Max DPG200 User manual

31/08/16
Rotate the base
180° on both
Latch and the
Button.
IMPORTANT:
Be careful not
to disturb inner
components.
RIGHT
GATE
LEFT
GATE
Undo
screws
Mark Latch position on
the side of fence post.
Set template point on
pencil line. Mark all holes
on both sides of post.
Drill two Ø16mm spindle holes.
Drill all other holes to Ø3mm.
Make sure they’re square & level.
70
16
16
16
START
CENTERLINE
OF LATCH
3/4"
SPINDLE
THRU
HOLE
GATE
FRAME
3/4"
FIG. 1
Spindle
12mm
Screw
30mm
Screw
Cut 11-13mm
Longer than Gate Post
Spindle Tube
MUST be fitted
Spindle Tube to be
11 to 13mm longer
than Gate Post
Spindle
INSIDE
LATCH
OUTSIDE
LATCH
CENTERLINE
OF LATCH
3/4"
SPINDLE
THRU
HOLE
GATE
FRAME
3/4"
FIG. 1
Spindle
12mm
Screw
30mm
Screw
Cut 11-13mm
Longer than Gate Post
Spindle Tube
MUST be fitted
Spindle Tube to be
11 to 13mm longer
than Gate Post
Spindle
INSIDE
LATCH
OUTSIDE
LATCH
CENTERLINE
OF LATCH
3/4"
SPINDLE
THRU
HOLE
GATE
FRAME
3/4"
FIG. 1
Spindle
12mm Screw
30mm
Screw
Cut 11-13mm
Longer than Gate Post
Spindle Tube
MUST be fitted
Spindle Tube to be
11 to 13mm longer
than Gate Post
Spindle
INSIDE LATCH
OUTSIDE LATCH
CENTERLINE
OF LATCH
3/4"
SPINDLE
THRU
HOLE
GATE
FRAME
3/4"
FIG. 1
Spindle
12mm Screw
30mm
Screw
Cut 11-13mm
Longer than Gate Post
Spindle Tube
MUST be fitted
Spindle Tube to be
11 to 13mm longer
than Gate Post
Spindle
INSIDE LATCH
OUTSIDE LATCH
180°
View from inside the Property
Make these changes for
Left-Hand Gates.
70
16
16
16
FENCE
Viewed from
inside the Property
Left or
Right?
The Latch comes ready
for Right-Handed gates. A
few simple steps and the
Latch is ready for
Left-Handed gates.
CENTERLINE
OF LATCH
3/4"
SPINDLE
THRU
HOLE
GATE
FRAME
3/4"
FIG. 1
12mm Screw
30mm
Screw
Trim Spindle Tube 11-13mm
Longer than Gate Post
Spindle Tube
MUST be fitted
Spindle Tube to be
11 to 13mm longer
than Gate Post
Spindle
INSIDE LATCH
OUTSIDE LATCH
GRAVITY
Latch
Two-Way
Access
- Suits 50 - 125mm Posts
- Lock-unlock either side
- Lock-down mode –
won’t open
without key
DPG200
GRAVITY
Latch
Two-Way
Access
- Suits 50 - 125mm Posts
- Lock-unlock either side
- Lock-down mode –
won’t open
without key
DPG200
GRAVITY
Latch
Two-Way
Access
- Suits 50 - 125mm Posts
- Lock-unlock either side
- Lock-down mode –
won’t open
without key
DPG200

Use one screw to hold Button body on
fence post.
Trim plastic tubes to match post depth
and insert.
Check both sides are unlocked. Hold the
Latch in place and test the Button works
the Latch.
All good? Completely mount Latch and
Button.
Not working? See Troubleshooting below.
Sit Striker in Latch and mark the Striker’s
centre on gate. Drill pilot holes and mount.
Test the locking and unlocking of the Latch
and Button.
Protrudes
7mm
Protrudes
13mm
13mm
7mm
Maintenance
• Inspect Latch annually or more frequently if the gate is used often.
• Only lubricate with powdered graphite lubricant. No petroleum-based lubricants, oils etc.
• Keep Latch free of contaminants
TROUBLESHO OT ING
If it doesn’t lock, rotate Lock Spindle 180°.
1. Remove keys.
2. Remove Latch off post.
3. Hold the Key, rotate Lock Spindle 180°.
4. Remount Latch, careful not to turn Lock
or Spindle.
Continued
CENTERLINE
OF LATCH
3/4"
SPINDLE
THRU
HOLE
GATE
FRAME
3/4"
FIG. 1
Spindle
12mm
Screw
30mm
Screw
Cut 11-13mm
Longer than Gate Post
Spindle Tube
MUST be fitted
Spindle Tube to be
11 to 13mm longer
than Gate Post
Spindle
INSIDE
LATCH
OUTSIDE
LATCH
CENTERLINE
OF LATCH
3/4"
SPINDLE
THRU
HOLE
GATE
FRAME
3/4"
FIG. 1
Spindle
12mm
Screw
30mm
Screw
Cut 11-13mm
Longer than Gate Post
Spindle Tube
MUST be fitted
Spindle Tube to be
11 to 13mm longer
than Gate Post
Spindle
INSIDE
LATCH
OUTSIDE
LATCH
To protect the
Latch from slam
damage add a
Gate Stop.
Lock
Spindle
Button
Spindle
Trim Spindles
CENTERLINE
OF LATCH
3/4"
SPINDLE
THRU
HOLE
GATE
FRAME
3/4"
FIG. 1
Spindle
12mm Screw
30mm
Screw
Cut 11-13mm
Longer than Gate Post
Spindle Tube
MUST be fitted
Spindle Tube to be
11 to 13mm longer
than Gate Post
Spindle
INSIDE LATCH
OUTSIDE LATCH
Button
POST (mm) TRIM MARK
50 2
75 4
90 5
100 6
125 no trim
Trim both Spindles using the trim
marks.
2456
CENTERLINE
OF LATCH
3/4"
SPINDLE
THRU
HOLE
GATE
FRAME
3/4"
FIG. 1
Spindle
12mm
Screw
30mm
Screw
Cut 11-13mm
Longer than Gate Post
Spindle Tube
MUST be fitted
Spindle Tube to be
11 to 13mm longer
than Gate Post
Spindle
INSIDE
LATCH
OUTSIDE
LATCH
2456
70
16
16
16

33
37
50 to 125
25
57 25
140
52
140
32
5
8
75
19
8
51
5
70 89
43
33
37
50 to 125
25
57 25
140
52
140
32
5
8
75
19
8
51
5
70 89
43

Note: Swimming pool gates, fences and their hardware systems are designed to aid and not subs tute for adult supervision. To
the extent this product is used around a pool, prior to installing, consult local licensing and safety authori es for approvals and/
or requirements. The Keystone® will operate properly only if installed in accordance with instruc ons.
Maintenance: The Keystone® latches should be inspected annually, or more frequently if the gate is used o en. Use a non-toxic
lubricant on all moving parts. Use mild soap & water to clean exterior body or unit. Always remove key upon locking.
Occasionally re ghten all moun ng screws to assure proper opera ons. Please make sure product is adjusted properly per
originally supplied instruc ons.
WARRANTY
MANUFACTURER’S
NATIONWIDE INDUSTRIES Tampa, Florida 33619 USA
Keystone® Series Latches
What Does This Warranty
Cover? This warranty covers
materials and workmanship
as well as any loss of
func onality in your new
Keystone®, with the
excep ons stated below.
What Will Na onwide Do?
In the event of any defect in
material or workmanship or
loss of func onality in the
product coveredunder this
warranty, manufacturer will
replace such Keystone® with
a new Keystone® (or, in the
event the Keystone® is no
longer available, a latch
similar thereto) at no charge.
How Does State Law Apply?
This warranty gives you
specifi c legal rights, and you
may also have other rights
which vary from state to
state.
How Long Does the
Coverage Last? This warranty
to the original purchaser (end
user) runs for the dura on
of one million cycles of use.
Na onwide Industries assumes
this is a true life me of use on
residen al applica ons, and
for commercial applica ons
will use an es mate of usage
based on each applica on.
How Do You Get Service?
In the event of any defect in
material or workmanship, or
failure in the Keystone® latch
covered under this warranty,
return the product, please
return the Keystone® postage
paid, together with proof of
purchase and a brief wri en
descrip on of the problem to
Na onwide Industries, 10333
Windhorst Road, Tampa,
Florida 33619, A en on:
Customer Service Manager.
What Does This Warranty Not Cover? This warranty is void
in its en rety in the event the Keystone® is tampered with,
altered, misused, eglected, damaged, improperly installed
or maintained, repaired or a empted to be repaired by an
unauthorized person, or used in any manner which is not in
accordance with the instruc ons provided by manufacturer.
Manufacturer’s aggregate liability in damages or otherwise
shall not exceed the payment, if any, received by manufacturer
for the Keystone® furnished to you which is the subject of
a claim or dispute. In no event shall manufacturer be liable,
whether in contract, in tort, under warranty, in negligence or
otherwise for incidental, consequen al, or special damages of
any kind whatsoever, howsoever caused.
DISCLAIMER: A pool owner or operator is always responsible
for the safety of those in or around the pool and, to the extent
this product is used around a pool, the manufacturer and sup-
plier of this device cannot and will not accept such responsibil-
ity. In addi on, the manufacturer and supplier of this device
cannot and will not accept responsibility for unauthorized
modifi ca ons to or for defec ve or inadequate maintenance
of this device. No modifi ca on to this device whatsoever is to
be made other than with respect to the adjustments outlined
in the installa on instruc ons. If this device fails to func on
properly, it should be returned promptly to the supplier for
replacement.
Eff ec ve for products sold a er 1/1/15.
Million Cycle Warranty and Liability Limitation