Medela Solo User manual

Solo™
Single electric breast pump
Instructions for use
EN


AR
싱글 전동 유축기
사용 설명서
KO


HE

 HE
93-64
한국어 KO
34–63
 AR
123-94
ENGLISH EN
4–33

4
1. Important safety information
Please read all instructions before using this product.
Keep these instructions for future reference.
Warnings identify all instructions that are important for safety.
Failure to observe these instructions can lead to personal injury or damage to the product.
The following symbols and signal words show the significance of the warnings:
WARNING Can lead to serious injury or death.
CAUTION Can lead to minor injury.
Can lead to material damage
(not related to personal injury).
NOTICE
Useful or important information
that is not related to safety.
i Information
When using electrical products, especially when children are present, basic safety precautions must always be
followed.
WARNING
To avoid fire, electric shock, or serious burns:
• Only use the power adaptor and cable that comes with the device. An inadequate power source or cable may
result in a fire hazard, electric shock or malfunction of the device.
• Prior to use, always inspect the power adaptor and the cable for damage. If damage is found, immediately
discontinue use and call Medela Customer Service.
• Never operate the device if it has a damaged cord or plug, if it is not working properly, if it has been dropped or
damaged, or dropped into water.
• Do not use an electrical product that has been exposed to water or other liquids including:– Do not use while
bathing or showering.– Never place or drop into water or other liquids.
– Do not run water over the pump unit.
– If an electrical product has been exposed to water or other liquids, do not touch, unplug the device from
electrical outlet, turn off and contact the manufacturer.

5
WARNING
To avoid health risks and reduce the risk of severe injury:
• This is a single-user product. Use by more than one person may present a health risk and voids the warranty.
• Do not use the device while operating a moving vehicle.
• Do not continue pumping for more than two consecutive pumping sessions if no milk is expressed.
• Pumping can induce labour. Do not pump until after giving birth. If you become pregnant while breastfeeding or
breast pumping, consult with a licensed healthcare professional before continuing.
• If infected with Hepatitis B, Hepatitis C, or Human Immunodeficiency Virus (HIV), pumping breast milk will not
reduce or remove the risk of transmitting the virus to your baby through your breast milk.
• Wash all parts that come into contact with your breast and breast milk after every use.
• The tubing poses a risk of strangulation when being played with and small parts may be swallowed by toddlers.
Close supervision is necessary when the breast pump or accessories are used in the vicinity of children.
CAUTION
To avoid fire or burns:
• Make sure the voltage of the power adaptor is compatible with the power source. See chapter 17 for technical
specifications.
• Always unplug electrical products immediately after use except for when charging.
• Do not place or store the product where it can fall or be pulled into a tub or sink.
• The device and its accessories are not heat-resistant. Keep away from heated surfaces or open flames.
• Do not use near flammable materials.

6
CAUTION
To avoid health risks and reduce the risk of injury:
• Before each use visually inspect the individual components for cracks, chips, tears, discoloration or
deterioration. In the event that damage to the device is observed, please discontinue use until the parts
have been replaced.
• This product cannot be serviced or repaired. Do not repair yourself. Do not modify the device.
• Never use a damaged device. Replace defective or worn parts.
• Use the device only for its intended purpose as described in these instructions for use.
• Do not use the device while sleeping or overly drowsy.
• If tubing becomes mouldy, discontinue use and replace tubing.
• Do not microwave or boil breast milk. Microwaving can cause severe burns to baby’s mouth from hot spots
that develop in the milk during microwaving (Microwaving can also change the composition of breast milk).
• Clean and sanitize all parts that come into contact with your breast and breast milk prior to first use.
• Only use Medela recommended parts with the device.
• If pumping is uncomfortable or causing pain, turn the unit off, break the seal between the breast and the
breast shield with your finger and remove the breast shield from your breast.
• While some discomfort may be felt when first using a breast pump, using a breast pump should not cause
pain. If you are unsure about correct breast shield sizing please visit www.medela.com or MedelaBreast-
Shields.com (U.S.) or see a lactation consultant/breastfeeding specialist who can help you get a proper fit.
• Contact your healthcare professional or breastfeeding specialist if you can express only minimal or no milk
or if expression is painful.
• If pumping at high altitudes, including in an airplane, consider pumping more often or longer if you feel
there is milk remaining in your breasts after your pumping session.
NOTICE
Take appropriate care in handling bottles and components:
• Plastic bottles and parts become brittle when frozen and may break when dropped.
• Bottles and parts may become damaged if mishandled (e.g., dropped, over-tightened, or knocked over).
• Do not use the breast milk from bottles or components that show signs of damage.

7
Contents
1. Important safety information .....................................................................................................................................................................4
2. Intended purpose.............................................................................................................................................................................................8
2.1 Indications for use....................................................................................................................................................................................8
2.2 Contraindications....................................................................................................................................................................................8
3. Product description.........................................................................................................................................................................................8
3.1 Description of the Solo breast pump ...............................................................................................................................................8
3.2 Your breast pump includes ..................................................................................................................................................................9
4. Getting started..................................................................................................................................................................................................9
4.1 Cleaning before first use.......................................................................................................................................................................9
4.2 Charging the battery........................................................................................................................................................................... 10
5. Cleaning ............................................................................................................................................................................................................ 10
5.1 Cleaning overview ................................................................................................................................................................................11
5.2 Disassembling........................................................................................................................................................................................ 12
5.3 Washing.................................................................................................................................................................................................... 12
5.4 Sanitizing.................................................................................................................................................................................................. 14
5.5 Cleaning the pump unit...................................................................................................................................................................... 15
5.6 Cleaning the tubing............................................................................................................................................................................. 15
6. Assembling the breast pump................................................................................................................................................................... 16
6.1 Selecting the correct breast shield size........................................................................................................................................ 16
6.2 Assembling the pump set ...................................................................................................................................................................17
6.3 Preparing for pumping....................................................................................................................................................................... 18
7. Operating the breast pump ..................................................................................................................................................................... 19
7.1 Mimicking the baby´s rhythm (2-Phase Expression® technology).................................................................................... 19
7.2 Buttons and status light....................................................................................................................................................................... 19
7.3 Expressing your breast milk...............................................................................................................................................................20
7.4 Pausing...................................................................................................................................................................................................... 21
7.5 Turning off ................................................................................................................................................................................................ 21
8. Finding your Maximum Comfort Vacuum™.....................................................................................................................................22
9. Handling of breast milk..............................................................................................................................................................................22
9.1 General storage guidelines..............................................................................................................................................................22
9.2 Freezing..................................................................................................................................................................................................... 23
9.3 Thawing....................................................................................................................................................................................................23
9.4 Feeding breast milk..............................................................................................................................................................................23
10. Maintenance and care.............................................................................................................................................................................24
10.1 Power adaptor care .......................................................................................................................................................................... 24
10.2 Battery maintenance ........................................................................................................................................................................ 24
10.3 Long-term storage.............................................................................................................................................................................25
11. Troubleshooting...........................................................................................................................................................................................25
12. Ordering information...............................................................................................................................................................................26
13. Warranty ........................................................................................................................................................................................................ 27
14. Disposal........................................................................................................................................................................................................... 27
15. Meaning of symbols ..................................................................................................................................................................................28
16. International regulations........................................................................................................................................................................30
16.1 Electromagnetic compatibility (EMC).........................................................................................................................................30
17. Technical specifications............................................................................................................................................................................33

8
2. Intended purpose
2.1 Indications for use
The Solo is a powered breast pump to be used by lactating women to express and collect milk from their breasts.
The Solo breast pump is intended for a single user.
The breast pump is intended to be used in a home environment.
2.2 Contraindications
There are no known contraindications for the Solo breast pump.
3. Product description
3.1 Description of the Solo breast pump
The Solo is a personal-use electric breast pump that includes 2-Phase Expression®technology and is designed for
single pumping. It consists of a pump unit, a pump set (breast shield, connector and bottle) and a tubing.
Pump unit Tubing Pump set
solo
Only the parts of the pump set come into contact with the breast or milk. The pump unit generates an intermittent
vacuum. For milk expression, the tubing conveys the resulting air flow via a membrane, which separates the milk
from the pulsing air, to the breast.
Mode of operation: Continuous
The operating life of the Solo breast pump is 275 hours.
Breast pump model number
101042734
The model number (REF) can be found near the UPC code on the
package your breast pump came in.
101042734

9
3.2 Your breast pump includes
.
4. Getting started
4.1 Cleaning before first use
It is important to do the following before using the breast pump for the first time:
1. Remove the protective cover from the breast shield.
2. Disassemble and clean all parts (except for the tubing) according to the cleaning instructions – see sections
5.2,5.3 and 5.4.
1x Pump unit
(Applied Part)
1x PersonalFit Flex™
breast shield M (24 mm)
(Applied Part)
1x Bottle
1x Membrane
1x Connector body
1x PersonalFit Flex™ connector
1x power adaptor with cable
1x Bottle stand
1x Lid
solo
1x Tubing
Round end piece of tubing
(connects to the connector)
End piece with polygonal
shape (connects to the
pump unit)
For ordering information about accessories see chapter 12.
All pictures shown in these instructions are for illustration purpose only. The actual product may vary due to local
differences or product enhancement.
Medela reserves the right to substitute any component or accessory with a replacement of equivalent perfor-
mance.

10
4.2 Charging the battery
Charge the battery for two hours.
solo
1. Connect the power
cable to the pump
unit.
2. Plug the power
cable into the
power adaptor.
3. Plug the power
adaptor into a wall
outlet.
ÆDuring charging, the
status light is pulsing in
green color.
ÆWhen charging is
complete, it lights up
steadily in green color.
For status light functions in
operating mode see section
7.2.
i Information
• You can use your breast pump while charging the battery. However, it will charge in a slower mode when the
pump is running.
5. Cleaning
It is important you do the following before using your breast pump for the first time: Disassemble all parts & clean
using your breast pump cleaning instructions.
For additional cleaning guidelines see the Center for Disease Control website: https://www.cdc.gov/healthywa-
ter/hygiene/healthychildcare/infantfeeding/breastpump.html (U.S).
Supplies needed:
• Mild dish soap
• Clean wash basin
• Drinking-quality water
• Clean pot for boiling water
Parts to wash or sanitize:
• Breast shield
• Bottle
• Lid
• Connector body
• Membrane
CAUTION
Separate and wash all parts that are exposed to breast milk immediately after use. This will help to remove breast
milk residue and prevent growth of bacteria.
• Wash hands thoroughly with soap and water.
• Only use drinking-quality tap water or bottled water for cleaning.
• Do not place pump parts directly in the sink to rinse or wash. Use a clean wash basin used only for infant feeding items.
• Do not use a dish towel to rub or pat items dry.
• Do not use disinfectants for cleaning.

11
NOTICE
To prevent damage to the tubing.
• Do not clean the tubing with the Quick Clean™ Micro-Steam™ bags in the microwave. Follow the instructions in
section 5.6.
NOTICE
Pay attention to the following:
• Take care not to damage parts of the pump set during cleaning.
• Store the dried pump set in a clean bag/container until next use.
• Do not store wet or damp parts as mould may develop.
• If you notice a white residue on your pump set parts after boiling, your water may have a high mineral content.
Remove residue by wiping parts with a clean towel and allow to air dry.
• Distilled water is recommended when boiling parts to prevent substantial mineral build-up over time, which may
compromise your parts.
5.1 Cleaning overview
Washing and sanitizing are two different activities. They must be done separately to protect you and your baby
from harm, and to maintain the performance of the device.
Wash – To clean the surfaces of the parts by physically removing contamination.
Sanitize – To kill microorganisms, such as fungi, bacteria or viruses, that may be present on the surfaces of the
parts.
When to clean
Breast shield Connector body
and membrane
Bottle & lid
Before first use
Disassemble the parts according to section 5.2
Wash the parts according to section 5.3
Sanitize the parts according to section 5.4
After each use Disassemble the parts according to section 5.2
Wash the parts according to section 5.3
Once per day Disassemble the parts according to section 5.2
Sanitize the disassembled, washed parts according to section 5.4

12
When to clean
Tubing Pump unit
As needed
Normally, cleaning of the tubing is not
necessary.
Refer to section 5.6.
Wipe with clean, damp towel.
Refer to section 5.5.
5.2 Disassembling
Before first use
Remove and dispose of
the protective cover*
from the breast shield.
After each use
Disassemble the pump
set into its individual
parts (breast shield,
connector and bottle) as
follows:
1. Remove the breast
shield from the
connector.
2. Open the connector
lid by squeezing
both flaps and
swiveling the lid
upwards.
3. Remove the
membrane from the
connector body.
4. Separate the bottles,
lids and bottle
stands.
5.3 Washing
Washing is important for hygiene and serves to clean the surfaces of the parts by physically removing contamina-
tion. Wash the parts either by hand or in a dishwasher.
solo

13
Rinse and wash by hand
Wash in dishwasher
or
Do not place the parts directly in the kitchen sink for
rinsing and washing. Use a dedicated wash basin for
infant feeding items.
1. Rinse the disassembled parts, except for the
tubing, with cold, clear drinking-quality water
(approx. 68°F/20°C).
2. Clean these parts with plenty of warm, soapy
water (approx. 86°F/30°C). Use a commercially
available dish soap, preferably without artificial
fragrances and coloring (pH neutral).
3. Rinse the parts with cold, clear drinking-quality
water for 10 to 15 seconds (approx. 68°F/ 20°C).
4. Allow to dry after washing.
1. Place the disassembled parts, except for the
tubing, on the top rack or in the cutlery section. Use
a commercially available dishwashing detergent.
2. Allow to dry after washing.
i Information
If using the dishwasher, parts may become discolored.
This will not impact the part function.
Do not routinely wash the tubing.
See section 5.6 for more details.
Drying
1. Allow to air-dry on a clean, unused dish towel or
paper towel.
Before first use and after each use

14
or Sanitize in microwave
Sanitize on stovetop
10 min
5.4 Sanitizing
Sanitizing is important for hygiene and serves to kill microorganisms, such as fungi, bacteria or viruses. Boil the
parts either on the stovetop or use Quick Clean™ Micro-Steam™ microwave bags.
Before first use and once per day
1. Cover the disassembled, washed parts, except for
the tubing (do not sanitize the tubing), with water
and boil at least for 10 minutes.
2. Allow water to cool and gently remove parts from
water with tongs.
3. Allow to dry after sanitizing.
1. Use Quick Clean™ Micro-Steam™* bags in the
microwave in accordance with the instructions on
the bags. Do not sanitize the tubing.
2. Allow to dry after sanitizing.
* Refer to local website/shops for availability in your
country.
Drying
1. Allow to air-dry on a clean, unused dish towel or
paper towel.
2. Put the clean and dry parts in a clean storage bag
or a clean environment.
Do not store parts in an airtight container/bag if
moist. It is important that all residual moisture dries.

15
5.5 Cleaning the pump unit
Supplies needed:
• Drinking-quality water
• Mild dish soap
• Clean dish or paper towel
Parts needed:
• Pump unit
CAUTION
• Unplug the pump unit before cleaning it.
• Do not immerse the pump unit in water; do not run water over the pump unit.
• Do not spray or pour liquid directly onto the pump unit.
1. Turn the breast pump off.
2. Unplug the pump unit from the power source.
3. Wipe the pump unit with a clean towel moistened
with soapy water.
4. Wipe the pump unit dry with a clean, dry towel.
5.6 Cleaning the tubing
Since the tubing only conveys an air flow (it has no contact with milk), normally cleaning of the tubing is not
necessary.
i Information
Inspect the tubing. If you find condensation in the air tube, wash and dry it immediately or replace the tubing. If
you see breast milk inside the tubing or tubing connector do not attempt to wash, clean or sterilize the tubing.
Instead contact the manufacturer.
Supplies needed:
• Drinking-quality water
• Mild dish soap
Parts needed:
• Tubing

16
Washing the tubing
1. Turn the device off.
2. Remove the tubing from the pump unit.
3. Remove the tubing from the connector lid.
4. Rinse the tubing by pouring cool water into the tubing end until it
flows out of the other tubing end.
5. Wash the tubing in warm, soapy water.
6. Rinse the tubing with clear water.
Drying the tubing
NOTICE
• Do not use the device with wet tubing; doing so will damage it.
1. Shake out any water droplets.
2. Hang the tubing to air dry.
3. Make sure that the tubing is completely dry before using it.
6. Assembling the breast pump
Only use clean and dry parts for assembly. Refer to chapter 5 for cleaning.
6.1 Selecting the correct breast shield size
Measure
nipple diameter
(Ømm)
Breast shield size
(Ømm)
Up to 17 Up to 20 Up to 23 Up to 26
21 24 27 30
Nipple base
Areola
Nipple
measure
1. For proper sizing, measure the diameter of your nipple.
2. Select the breast shield that is slightly larger than your nipple.
For more information on breast shield sizing, visit www.medela.com.

17
6.2 Assembling the pump set
Parts needed:
• Pump set
• Breast shield
• Connector body
• Membrane
• Bottle
• Pump unit
• Tubing
CAUTION
To prevent contamination of your milk:
• Wash hands thoroughly with soap and water before touching the pump unit,
parts of the pump set and breasts.
• Dry your hands with a fresh towel or a single-use paper towel.
• Avoid touching the inside of bottles and lids.
To make sure that your breast pump works properly and safely:
• Check pump set components for wear or damage before use. Replace if
necessary.
• Always inspect all parts prior to use for cleanliness. If dirty, clean according to
chapter 5.
• Only use genuine Medela parts. See chapter 12 for details.
NOTICE
To prevent damage to the breast pump all components must be completely dry before use.
1. Carefully insert the yellow
membrane with the flap into
the opening of the
connector body.
ÆMake sure that the
membrane forms a seal
around the edge of the
connector body.
2. Close the
connector lid until
it audibly clicks.
3. Screw the
connector onto
the bottle.
4. Carefully push
the breast shield
into the
connector.

18
NOTICE
=
solo
It is important to use only PersonalFit Flex™ connectors
and Solo™ tubing with your breast pump. The connector creates a closed
system designed to prevent milk back up. Please ensure that all parts are
completely dry before use. Incompatible or wet components may cause
irreversible damage to your breast pump.
5. The oval breast shields can be
rotated (360°) and placed in
the desired position to have
the most comfortable fit for
you.
6. Insert the round end piece of the
tubing into the opening of the
connector lid (1). Do not attempt
to force it to the stop. It is normal
that there remains a gap (2)
between the collar of the tubing
end piece and the lid.
7. Connect the end piece with
polygonal shape to the pump
unit. Insert the tubing as far as
it will go.
6.3 Preparing for pumping
1. Assemble the pump set as
described in section 6.2.
ÆCorrectly assembled system
for pumping.
2. Place the breast shield on the
breast so that the nipple is
properly centerd in the tunnel.
3. Hold the breast shield and
connector onto your breast
with your thumb and index
finger.
4. Support your breast with the
palm of your hand.
5. Start pumping as described in
section 7.3.

19
7. Operating the breast pump
7.1 Mimicking the baby´s rhythm (2-Phase Expression®technology)
Babies use a “two-speed” sucking action. At first, they suck quickly, and then they switch to a slower,
deeper sucking rhythm once milk starts to flow. The quicker sucking action stimulates the milk ejection
reflex and triggers the milk flow; the slower sucking draws the milk out for the feeding phase.
The pump mimics the baby´s natural sucking rhythm by using a “two-speed” pumping action, the so called
“2-Phase Expression®technology”.
The breast pump begins with a fast sucking action called the stimulation phase. When you see milk flow
or feel milk ejection, you can then press the “Let-down” button to switch to the expression phase, which is
slower than the previous one. If you do not press the Let-down button, the expression phase will
automatically start after the pump has been running for one minute in the stimulation phase.
7.2 Buttons and status light
Decrease
vacuum button
Let-down button
(switches between stimulation
and expression phase)
Increase
vacuum button
On/Pause/Off button
solo
Status light Mode of pump
Light is off Pump is off
Light is flashing Pump is on, stimulation phase
Lights up steadily Pump is on, expression phase
Light is pulsing Pump is on, paused
When the pump is on, the status light appears in different
colors according to the charging state of the battery:
Battery level
Good
Low, approximately 10 minutes left
Very low, charge the battery immediately

20
7.3 Expressing your breast milk
CAUTION
In case of pain or insufficient milk expression:
• Do not hold the pump set by the bottle. This can lead to compression and blockage of the milk ducts and
engorgement.
• Do not try to express with vacuum that is too high and uncomfortable (painful). The pain, along with potential
breast and nipple trauma, may decrease milk output.
• Contact your healthcare professional or breastfeeding specialist if you can express only minimal or no milk or if
expression is painful.
NOTICE
Make sure that the tubing is not kinked or pinched while pumping.
1. If not already done, connect your assembled pump set to the tubing port on the
right of the pump unit.
2. Make sure that the pump set is connected and positioned properly.
3. Press the On/Pause/Off button to start pumping.
ÆThe stimulation phase begins and the status light is flashing.
4. Adjust the vacuum with the Increase vacuum and Decrease vacuum buttons to find a comfortable
level.
5. As soon as your milk begins to flow, press the Let-down button to go to the expression phase.
ÆThe expression phase begins and the status light is on steadily.
ÆIf the Let-down button is not pressed within one minute, your breast pump will automatically go to
expression phase.
6. Adjust the vacuum with the Increase vacuum and Decrease vacuum buttons to find your Maximum
Comfort Vacuum™ (for Maximum Comfort Vacuum™ see chapter 8).
7. When your pumping session is over, press the On/Pause/Off button to stop the pumping operation.
ÆThe breast pump stops automatically after 30 minutes if there is no user interaction with the pump.