MegaLite baby color Q70 IR User manual

USER MANUAL
Table of Contents
Safety Information…………………………………………………...…2
Specifications…………………………………………………………..3
Main Power Connection…………………………………………….. 4
DMX-512 Connection……………………………………………...... 4
Main Control Menu.........................................................................5
IR Controller Settings……………………………………………….....7
DMX Profile.................................................................................... 8
Rigging the Fixture……………………………...……………………..9
Cleaning & Maintenance.................................................................9
Parts List.........................................................................................9
Warranty ……………………………………………………………….10

Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
3. Replace fuse only with the specified type and rating.
4. Do Not install the unit to close to a heat source.
5. Make sure cable are properly secured
6. Maximum surface operating temperature 80º.
Protection Against Fire
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This unit must be earthed. (electronically grounded)
4. Do not expose unit to rain or moisture.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.
3

Specifications
4
4039– Baby Color Q70 IR
Mechanical Specifications
Fixture Packaged
Size: 8.12” x 4.3” x 7.8
Weight: 5lb
Size: 10” x 9.5” x 5.75
Weight: 7lb
Electrical Specifications
DMX 512 Protocol
DMX Modes: Mode 1 3 Channels R,G,B,
Mode 2 4 Channels R,G,B,W
Mode 3 7 Channels R,G,B,W, Strobe, Macro, Dimmer
Control Options: Audio Trigger, Main and Remote Function, Infrared Controller (included)
Control & Programming
DMX Connectors: 5 pin XLR connectors in and out
Thermal: Maximum ambient temperature 104°
Maximum surface temperature 140°
Fastening System: Double Mounting Yoke
Display: LED
Power connection: Power Con (type) In & Out
LED Quantity: 7LED Angle: 16°
Diffusion Beam Angel: 27°
Red: 7Power Input Voltage: 110V-240 50/60 Hz
Green: 7
Blue:7Ballast: Electronic auto switching
White: 7
Power Consumption Watts: 49
Amps: .65
PF: .61
LED Watts: 10
LED White CCT: 7702K
Lumens: 2988lm Clear
2648lm With Diffusion
CRI: 78 (all emitters on)
Part Numbers
4.30”
7.8”
8.12”
4.8”

5
Main Power Connection
Caution!
1. Do not connect fixture to a dimmer system.
2. This unit has Auto switching power supply. It will respond to 100V or 240V automatically
3. This unit must be earthed. (electronically grounded)
4. Replace fuse only with the specified type and rating. (when possible)
5. Do not leave fixture on for long periods of time.
The occupation of the connection-cable is as follows:
This fixture is equipped with an electronic power supply that will let the unit operate from 100V to 240V from 50Hz/60Hz
Cable (USA) Cable (EU) Pin 110V
Black Brown
White
Green
Light Blue
Yellow/Green
Live
Neutral
Ground
L
N
220V
L
L
DMX-512 Connection
The fixture is equipped with 5 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only use a
shielded twisted pair cable designed for RS-485 and 5 pin XLR plugs and connectors in order to connect the controller
with the fixture or the fixture with another.
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a 120 Ohm re-
sistor between the (-) and the (+) signal into a 5 pin XLR plug and plug it in to the last fixture on the
signal run. Pre-manufactured terminator plugs are available for purchase from your Mega-Lite
dealer (PDMX-T).
1
5
3
5
3
1
DMX—Input DMX—Output
1. Shield
2. Signal (-)
3. Signal (+)
4
22
4
4. Not Used
5. Not Used

DMX Address
Press Enter to select the DMX start channel use the up/down keys, display will be flashing once you have selected
the desired start channel Press Enter to confirm display will stop flashing.
DMX Ad- Red Dimmer Green Dimmer Blue Dimmer Fade DMX Mode
1-512 0-255 0-255 0-255 0-15
Strobe
0-15
DMX Mode
This function allows you to select the mode in witch
you want to control the fixture. Press Enter use the
up/down keys to select desired DMX mode settings.
Press Enter to confirm the settings.
4 CH
7 CH
Red, Green, Blue, White
Red, Green, Blue, White, Strobe, Macro, Dimmer
White Dimmer
0-255
Display Menu
3 CH Red, Green, Blue
3-Ch
4-Ch
7-Ch
Color Chase
0-15
6
The control board on the fixture base is your interface to access and
control all the functions on the unit. Its digital display gives you a code
view of the options and functions. The following will explain each func-
tion and its options.
Dimmer Mode
59r
Lin
Scur
159r
Menu Up Down Enter
CONTROL BOARD
Red Dimmer
This function allows you to dim up or down the red LED’s . Press Enter use the up/down keys to select desired dimmer
settings. Press Enter to confirm the settings.
Green Dimmer
This function allows you to dim up or down the green LED’s . Press Enter use the up/down keys to select desired dim-
mer settings. Press Enter to confirm the settings.
Blue Dimmer
This function allows you to dim up or down the blue LED’s . Press Enter use the up/down keys to select desired dimmer
settings. Press Enter to confirm the settings.

Fade Scroll
This function allows you to fade the LED’s from one color to another. Press Enter use the up/down keys to select de-
sired fade speed settings from 0 to 15. Press Enter to confirm the settings.
Flash
This function allows you to strobe all the LED’s. Press Enter use the up/down keys to select desired strobe speed set-
tings from 0 to 15. Press Enter to confirm the settings.
White Dimmer
This function allows you to dim up or down the white LED’s . Press Enter use the up/down keys to select desired dim-
mer settings. Press Enter to confirm the settings.
Audio Sensitive Chase
This function allows you to chase the colors from one to another by sensing the audio bass triggers in the area. Press
Enter use the up/down keys to select desired fade speed settings from 0 to 15, 1 will be the fastest fade times and 15
the slowest. Press Enter to confirm the settings.
7
Dimmer Fade Time
This function allows you to set the fade time. Press Enter use the up/down keys to select desired fade time
SCUR– Square Law Fade time
159r-
59r-
Linear– Linear fade time
Press Enter to confirm the settings.
Menu Up Down Enter
CONTROL BOARD
DMX Indicator
When DMX Signal is being received the last point on the control board display will turn on. If
there is no DMX signal present is will be off.

8
RGBW
FLASH
STROBE
ON
OFF
www.mega.lighting
DIM
DIM
FADE
SMOOTH
IR Controller
Baby Color Q70 IR is equipped with a IR Controller that can set lighting
commands via hand controller. The Control must face the front of the
fixture were the LEDs are located. IR controller can be used with the
diffusion cover.
DIM
ON
OFF
DIM
= Turns Fixture On
=Turns Fixture Off
= 4 Values of Dimming up
= 4 Values of Dimming down
=Flash Effect (color must be
selected)
=4 Values of Strobe (color
must be selected)
=Fade between color func-
tion
=Smooth Shutter engage
FLASH
STROBE
FADE
SMOOTH

9
DMX Profile
Baby Color Q70 3 Channel Mode
DMX Chanel Function Description Value
1LED Color Red LED intensity 0-255
2LED Color Green LED Intensity 0-255
3LED Color Blue LED Intensity 0-255
Baby Color Q70 4 Channel Mode
DMX Chanel Function Description Value
1LED Color Red LED intensity 0-255
2LED Color Green LED Intensity 0-255
3LED Color Blue LED Intensity 0-255
4LED Color White LED Intensity 0-255
Baby Color Q70 7 Channel Mode
DMX Chanel Function Description Value
1LED Color Red LED intensity 0-255
2LED Color Green LED Intensity 0-255
3LED Color Blue LED Intensity 0-255
4LED Color White LED Intensity 0-255
5Strobe Strobe (slow to fast) 0-196
Random Strobe (slow to fast) 197-255
No Function 0-1
Color fade (slow to fast) 2-19
Color Snap (slow to fast) 20-39
Random (slow to fast) 40-59
Yellow 60-79
Purple 80-99
6Macro Aqua 100-119
Orange 120-139
Red Pulse 140-159
green Pulse 160-179
Blue Pulse 180-199
Yellow Pulse 200-219
Aqua Pulse 220-229
White Pulse 230-249
White LED Full 250-255
7Dimmer Dimmer Off to Full 0-255

10
Cleaning and Maintenance
Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and
electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any
safety problems have to be removed.
Note: There is no serviceable parts inside the device.. Maintenance and service operations are to be carried out by au-
thorized dealers.
Replacing the fuse: Only replace the fuse with the same type and rating.
Replacing the power cable: If the power cable of this device becomes damaged, it has to be replaced by authorized
dealers or trained professional only.
Should you have further questions , please contact your dealer.
Parts List
4039-PCB-MAI-DIS Main & Display PCB card
4039-POW Power Supply
4039-PCB-DRI Driver PCB
4035-DIF Removable Diffusion Filter
4035-FAN Replacement fan
Rigging the Fixture
Caution!
1. The installations must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning the safety do not install.
3. Unit is to be 24inches away from flammable materials (decoration material)
4. Use high quality installation equipment to hang unit.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experi-
ence including but not limited to calculating working loads, material being used and periodic safety inspections. If you
lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the fixture has
got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be
checked at least one time a year by a skilled person.
4035-BAR Barndoor Accessory
4035-KNO Knob Set

Mega Lite
18668 Highway 16N
Helotes, Texas 78023
Ph 210-684-2600 Fax [phone]
www.mega.lighting / [e-mail]
Customer Support
Mega Lite has a customer support line to provide set up help and to answer any question should you encounter a prob-
lem. Please visit our website for any other related technical documents. For service related issue please contact our
service dept.
Monday—Friday 9am to 6pm CST
Voice: 210-684-2600
E-mail: [e-mail]
Document
Version Date Fixture Software Notes
1.1 03/08/2023 N/A
Manual Version
Please Visit www.mega.lighting for the most up to date manual version