MegaLite DECO Cove Q18 User manual

USER MANUAL
Table of Contents
Safety Information 3
What Is Included 3
Specifications 4
Main Power Connection 5
DMX-512 Control 5
Deco Driver Info 5
Size & Weight 6
Cleaning & Maintenance 7
Rigging the Fixture 7
Warranty 8
Customer Support 8

3
What is Included
1pc Deco CoveQ18
6pc Screws
6pc Rubber Washers
1pc Jumper Connector
1pc Lead Cable Connection
1pc User Manual
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
2. Do Not install the unit to close too a heat source.
3. Make sure cables are properly secured away from movement.
4. Maximum surface operating temperature is 125°F
5. Unit must not be left on for long periods of time.
Protection Against Electrical Fire
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This fixture must not be left on for long periods of time.
Protection Against Mechanical Hazards
1. Use safety measures when hanging unit.
2. Use quality bolts when positioning unit.
3. Do not bend more than 160 degrees.
Protection Against Fire
Protection Against Electrical Fire
Protection Against Mechanical Hazards
Check that the unit has not been damaged during transportCheck that the unit has not been damaged during transport

4
Specifications
Part Numbers
Fixture
5059– Deco CoveQ18
Mechanical Specifications
Fastening System: 10 Mounting Holes
Power Connection: 6 Inch 5 Conductor Cable
Housing: FR-4 Aluminum PCB
Lens Angle: 120°
Housing Curving : Limited Curving of 160 degree
Connection: Female Pin Head 2.0 5P
Size: 40 inch (101.6 cm) long,
Cuttable: Cuttable every 3.92” inch (99.7mm)
LED Spacing: .63” inch (16.2mm)
Electrical Specifications
LED Type: SMD 5050 R,G,B,WW
Color Temp WW: 3000K
LED Qty: 60
Power Input: 24V
Total Max Power: 18W
Drive Method: Constant Voltage

5
Main Power Connection
Important Information!
1. Deco Lighting fixtures are specifically designed to be used with a Deco Drivers.
2. Maximum Cable distance of 100ft before voltage drop. (voltage drop will cause intensity drop)
3. Max Power 20W output driver 1 unit per output
4. Max Power 96W output driver 5 units per output
5. All fixtures connected together must be same type (do not connect Variable White or Single
Color fixtures in the same output)
6. Must use 22 AWG cable or thicker to connect the fixture and fixture to fixture.
The occupation of the connection-cable is as follows:
DMX-512 Control
COM Voltage + Black Cable
RRed Red Cable
GGreen Green Cable
BBlue Blue Cable
WWarm White White Cable
When using the Deco Cove Q18 with Deco Drivers the fixture is intended to be used in Ch4 or Ch7 modes. The Deco
Driver will be required to be set in Ch4 or Ch7 operating modes
Ch7 Mode
Dimmer
Red
Green
Blue
Warm White
Strobe
Macro
Ch4 Mode
Red
Green
Blue
Warm White
5
Deco Driver Info
Power Link 20W Output Driver Can connect 1 unit per output port
96W Output Driver Can connect 5 unit per output port
Ch Mode Ch 4 or Ch7 Use Ch4 or Ch7 Mode to control the unit

6
Size & Weight
Fixture Size 40" (1016mm) X .59” (15mm) X .27” (7mm)
Fixture Packaged 41" X 2" X .5"
Net Weight .1lb
Gross Weight .15lb
.59”
15mm
3.93”
100mm
Whole Size
.12”
3.2mm
.64”
16.4mm
40”
1016mm
.27”
7mm

Cleaning and Maintenance
Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installation and
electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots.
3) The power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments. Further
instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety
problems have to be removed.
4) Deco Cove must only be cleaned using dry towel.
7
Rigging the Fixture
Caution!
1. The installation must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning the safety do not install.
3. Unit is to be 24inches away from flammable materials (decoration material)
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experi-
ence including but not limited to calculating working loads, material being used and periodic safety inspections. If you
lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the Fixture has
got to be built in the way that it can hold 10 times the weight for 1 hour with out any failures. Installation should be
checked at least one time a year by a skilled person.
Accessories
5059ACCJUM (Jumper Cable) (1 Included) 5059ACCLEA (Lead Cable) (1 Included)
CONCOLDC5 (5PIN IP rated connection)

8

Mega Lite
18668 Highway 16N
Helotes, Texas 78023
Ph 210-684-2600 Fax [phone]
www.mega.lighting / [e-mail]
Customer Support
Mega Lite has a customer support line to provide set up help and to answer any question should you encounter a prob-
lem. Please visit our website for any other related technical documents. For service related issue please contact our
service dept.
Monday—Friday 9am to 6pm CST
Voice: 210-684-2600
E-mail: [e-mail]
Document
Version Date Fixture Software Notes
1.1 04/09/2021 N/A
Manual Version
Please Visit www.mega.lighting for the most up to date manual version