping over.
This must be performed by a licensed contractor.
4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping
your liability to a minimum. Equipment needs to be inspected at regular intervals.
5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so.
MATRIX Fitness Systems dealers will provide service and maintenance training at our corporate facility upon request.
WARNING: SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT. FOLLOW THESE PRECAUTIONS TO
AVOID INJURY!
1. Never allow children on freeweight or bench equipment. Teenagers must be supervised at all times while using
this equipment.
2. All warnings and instructions should be read and proper instruction obtained prior to use.
3. Cease exercise if you feel faint or dizzy. Obtain a medical exam before beginning an exercise program
4. Keep body, hair, clothing and fitness accessories free and clear of all moving parts.
5. Inspect the machine before use. DO NOT use machine if it appears damaged or inoperable.
6. This equipment should only be used in supervised areas where access and control are regulated by the owner.
S51_abdominal_r1.1.indd 1 12/13/10 9:51 AM

G3-S51 ABDOMINAL
UNPACKING G3-S51 ABDOMINAL
Thank you for purchasing a MATRIX Fitness product. This machine is an EN957-1 and EN957-2 complaint Class S product. Your
MATRIX G3-S51 ABDOMINAL is inspected before it is packaged. It is shipped in multiple pieces to facilitate the compact
packaging of the machine. Prior to assembly, confirm all the components by matching them with the exploded diagrams. Carefully
unpack the unit from this box and dispose of the packing materials in accordance with your local laws.
CAUTION
The weight of the G3-S51 ABDOMINAL is 553 lbs. (251 kg). To avoid injury to yourself and prevent damage to the frame com-
ponents, be sure to have proper assistance removing the frame pieces from this box. Please be sure to install the equipment on
a stable base, properly level the machine and leave at least two feet of clearence to enter and exit the machine. Maximum user
weight for this machine is 350 lbs. (159 kg).
INCLUDED TOOLS REQUIRED FOR ASSEMBLY
17MM Open-End Wrench
3MM L-Shaped Allen Wrench
4MM L-Shaped Allen Wrench
5MM L-Shaped Allen Wrench
6MM L-Shaped Allen Wrench
8MM L-Shaped Allen Wrench
10MM L-Shaped Allen Wrench
If any items are missing please contact your country’s local MATRIX dealer for assistance.
0mm 10 20 30 40 50 60 70 80 90 100 1
10 120 130 140 150 160
Step 1
Frame Detail
Flat Washer
Screw
Lock Washer
Screw
Arc Flat Washer
B24
B27
B26
B24
D32
DescriptionItem
8
Qty
12
4
B24
D32
B26
B27
Screw (M10X25L)
Lock Washer(M10)
Flat Washer(M10)
Arc-at Washer
8
Step 2
Input Detail
D35
F01
Flat Key (10x8x20L)F04 1
F04
2Flat Washer(M12)F24
F23 Lock Washer(M12) 2
2Screw(M12x25L)F22
D17
B26
D20
Item Description
Flat Washer(M10)
Shoulder Bolt(M8x10x30)
Qty
1
1
1
F24
F23
F22
D17
D20
B26
D22
F24
F23
F22
1Flange BushingD35
Screw(M6x12L)
F08
F08 Belleville Washer 1
Flat Washer(M6)D22 1
Step 5
Belt Routing Detail
Belt
F12
F20
F21
F19
Lock Washer
Belt Fixer
Belt
Screw
Flat Washer
Item Description Qty
2Belt FixerF12
F19 Screw(M5x30) 4
Flat Washer(M5)F20
F21 Lock Washer(M5)
4
4
Step 6
Accessory Detail
Upper Cover Detail AB1
B43
B51
Q02
Upper Cover
Towel / Water
B28
Description
panel
B41
Weight Shield
Q07
Q07
Q01
Bottle Holder
Q06
Q06
Q06
Q07
Q07
Q06
B51
B28
B43
B41
Rubber Tip Weight Shield Bolt(M8X40L)
Rubber Shield Spacer
Internal Tooth Lock Washer(M4)
Screw(M8X18L)
Screw (M4X12L)
Screw (M8X30L)
Item Description
2
6
6
2
6
6
Qty
B26 Flat Washer(M10) 2
Screw (M10X25L)B24 2
Step 3
Upholstery Detail
Seat PadJ32 1
2
J06 Hand Pad
Back PadJ05 2
Screw (M10X25L)D33 17
QtyDescriptionItem
2
F16 Screw (M10X65L)
Sketch
J05
J06
J32
D33
F16
D33
D33
D33
D33
Step 4
Weight Stack Detail
Guide Rod
Top Weight
Selector Pin
Screw
Guide Sleeve
Knurled Belt Securing Insert
10
Item
B41 Screw(M8x30) 2
4Flat Washer(M5)F20
F21 Lock Washer(M5) 4
1Knurled Belt Securing InsertK05
K07 2Rubber Stack Cushions
4K08 E-Clipper
2Flat Washer(M8)K18
Lock Washer(M8)L14 2
K17 Screw(M8x20) 2
L10 Screw(M5x16) 4
B41
K07
F20
F21
L10
K08
K08
K05
K17L14
K18
Description Qty
S51_abdominal_r1.1.indd 2 12/13/10 9:51 AM

4
8
8
Lock W
Arc-flat W
G3S52 - BACK EXTENSION
UNPACKING G3S52 BACK EXTENSION
Thank you for purchasing a MATRIX Fitness product.Your MATRIX G3S52 Back Extension is inspected before it is packaged. Carefully unpack the unit
from this box and dispose of the packing materials in accordance with your local laws.
CAUTION
The weight of the G3S52 Back Extension is 650 lbs. (295 kg) not including the weight stack. To avoid injury to yourself and prevent damage to the frame
components, be sure to have proper assistance removing the frame pieces from this box.
Screw, Oval-Hex Socket (M10x25)C33
Item Description Sketch
6
Screw, Oval-Hex Socket (M8x30L) 2B28
Qty
Upholstery Detail
Input Detail
Frame Detail
Screw, Oval-Hex SocketD25
D32
D33 Lock Washer (M12)
Flat Washer (M32)
3
2
2
H32 Wavy Washer
Allen Head Cap Screw
C41
C43 Nylon Nut (M10) 2
2
Item Description Sketch Qty
2
C45 Screw, Oval-Hex Socket 2
C39 Flat Washer (M10) 4
C40 Lock Washer (M10) 2
D35 Bushing 1
C33 Screw, Oval-Hex Socket 2
Q08 Pivot Point Index 1
D40 1
Rubber Cap
D16 1
Spacer
Weight Stack Detail
Belt Routing Detail
Accessory Detail
4
8
12
8
Qty
Allen Head Cap Screw (M10 x25L)
Flat Washer (M10)
Lock Washer (M10)
Arc-flat Washer
Description Sketch
Allen Head Cap Screw
Lock Washer
Flat Washer
Arc-flat Washer
C60
C40
C45
C39
Item
Selector Pin
Top Weight
Knurled Belt
Securing Insert (K05)
Allen Head
Cap Screw (B28)
Guide Rod
Guide Sleeve
Lock Washer
Flat Washer
Rubber Stack Cushions
Knurled Belt Securing Insert
E-Clipper
Screw, Oval-Hex Socket
F16
L14
Screw, Oval-Hex Socket
Lock Washer (M8)
Flat Washer
L11
L13
L09
K13
K18
K07
4
4
2
4
2
4
2
2
Description Sketch
Allen Head Cap Screw
B28
K05
Item
2
1
Qty
10
K13
K07
B28
K05
L09
L11
K18
L14
L13
F16
1010
295
250
280
265
205
220
235
190
175
145
160
130
85
100
115
40
55
70
25
Qty
Lock Washer
Allen Head Cap Screw
Flat Washer
Attachment Plate
Item Description Sketch
Attachment PlateF09 2
F11 Allen Head Cap Screw 4
F16 Flat Washer 4
L13 Lock Washer (M5) 4
TOOLS NEEDED
DESCRIPTION SKETCH QUANTITY
3MM L-Shaped Allen Wrench 1
4MM L-Shaped Allen Wrench 1
5MM L-Shaped Allen Wrench 1
6MM L-Shaped Allen Wrench 1
8MM L-Shaped Allen Wrench 1
10MM L-Shaped Allen Wrench 1
Phillips Screwdriver 1
8MM Open-End Wrench 1
17MM Open-End Wrench 1
Guide Rod Lubrication 1
Hardware Bag
If any items are missing please contact your country's local Matrix dealer for assistance.
G3S52 BACK EXTENSION
G3S52 BACK EXTENSION
IMPORTANT SAFETY INFORMATION It is the sole responsibility of the purchaser of MATRIX Fitness Systems products to instruct all individuals, whether they are the end user or supervising personnel on proper usage of the equipment. It is the sole recommended that all users of MATRIX Fitness Systems exercise equipment be informed of the following information prior to its use. PROPER USAGE 1. Do not use any equipment in any way other than designed of intended by the manufacturer. It is imperative the sole recommended that all users of MATRIX Fitness Systems exercise equipment be informed MATRIX Fitness Systems equipment is used properly to avoid injury. 2. Keep hands and feet clear at all times from moving parts to avoid injury. CHECK FOR DAMAGE PARTS 1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by your country’s local MATRIX Fitness Systems dealer. 2. MANINTAIN LABELS AND NAMEPLATES: DO NOT remove labels for any reason. They contain important information. If un- readable or missing, contact your MATRIX Fitness Systems dealer for a replacement. 3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking of tipping over. A licensed contractor must be performed this, where application. 4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping your liability to a minimum. Equipment needs to be inspected at regular intervals. 5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so. MATRIX Fitness System dealers will provide service and maintenance training at our corporate facility upon request.
Matrix Fitness Systems Corp. 1610 Landmark Drive Cottage Grove WI 53527
Toll Free 866.693.4863 www.matrixfitness.com Fax [phone]
PART # MH0204510B
C41
D32 Q08
D35
H32
D25
D33
C33
D25 D33 D32
C45
C39
C40
D16
H32
D40
C43
H16
H17
H13
C33
C33
Q07 x6
Description Panel
B43 x6
B51 x6
Q05 x6
B47 x2
Weight Shield
Upper Cover x2
Step 1
Step 2
Step 3 Step 4
Step 5
Step 6
B43 Screw, (M4x12L) 6
B47 Screw, (M8x18L) 2
B51 Internal Tooth Lock Washer 6
Q01 Weight Shield 1
Q02 Upper Cover 2
Q05 Rubber Shield Spacer 6
Q07 Rubber Tip Weight Shield Bolt 6
Qty
Description Sketch Item
C45
C60
C39 C40
C45
F09
F16
L13
F11
Belt
C39
C40
B28
Towel/Water Bottle
Holder
Belt

G3S55 - ROTARY TORSO
UNPACKING G3S55 ROTARY TORSO
Thank you for purchasing a MATRIX Fitness product.Your MATRIX G3S55 Rotary Torso is inspected before it is packaged.
Carefully unpack the unit from this box and dispose of the packing materials in accordance with your local laws.
CAUTION
The weight of the G3S55 Rotary Torso is 460 lbs. (209 kg) not including the weight stack. To avoid injury to yourself
and prevent damage to the frame components, be sure to have proper assistance removing the frame pieces from this
box.
TOOLS NEEDED
DESCRIPTION SKETCH QUANTITY
3MM L-Shaped Allen Wrench 1
4MM L-Shaped Allen Wrench 1
5MM L-Shaped Allen Wrench 1
6MM L-Shaped Allen Wrench 1
8MM L-Shaped Allen Wrench 1
10MM L-Shaped Allen Wrench 1
Phillips Screwdriver 1
8MM Open-End Wrench 1
17MM Open-End Wrench 1
Guide Rod Lubrication 1
Hardware Bag
If any items are missing please contact your country's local Matrix dealer for assistance.
Weight Stack Detail
Flat Washer
Screw, Oval-Hex Socket
Knurled Belt Securing Insert
Rubber Stack Cushions
Lock Washer
L14
L13
Screw, Oval-Hex Socket
Lock Washer (M8)
E-Clipper (E-15)
L10
L11
L09
K07
K13
K05
4
4
2
2
2
2
4
1
Flat Washer
Description Sketch
Allen Head Cap Screw (M8 X 30L)
B28
B30
Item
2
4
Qty
G3S55 ROTARY TORSO
IMPORTANT SAFETY INFORMATION It is the sole responsibility of the purchaser of MATRIX Fitness Systems products to instruct all individuals, whether they are the end user or supervising personnel on proper usage of the equipment. It is the sole recommended that all users of MATRIX Fitness Systems exercise equipment be informed of the following information prior to its use. PROPER USAGE 1. Do not use any equipment in any way other than designed of intended by the manufacturer. It is imperative the sole recommended that all users of MATRIX Fitness Systems exercise equipment be informed MATRIX Fitness Systems equipment is used properly to avoid injury. 2. Keep hands and feet clear at all times from moving parts to avoid injury. CHECK FOR DAMAGE PARTS 1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by your country’s local MATRIX Fitness Systems dealer. 2. MANINTAIN LABELS AND NAMEPLATES: DO NOT remove labels for any reason. They contain important information. If un- readable or missing, contact your MATRIX Fitness Systems dealer for a replacement. 3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking of tipping over. A licensed contractor must be performed this, where application. 4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping your liability to a minimum. Equipment needs to be inspected at regular intervals. 5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so. MATRIX Fitness System dealers will provide service and maintenance training at our corporate facility upon request.
G3S55 ROTARY TORSO
Matrix Fitness Systems Corp. 1610 Landmark Drive Cottage Grove WI 53527
Toll Free 866.693.4863 www.matrixfitness.com Fax [phone]
Item Description Sketch Qty
Arc-Flat WasherB55 2
Allen Head Cap ScrewZ10 6
Z15 Flat Washer 7
Spring Washer (M10)L16 7
Allen Head Cap ScrewZ17 3
1
Item Description Sketch Qty
Screw, Oval-Hex Socket (M10x25)C33 18
Item Description Sketch Qty
Arc-Flat WasherB55 2
Allen Head Cap Screw (M10x25L)Z10 6
Z15 Flat Washer (M10)
L16
Allen Head Cap Screw (M10x30)Z17
CoverD25
PART # MH0204206B
B55
Z10
Z17
Z16
Z15
D25
C33 x18
K13
L14
L13
B30
K05
B28
L09
L11 L10
Guide Sleeve
Guide Rod
Screw
Selector Pin
Top Weight
Knurled Belt
Securing Insert
K07
BELT
F24
F33
F32
F31
Item Description Sketch Qty
Attachment PlateF24 2
Allen Head Cap ScrewF31 4
F33 Flat Washer 4
Lock WasherF32 4
Item Description Sketch Qty
Flat WasherB51
Screw (M4x12L)B43
6
Rubber Tip Weight Shield BoltQ07
Rubber Shield SpacerQ10
6
6
Allen Head Cap Screw (M8x30) 2
B28
6
Allen Head Cap Screw (M8x18) 2
B47
B28
B43
B51
Tower/Water
Bottle Holder Description
Panel
Q07 x6
Accessory Detail
Q10
B47
Q10
Step 1
Step 2
Step 3
Step 5
Step 5

G3S73 - PRONE LEG CURL
UNPACKING G3S73 PRONE LEG CURL
Thank you for purchasing a MATRIX Fitness product. Carefully unpack the unit from this box and dispose of the packing
materials in accordance with your local laws.
CAUTION
The weight of the G3S73 Prone Leg Curl is 600 lbs. (272 kg) not including the weight stack. To avoid injury to yourself
and prevent damage to the frame components, be sure to have proper assistance removing the frame pieces from this
box.
G3S73
PRONE LEG CURL
IMPORTANT SAFETY INFORMATION It is the sole responsibility of the purchaser of MATRIX Fitness Systems products to instruct all individuals, whether they are the end user or supervising personnel on proper usage of the equipment. It is the sole recommended that all users of MATRIX Fitness Systems exercise equipment be informed of the following information prior to its use. PROPER USAGE 1. Do not use any equipment in any way other than designed of intended by the manufacturer. It is imperative the sole recommended that all users of MATRIX Fitness Systems exercise equipment be informed MATRIX Fitness Systems equipment is used properly to avoid injury. 2. Keep hands and feet clear at all times from moving parts to avoid injury. CHECK FOR DAMAGE PARTS 1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by your country’s local MATRIX Fitness Systems dealer. 2. MANINTAIN LABELS AND NAMEPLATES: DO NOT remove labels for any reason. They contain important information. If un- readable or missing, contact your MATRIX Fitness Systems dealer for a replacement. 3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking of tipping over. A licensed contractor must be performed this, where application. 4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping your liability to a minimum. Equipment needs to be inspected at regular intervals. 5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so. MATRIX Fitness System dealers will provide service and maintenance training at our corporate facility upon request.
Step 1
Input Detail
Step 2
G3S73 PRONE LEG CURL
Description Sketch
Wavy Washer
Bushing Set
Shaft
Screw, Oval-Hex Socket (M10)C22
D17
B52
B54
Item
2
2
1
Screw Cover
D28
1
2
Qty
Allen Head Cap Screw (M12)D45 3
Lock Washer (M12)D46 3
Upholstry Detail
Step 3
Belt Routing Detail
Step 5
Step 6
TOOLS NEEDED
DESCRIPTION SKETCH QUANTITY
3MM L-Shaped Allen Wrench 1
4MM L-Shaped Allen Wrench 1
5MM L-Shaped Allen Wrench 1
6MM L-Shaped Allen Wrench 1
8MM L-Shaped Allen Wrench 1
10MM L-Shaped Allen Wrench 1
Phillips Screwdriver 1
8MM Open-End Wrench 1
17MM Open-End Wrench 1
Guide Rod Lubrication 1
Hardware Bag
If any items are missing please contact your country's local Matrix dealer for assistance.
Flat Washer (M12)D47 3
Pivot Point IndexQ07 1
ShaftD21 1
Description Sketch
Screw,Oval-Hex Socket
(M10x25L)
C22
Item
16
Qty Weight Stack Detail
Step 4
Description Sketch
Item Qty
Allen Head Cap Screw
Flat Washer (M5)
Attachment Plate
Lock Washer (M5)F15
F14
F08
F13 4
4
4
2
Belt
F07 1
Nylon Nut (M5)
F60 4
K07
B49
F14
F15
L14
K13
K18 C54 K17
K05
2
K07 Rubber Stack Cushions
E-Clipper (E-15)
Allen Head Cap Screw (M8 X 30L)
K13
B49 2
4
Description Sketch
Knurled Belt Securing Insert
Item
K05
Qty
1
K17 Screw, Oval-Hex Socket (M8 X 20L) 2
K18 Flat Washer (M8) 2
Lock Washer (M8) 2
4
4
4
Screw, Oval-Hex Socket (M5 X 16L)
Lock Washer (M5)
Flat Washer
C54
F14
F15
L14
Guide Sleeve
Top Weight
Selector Pin
Guide Rod
Allen Head Cap
Screw (M8x30L)
Knurled Belt
Securing Insert (K05)
10
130
220
280
265
295
235
250
175
190
205
145
160
100
115
55
70
85
25
40
10
Qty
Item Description
C25
C24
C26
J18
Sketch
Lock Washer (M10)
Flat Washer (M10)
Allen Head Cap Screw (M10x25L)
Arc-flat Washer
12
12
18
6
Flat Washer (C32)
Lock Washer (C24)
Allen Head Cap Screw (C25)
Arc Flat Washer (C26)
C25
C25
C24
J18
C26
D46
D45
D47 Q07
D45
D47 D46
D17 C22
B52
B54
C22
Matrix Fitness Systems Corp. 1610 Landmark Drive Cottage Grove WI 53527
Toll Free 866.693.4863 www.matrixfitness.com Fax [phone]
PART # MH0204521B
Accessory Detail
Q38 Q37
B49
Z10 Description Panel
Weight Shield
Q06 x6
B43 x6
B51 x6
Q05 x6
Weight Shield
Towel/Water
Bottle Holder
Upper Cover x2
Allen Head Cap Screw (M8x30L)
B51
B43 Screw (W4x12L)
B49
Rubber Tip Weight Shield Bolt
Rubber Shield SpacerQ05
Q06
2
6
6
6
6
Item Description Sketch Qty
Internal Tooth Lock W asher (M4)
Small Cap Screw (M8x18L)Z10 2
Rubber Tip Weight Shield Bolt
Rubber Shield SpacerQ37
Q38
4
4
B54
B52D21
D28
F08
F13
F15
F14
F60
Lock Washer
Screw
Belt Fixer
Flat Washer
Belt
Nylon Nut

Step 1
G3S77 CALF PRESS
G3S77 CALF PRESS
G3S77 - CALF PRESS
UNPACKING G3S77 CALF PRESS
Thank you for purchasing a MATRIX Fitness product. Your MATRIX G3S77 Calf Press is inspected before it is packaged. Carefully unpack the unit
from this box and dispose of the packing materials in accordance with your local laws.
CAUTION
The weight of the G3S77 Calf Press is 670 lbs. (304 kg) not including the weight stack. To avoid injury to yourself and prevent damage to theframe
components, be sure to have proper assistance removing the frame pieces from this box.
TOOLS NEEDED
DESCRIPTION SKETCH QUANTITY
3MM L-Shaped Allen Wrench 1
4MM L-Shaped Allen Wrench 1
5MM L-Shaped Allen Wrench 1
6MM L-Shaped Allen Wrench 1
8MM L-Shaped Allen Wrench 1
10MM L-Shaped Allen Wrench 1
Phillips Screwdriver 1
8MM Open-End Wrench 1
17MM Open-End Wrench 1
Guide Rod Lubrication 1
Hardware Bag
If any items are missing please contact your country's local Matrix Fitness Systems dealer for assistance.
Step 6
Weight Stack Detail
2
K07 Rubber Stack Cushions
E-Clipper (E-15)
Allen Head Cap Screw (M8 X 30L)
K13
B28 2
4
Description Sketch
Knurled Belt Securing Insert
Item
K05
Qty
1
K17 Screw, Oval-Hex Socket (M8 X 20L) 2
K18 Flat Washer (M8) 2
Lock Washer (M8) 2
4
4
4
Screw, Oval-Hex Socket (M5 X 16L)
Lock Washer (M8)
Flat Washer (M5)
L11
F14
F13
L14
Guide Sleeve
Selector Pin
Screw
Guide Rod
Top Weight
K07
K05
K13
B28
K17
L11
K18
L14
F13
F14
Knurled Belt
Securing
Insert (K05)
10
130
220
280
265
295
235
250
175
190
205
145
160
100
115
55
70
85
25
40
10
Flat Washer
Lock Washer
12Allen Head Cap Screw (M10 X 80L)
C44
8
4Arc-flat Washer (M10)
Flat Washer (M10)
C60
8Lock Washer (M10)C45
C46
QtyDescription Sketch
Item
C46
Frame Detail
Input Detail
Allen Head Cap Screw
C44
C60
Arc-flat Washer
Belt Routing Detail
Item Description Sketch Qty
Belt
Flat Waher
Attachment Plate
Allen Head Cap Screw
Lock Washer
Screw (M8 X 20L)C48 4
F15
F13
F14
F03
Belt
Belt FixerF03 2
F13 Lock Washer (M5) 4
Flat Washer (M5) 4F14
F15 Allen Cap Screw (M5x35L) 4
C52
C53
C51
Item
4
Flat Washer (M12)
Lock Washer (M12) 4
QtyDescription Sketch
Allen Head Cap Screw 4
C51 C52
C53
C51
C53
C52
Accessory Detail
Upholstry Detail
Description Sketch
Item
C47 Allen Head Cap Screw (M10 X 25L)
Qty
6
C47
C47
C48
IMPORTANT SAFETY INFORMATION It is the sole responsibility of the purchaser of MATRIX Fitness Systems products to instruct all individuals, whether they are the end user or supervising personnel on proper usage of the equipment. It is the sole recommended that all users of MATRIX Fitness Systems exercise equipment be informed of the following information prior to its use. PROPER USAGE 1. Do not use any equipment in any way other than designed of intended by the manufacturer. It is imperative the sole recommended that all users of MATRIX Fitness Systems exercise equipment be informed MATRIX Fitness Systems equipment is used properly to avoid injury. 2. Keep hands and feet clear at all times from moving parts to avoid injury. CHECK FOR DAMAGE PARTS 1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by your country’s local MATRIX Fitness Systems dealer. 2. MANINTAIN LABELS AND NAMEPLATES: DO NOT remove labels for any reason. They contain important information. If un- readable or missing, contact your MATRIX Fitness Systems dealer for a replacement. 3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking of tipping over. A licensed contractor must be performed this, where application. 4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping your liability to a minimum. Equipment needs to be inspected at regular intervals. 5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so. MATRIX Fitness System dealers will provide service and maintenance training at our corporate facility upon request.
Matrix Fitness Systems Corp. 1610 Landmark Drive Cottage Grove WI 53527
Toll Free 866.693.4863 www.matrixfitness.com Fax [phone]
Step 2
Step 4
Step 3
Step 5
PART # MH0204524B
Screw (M8 X 30L)
B43 Screw (M4 X 12L)
B28
Rubber Tip Weight Shield Bolt
Rubber Shield Spacer
Q05
Q06
Internal Tooth Lock Washer
B51
2
6
6
6
6
Item Description Sketch Qty
B47 Screw (M8 X 18L) 2
B28 x2
B47 x2
Bottle Holder
Towel / Water
Description
Panel
Q06 x6
Weight Shield
B43 x6
B51 x6
Upper Cover x2
C45

G3S75
HIP ABDUCTOR
IMPORTANT SAFETY INFORMATION It is the sole responsibility of the purchaser of MATRIX Fitness Systems products to instruct all individuals, whether they are the end user or supervising personnel on proper usage of the equipment. It is the sole recommended that all users of MATRIX Fitness Systems exercise equipment be informed of the following information prior to its use. PROPER USAGE 1. Do not use any equipment in any way other than designed of intended by the manufacturer. It is imperative the sole recommended that all users of MATRIX Fitness Systems exercise equipment be informed MATRIX Fitness Systems equipment is used properly to avoid injury. 2. Keep hands and feet clear at all times from moving parts to avoid injury. CHECK FOR DAMAGE PARTS 1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by your country’s local MATRIX Fitness Systems dealer. 2. MANINTAIN LABELS AND NAMEPLATES: DO NOT remove labels for any reason. They contain important information. If un- readable or missing, contact your MATRIX Fitness Systems dealer for a replacement. 3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking of tipping over. A licensed contractor must be performed this, where application. 4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping your liability to a minimum. Equipment needs to be inspected at regular intervals. 5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so. MATRIX Fitness System dealers will provide service and maintenance training at our corporate facility upon request.
Step 1
Input Detail
Step 2
G3S75 HIP ABDUCTOR
Description Sketch
Flat Washer (M8)
Screw (M8x30L)
Bushing
Lock Washer (M8)L11
D21
B28
L10
Item
8
8
2
Set Screw (M5x25L)
D44
2
8
Qty
Screw (M5x10L)D41 2
Flat Washer (M12)H30 2
Upholstry Detail
Step 3
Step 5
Accessory Detail
Step 6
TOOLS NEEDED
DESCRIPTION SKETCH QUANTITY
3MM L-Shaped Allen Wrench 1
4MM L-Shaped Allen Wrench 1
5MM L-Shaped Allen Wrench 1
6MM L-Shaped Allen Wrench 1
8MM L-Shaped Allen Wrench 1
10MM L-Shaped Allen Wrench 1
Phillips Screwdriver 1
8MM Open-End Wrench 1
17MM Open-End Wrench 1
Guide Rod Lubrication 1
Hardware Bag
If any items are missing please contact your country's local Matrix dealer for assistance.
Lock Washer (M12)H24 2
Screw (M12x25L)H12 2
Cam StopperD26 1
Nylon Nut (M8)E10 8
Description Sketch
Screw (M10x25L)
Item Qty Weight Stack Detail
Step 4
Flat Washer
Arc-flat
Washer
Lock
Washer
G35 x24G34 x16
G33 x16
Qty
Item Description
G35
G34
G37
G33
Sketch
Lock Washer (M10)
Flat Washer (M10)
Screw (M10x25L)
Arc-flat Washer (M10)
16
16
24
8
Matrix Fitness Systems Corp. 1610 Landmark Drive Cottage Grove WI 53527
Toll Free 866.693.4863 www.matrixfitness.com Fax [phone]
Allen Head
Cap Screw
PART # MH0204523B
D42 x13
13
D42
G3S75- HIP ABDUCTOR
UNPACKING G3S75 HIP ABDUCTOR
Thank you for purchasing a MATRIX Fitness product. Carefully unpack the unit from this box
and dispose of the packing materials in accordance with your local laws.
CAUTION
The weight of the G3S75 Hip Abductor is 703 lbs. (319 kg) not including the weight stack. To
avoid injury to yourself and prevent damage to the frame components, be sure to have proper
assistance removing the frame pieces from this box.
CABLE - D17
E10 x8
H12 x2
H24 x2
H30 x2
D21 x2
D41 x2
D44 x2 B28 x8
L11 x8
L10 x8
D47 x1
D18 x1
D26 x1
D41
ScrewD47 1
SpacerD18 1
2
K07 Rubber Stack Cushions
E-Clipper (E-15)
Allen Head Cap Screw (M8 X 30L)
K13
B28 2
4
Description Sketch
Knurled Belt Securing Insert
Item
K05
Qty
1
L09 Screw, Oval-Hex Socket (M8 X 20L) 2
K18 Flat Washer (M8) 2
Lock Washer (M8) 2
4
4
4
Screw, Oval-Hex Socket (M5 X 16L)
Lock Washer (M5)
Flat Washer (M5)
L11
F24
F25
L14
Knurled Belt
Securing Insert
10
Top Weight
Selector Pin
Screw
Guide Rod
Guide Sleeve
INCREMENTAL
WEIGHT
K07 x2
K05 x1
K13 x4
B28 x2
L09 x2
L11 x2
K18 x2
L14 x4
F25 x4
F24 x4
130
220
280
265
295
235
250
175
190
205
145
160
100
115
55
70
85
25
40
10
Belt & Cable Routing Detail Description Sketch
Item Qty
Allen Head Cap Screw
Belt Fixer
Flat Washer
Lock WasherF25
F24
F22
F06
4
2
4
4
4
Screw, Oval-Hex SocketG31
Screw (M8 X 30L)
B43 Screw (M4 X 12L)
B28
Rubber Tip Weight Shield Bolt
Rubber Shield Spacer
Q05
Q06
Internal Tooth Lock Washer
B51
2
6
6
6
6
Item Description Sketch Qty
B47 Screw (M8 X 18L) 2
Screw
Flat Washer
Belt
Lock Washer
Belt Fixer
B28 x2
B47 x2
Bottle Holder
Towel / Water
Description
Panel
Q06 x6
Weight Shield
B43 x6
B51 x6
Upper Cover x2
G31
F22
F25
F24
F06
BELT

G3 STRENGTH
LEG PRESS
MATRIX FITNESS SYSTEMS | 1600 LANDMARK DRIVE COTTAGE GROVE WI 53527 USA
To l l Free 866.693.4863 matrixfitness.com Fax [phone]
PART # MH0204515B
REV. 1.4
ACTION FREQUENCY
Clean Upholstery Daily
Inspect Cables Daily
Clean Guide Rods Monthly
Inspect Hardware Monthly
Inspect Frame Bi-Annually
Clean Machine As Needed
Clean Grips As Needed
Lubricate Guide Rods As Needed
Upholstery & Grips should be cleaned with a non-ammonia based cleaner (like Simple Green) or a mild soap and water.
Guide rods should be lubricated with Teflon based lubricant. Apply the lubricant to a cotton cloth and then apply up and
down the guide rods.
MAINTENANCE CHECKLIST
PRODUCT SPECIFICATIONS
TECH SPECS
Overall dimensions 79”L X 42”W x 72”H (201 cm x 107 cm x 183 cm)
Weight 920 lbs (417 kg)
Shipping weight 1040 lbs (472 kg)
WARRANTY (Valid in USA only)
Frame (not coatings) 10 years
Structural parts 10 years
Weight stacks 5 years
Pulleys 5 years
Pivot bearings 5 years
Any items not specified 3 years
Labor (excluding upholstery/cables/grips) 3 years
Upholstery/cables/grips/springs 1 year
IMPORTANT SAFETY INFORMATION
It is the sole responsibility of the purchaser of MATRIX Fitness Systems products to instruct all individuals, whether they
are the end user or supervising personnel on proper usage of the equipment.
It is recommended that all users of MATRIX Fitness Systems exercise equipment be informed of the following information
prior to its use.
PROPER USAGE
Do not use any equipment in any way other than designed or intended by the manufacturer. It is imperative that MATRIX
Fitness Systems equipment be used properly to avoid injury.
Keep hands and feet clear at all times from moving parts to avoid injury.
CHECK FOR DAMAGED PARTS
1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by
your country’s local MATRIX Fitness Systems dealer.
2. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain important information.
If unreadable or missing, contact your MATRIX Fitness Systems dealer for a replacement.
3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking or tipping over.
This must be performed by a licensed contractor.
4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping
your liability to a minimum. Equipment needs to be inspected at regular intervals.
5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so.
MATRIX Fitness Systems dealers will provide service and maintenance training at our corporate facility upon request.
WARNING: SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT. FOLLOW THESE PRECAUTIONS TO
AVOID INJURY!
1. Never allow children on freeweight or bench equipment. Teenagers must be supervised at all times while using
this equipment.
2. All warnings and instructions should be read and proper instruction obtained prior to use.
3. Cease exercise if you feel faint or dizzy. Obtain a medical exam before beginning an exercise program
4. Keep body, hair, clothing and fitness accessories free and clear of all moving parts.
5. Inspect the machine before use. DO NOT use machine if it appears damaged or inoperable.
6. This equipment should only be used in supervised areas where access and control are regulated by the owner.
S70_leg_press_r1.4.indd 1 8/9/10 8:10 AM

G3-S70 LEG PRESS
UNPACKING G3-S70 LEG PRESS
Thank you for purchasing a MATRIX Fitness product. This machine is an EN957-1 and EN957-2 complaint Class S product. Your
MATRIX G3-S70 LEG PRESS is inspected before it is packaged. It is shipped in multiple pieces to facilitate the compact
packaging of the machine. Prior to assembly, confirm all the components by matching them with the exploded diagrams. Carefully
unpack the unit from this box and dispose of the packing materials in accordance with your local laws.
CAUTION
The weight of the G3-S70 LEG PRESS is 920 lbs. (417 kg) including the weight stack. To avoid injury to yourself and prevent
damage to the frame components, be sure to have proper assistance removing the frame pieces from this box. Please be sure to
install the equipment on a stable base, properly level the machine and leave at least two feet of clearence to enter and exit the
machine. Maximum user weight for this machine is 300 lbs. (136 kg).
INCLUDED TOOLS REQUIRED FOR ASSEMBLY
6MM L-Shaped Allen Wrench
8MM L-Shaped Allen Wrench
10MM L-Shaped Allen Wrench
17MM Open-End Wrench
If any items are missing please contact your country’s local MATRIX dealer for assistance.
0mm 10 20 30 40 50 60 70 80 90 100 1
10 120 130 140 150 160
Step 1
Frame Detail
15
15
23
Lock Washer(M10)
Screw ( M10x25L)
Flat Washer (M10)
Qty
8
Screw
Screw
Lock Washer
Flat Washer
Flat Washer
Screw
Arc-at Washer
Description
Lock Washer
Arc-at Washer
C21
C61
C60
C22
Item
C21
C22
C61
C60
C61
C22
C61
C21
Step 2
Frame Detail
6
Screw (M10x85L)
Nylon Nut (M10)
Flat Washer (M10)
Lock Washer (M10)
Screw (M10x25L)
F09
2
Qty
6
2
2
6
C31
Description
Item
C61
C21
C60
C22
Arc-at Washer
F09 C61
C21
C60
C22
C61
C61
C22
C21
C31
C22
C21
Step 3
Input Detail
Screw (M8x18L)B72
Flat Washer (M12)
Description Panel 1B70
Lock Washer (M8)
Flat Washer (M8)
Screw (M8X20L)
Wavy Washer
Screw (M12x25L)
2
2
6
6
6
2
6
6
6
BushingD40
D34
D33
K17
F31
L10
L11
D39
QtyDescriptionItem
C30 4
Lock Washer (M12)
S-20c/lamp(C-shaped)
D32 Lock Washer 4
D40
K17
B72
B70
D39
D34
D39
D33
D33
D34
F31
D39
D39
D39
F31
D33
D34
D39
D33
D34
L11
L10
D34
D33
D33
D34
C30
C30
C30
C30
D40
D32
D32
D32
D32
Step 6
Cable Routing Detail QtyItem Description
TightwireF02 1
F02
F02
10
40
55
25
85
100
145
130
115
190
175
160
205
70
Step 7
Accessory Detail
B47
Rubber Tip Weight Shield Bolt(M8x40L)
Internal Tooth Lock Washer
Screw (M4x12L)
Screw (M8x30L)
6
6
6
1
2
Qty
6
1
2
B51
Water Bottle Holder
B47
Q05 Rubber Shield Spacer
Q06
Description
B28
Item
B43
Q01
Q02 Upper Cover
Weight Shield
Q01
AB3
B51
B43
B51
B43
B51
B43
Upper Cover
Q02
B28
Towel / Water
Bottle Holder
Q05
Q06
Weight Shield
Step 4
Upholstery Detail QtyItem
C20 10
C20
C20
Description
Screw (M10X25L)
Step 5
Weight Stack Detail
K13
K17
F11
L13
L14
K18 L11
Guide Sleeve
Guide Rod
Screw
Selector Pin
Top Weight
K07
K13
Lock Washer (M5)
Lock Washer (M8)
Screw (M5X16L)
Screw( M8X20L)
Flat Washer (M8)
Flat Washer (M5)
K17
4
4
2
2
4
Qty
4
2
L14
L13
L11
F11
Item Description
K18
E-Clipper
Rubber block(Elastomer)K07 2
10
10
25
70
55
40
115
100
85
130
160
145
175
190
235
220
205
265
280
250
295
S70_leg_press_r1.4.indd 2 8/9/10 8:10 AM

G3S71 - LEG EXTENSION
UNPACKING G3S71 LEG EXTENSION
Thank you for purchasing a MATRIX Fitness product. Carefully unpack the unit from this box and dispose of the packing
materials in accordance with your local laws.
CAUTION
The weight of the G3S71 Leg Extension is 569 lbs. (258 kg) not including the weight stack. To avoid injury to yourself
and prevent damage to the frame components, be sure to have proper assistance removing the frame pieces from this
box.
G3S71
LEG EXTENSION
IMPORTANT SAFETY INFORMATION It is the sole responsibility of the purchaser of MATRIX Fitness Systems products to instruct all individuals, whether they are the end user or supervising personnel on proper usage of the equipment. It is the sole recommended that all users of MATRIX Fitness Systems exercise equipment be informed of the following information prior to its use. PROPER USAGE 1. Do not use any equipment in any way other than designed of intended by the manufacturer. It is imperative the sole recommended that all users of MATRIX Fitness Systems exercise equipment be informed MATRIX Fitness Systems equipment is used properly to avoid injury. 2. Keep hands and feet clear at all times from moving parts to avoid injury. CHECK FOR DAMAGE PARTS 1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by your country’s local MATRIX Fitness Systems dealer. 2. MANINTAIN LABELS AND NAMEPLATES: DO NOT remove labels for any reason. They contain important information. If un- readable or missing, contact your MATRIX Fitness Systems dealer for a replacement. 3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking of tipping over. A licensed contractor must be performed this, where application. 4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping your liability to a minimum. Equipment needs to be inspected at regular intervals. 5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so. MATRIX Fitness System dealers will provide service and maintenance training at our corporate facility upon request.
Step 1
Input Detail
Step 2
G3S71 LEG EXTENSION
Description Sketch
Pivot Point Index
Allen Head Cap Screw
Flat Washer(M12)
Screw (M12x25)F32
D23
B31
D19
Item
1
3
3
Lock Washer (M12)
D24
3
4
Qty
BushingD25 1
Nylon Nut(M8)E27 4
Wavy WasherF31 2
Upholstry Detail
Step 4
Belt Routing Detail
Step 6
Accessory Detail
Step 7
TOOLS NEEDED
DESCRIPTION SKETCH QUANTITY
3MM L-Shaped Allen Wrench 1
4MM L-Shaped Allen Wrench 1
5MM L-Shaped Allen Wrench 1
6MM L-Shaped Allen Wrench 1
8MM L-Shaped Allen Wrench 1
10MM L-Shaped Allen Wrench 1
Phillips Screwdriver 1
8MM Open-End Wrench 1
17MM Open-End Wrench 1
Guide Rod Lubrication 1
Hardware Bag
If any items are missing please contact your country's local Matrix dealer for assistance.
Description Sketch
Screw, Oval-Hex SocketC25
Item
8
Qty Weight Stack Detail
Step 5
Description Sketch
Item Qty
Allen Head Cap Screw
Flat Washer (M5)
Lock Washer (M5)F18
F17
Attachment Plate
F08
F21 4
4
2
Belt
F09 1
Water Bottle Holder
B29 1
Screw (M8x30)
B28 2
4
K07
B28
F17
L13
L14
K12
K18 L11 L09
K05
2
K07 Rubber Stack Cushions
E-Clipper (E-15)
Allen Head Cap Screw (M8 X 30L)
K12
B28 2
4
Description Sketch
Knurled Belt Securing Insert
Item
K05
Qty
1
L09 Screw, Oval-Hex Socket (M8x20L) 2
K18 Flat Washer (M8) 2
Lock Washer (M8) 2
4
4
4
Screw, Oval-Hex Socket (M5 X 16L)
Lock Washer
Flat Washer
L11
F17
L13
L14
Guide Sleeve
Selector Pin
Allen Head Cap
Screw
Guide Rod
Top Weight
Knurled Belt Securing
Insert
10
130
220
280
265
295
235
250
175
190
205
145
160
100
115
55
70
85
25
40
10
Qty
Item Description
C47
C27
D32
C26
Sketch
Lock Washer (M10)
Flat Washer (M10)
Allen Head Cap Screw
Allen Head Cap Screw
Arc-flat Washer
8
8
12
4
Flat Washer
Lock Washer
Arc Flat Washer
Lock Washer
Flat Washer
Allen Head Cap Screw
Attachment Plate
Belt
Matrix Fitness Systems Corp. 1610 Landmark Drive Cottage Grove WI 53527
Toll Free 866.693.4863 www.matrixfitness.com Fax [phone]
PART # MH0204513B
C27
C26
C47
C47
D32
F32
D23
D24
B31
E27
F31
D25
D19
F31
F32
D23
D24
Stop Plate Detail
Step 3
Description Sketch
Flat Washer(M8)
Screw (M8x12)C52
L10
Item
6
6
Qty
C52
L10
L10 C52
C25
C25
F17
F08
B28
B29
BELT - F09
F18
F21
150
170
160
60
100
90
80
70
140
130
120
110
20
10
50
40
30
Frame Detail
Rubber Tip Weight Shield Bolt
Rubber Shield SpacerQ05
Q06
6
6
Item Description Sketch Qty
B51 3
Internal Tooth Lock Washer
B58 Description Panel 1
B43 Screw (M4x12L) 6
Q06 x6
B43 x6
B51 x6
Q05 x6
Weight Shield
Upper Cover x2
Z60
Description panel
B58
Step 1
Step 2
Z60 Screw (M8x30L) 2

G3S72 - SEATED LEG CURL
UNPACKING G3S72 SEATED LEG CURL
Thank you for purchasing a MATRIX Fitness product. Your MATRIX G3S72 Seated Leg Curl is inspected before it is
packaged. Carefully unpack the unit from this box and dispose of the packing materials in accordance with your local
laws.
CAUTION
The weight of the G3S72 Seated Leg Curl is 571 lbs. (259 kg) not including the weight stack. To avoid injury to yourself
and prevent damage to the frame components, be sure to have proper assistance removing the frame pieces from this
box.
Step 5
Frame Detail
Belt Routing Detail
D28
H11
D29
D32
D26
Item
4Flat Washer (M12)
Washer
Lock Washer (M12)
1
4
Description Sketch
4
1
Qty
Screw (12x30)
Input Detail
Pivot Point Index
H19 1Spring
H20
F31
Pin
Wavy washer
1
2
F24 Spacer 1
Upholstery Detail
C44
Item
12
Qty
Screw (M10x25)
Description Sketch
Step 4
Weight Stack Detail
Selector Pin
Top Weight
Knurled Belt
Securing Insert
Screw
Guide Rod
Guide Sleeve
Flat Washer (M5)
Screw (M5x16L)
Knurled Belt Securing Insert
Rubber Stack Cushions
Lock Washer
L14
F18
Screw (M8x20L)
Lock Washer (M8)
E-Clipper (E-15)
F17
L11
L09
K07
K13
K05
4
4
4
2
2
2
4
1
Flat Washer (M5)
Description Sketch
Screw (M8 X 20L)
B28
K18
Item
2
2
Qty
10
K13
L14
F18
F17
12Allen Cap Screw (M10 X 25L)
C47
8
4Arc-flat Washer (M10)
Flat Washer (M10)
D30
C45
8Lock Washer (M10)
C46
QtyDescription Sketch
Item
Step 1
Step 2 Step 6
Accessory Detail
TOOLS NEEDED
DESCRIPTION SKETCH QUANTITY
3MM L-Shaped Allen Wrench 1
4MM L-Shaped Allen Wrench 1
5MM L-Shaped Allen Wrench 1
6MM L-Shaped Allen Wrench 1
8MM L-Shaped Allen Wrench 1
10MM L-Shaped Allen Wrench 1
Phillips Screwdriver 1
8MM Open-End Wrench 1
17MM Open-End Wrench 1
Guide Rod Lubrication 1
Hardware Bag
If any items are missing please contact your country's local Matrix Fitness Systems dealer for assistance.
Step 3
Qty
Lock Washer
Screw
Flat Washer
Belt Fixer
Item Description Sketch
Belt FixerF09 2
BeltF08 1
F12 Screw (M5x35L) 4
F17 Flat Washer (M5) 4
F18 Lock Washer (M5) 4
Belt
G3S72 SEATED LEG CURL
G3S72 SEATED LEG CURL
IMPORTANT SAFETY INFORMATION It is the sole responsibility of the purchaser of MATRIX Fitness Systems products to instruct all individuals, whether they are the end user or supervising personnel on proper usage of the equipment. It is the sole recommended that all users of MATRIX Fitness Systems exercise equipment be informed of the following information prior to its use. PROPER USAGE 1. Do not use any equipment in any way other than designed of intended by the manufacturer. It is imperative the sole recommended that all users of MATRIX Fitness Systems exercise equipment be informed MATRIX Fitness Systems equipment is used properly to avoid injury. 2. Keep hands and feet clear at all times from moving parts to avoid injury. CHECK FOR DAMAGE PARTS 1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by your country’s local MATRIX Fitness Systems dealer. 2. MANINTAIN LABELS AND NAMEPLATES: DO NOT remove labels for any reason. They contain important information. If un- readable or missing, contact your MATRIX Fitness Systems dealer for a replacement. 3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking of tipping over. A licensed contractor must be performed this, where application. 4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping your liability to a minimum. Equipment needs to be inspected at regular intervals. 5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so. MATRIX Fitness System dealers will provide service and maintenance training at our corporate facility upon request.
Matrix Fitness Systems Corp. 1610 Landmark Drive Cottage Grove WI 53527
Toll Free 866.693.4863 www.matrixfitness.com Fax [phone]
PART # MH0204514B
Lock Washer
Screw
Flat Washer
Arc-flat Washer
Screw
C47
C46
C47
D30
C45
C47
D30
F17
F18
F09
F12
BELT - F08
40
160
150
170
140
130
120
110
100
90
80
70
60
50
30
20
10
F31
D28
D29
D32
D29
D28
F24
D32
D29
D28
F31
H11 H19
D28
D32 H20
D26
D32
D32
C44 x12
Screw (M8 X 30L)
B43 Screw (M4 X 12L)
B27
Rubber Tip Weight Shield Bolt
Rubber Shield Spacer
Q05
Q06
Internal Tooth Lock Washer (M4)
B51
2
6
6
6
6
Item Description Sketch Qty
B47 Screw (M8 X 18L) 2
Water Bottle Holder
B26 1
B27 x2
B47 x2
Bottle Holder
Towel / Water
Description
Panel
Q06 x6
Weight Shield
B43 x6
B51 x6
Upper Cover x2
130
180
170
160
150
140
40
120
110
100
90
80
70
60
50
30
10
K05
L09
L11
K18
B28
D29
Q05 x6
K07

G3-S33
Diverging Lat Pulldown
IMPORTANT SAFETY INFORMATION It is the sole responsibility of the purchaser of MATRIX Fitness Systems products to instruct all individuals, whether they are the end user or supervising personnel on proper usage of the equipment. It is the sole recommended that all users of MATRIX Fitness Systems exercise equipment be informed of the following information prior to its use. PROPER USAGE 1. Do not use any equipment in any way other than designed of intended by the manufacturer. It is imperative the sole recommended that all users of MATRIX Fitness Systems exercise equipment be informed MATRIX Fitness Systems equipment is used properly to avoid injury. 2. Keep hands and feet clear at all times from moving parts to avoid injury. CHECK FOR DAMAGE PARTS 1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by your country’s local MATRIX Fitness Systems dealer. 2. MANINTAIN LABELS AND NAMEPLATES: DO NOT remove labels for any reason. They contain important information. If un- readable or missing, contact your MATRIX Fitness Systems dealer for a replacement. 3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking of tipping over. A licensed contractor must be performed this, where application. 4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping your liability to a minimum. Equipment needs to be inspected at regular intervals. 5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so. MATRIX Fitness System dealers will provide service and maintenance training at our corporate facility upon request.
Matrix Fitness Systems Corp. 1610 Landmark Drive Cottage Grove WI 53527
Toll Free 866.693.4863 www.matrixfitness.com Fax [phone]
G3-S33 Diverging Lat Pulldown
UNPACKING G3-S33 Diverging Lat Pulldown
Thank you for purchasing a MATRIX Fitness product. Carefully unpack the unit from this box and dispose of the packing
materials in accordance with your local laws.
CAUTION
The weight of the G3-S33 Diverging Lat Pulldown 293lbs. (133kg) not including the weight stack. To avoid injury to
yourself and prevent damage to the frame components, be sure to have proper assistance removing the frame pieces
from this box.
Step 1
G3-S33 Diverging Lat Pulldown
Step 3
TOOLS NEEDED
DESCRIPTION SKETCH QUANTITY
3MM L-Shaped Allen Wrench 1
4MM L-Shaped Allen Wrench 1
5MM L-Shaped Allen Wrench 1
6MM L-Shaped Allen Wrench 1
8MM L-Shaped Allen Wrench 1
10MM L-Shaped Allen Wrench 1
Phillips Screwdriver 1
8MM Open-End Wrench 1
17MM Open-End Wrench 1
Guide Rod Lubrication 1
Hardware Bag
If any items are missing please contact your country's local Matrix dealer for assistance.
Accessory Detail
Step 2
Item Description Sketch Qty
PART # MH0204528B
Weight Stack Detail
Upholstry Detail
Item
K05 Stop Ring 2
K06 Srew (M4x10) 2
Description Sketch Qty
Item
Z02 Screw (M10x25L) 3
Description Sketch Qty
B53 Rubber Shield Spacer 6
B54 Rubber Tip Weight Shield Bolt 6
K06
K05
B54
B54
B53
B53
B54
B53
B53
B54
B54
B53
B54
B53
WEIGHT SHIELD
WEIGHT PLATE
Z02