MegaLite DECO Driver CV4 User manual

USER MANUAL
Table of Contents
Safety Information 3
What Is Included 3
Specifications 4
Main Power Connection 5
DMX-512 Connection 5
Output Connection 6
Control Board 7
DMX Profile 8
Size & Weight 9
Cleaning & Maintenance 10
Parts List 10
Warranty 11
Customer Support 11

Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
2. Do Not install the unit too close to a heat source.
3. Make sure cables are properly secured away from movement.
4. Maximum surface operating temperature is 135°F
5. Unit must not be left on for long periods of time.
Protection Against Electrical Dangers
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This unit must be earthed. (electronically grounded)
4. Do not expose unit to rain or moisture.
5. The Unit must be installed in a well ventilated area.
6. Be sure ventilation slots are not blocked.
Protection Against Mechanical Hazards
1. Unit surface may reach high temperature. Allow about 5 minutes after powering the unit before
moving.
2. When repositioning rack ears make sure they are securely attached.
3
What is Included
1pc Deco Driver CV4
1pc Power Con Cable
4pc 5 Pin Screw Terminal Blocks
1pc User Manual

4
Specifications
Part Numbers
Fixture
5060– Deco Driver CV4
Mechanical Specifications
Fastening System: Removable rack ears for Wall Mounting , Rack mounting and Rear rack mount-
ing
Display: Digital
Power Connection: PowerCon (type) Cable Mounted to Edison head.
Housing: Black painted
DMX Connection: 5 Pin XLR & RJ45 in and out (optional 3 pin available)
Output Connection: 4 Port 5 pin Screw terminal & RJ45 output
Electrical Specifications
Power Input:
Outputs:
Power Per Output
Total Max Power:
Ballast:
Output:
Drive Method:
110-240VAC 5.9A 50/60 Hz
4
96W
4x 96W
Electronic: Mean Well RSP-500-24
24V
Constant Voltage
Protocol: DMX 512
DMX 5 Modes:
1 Channel Mode Dimmer
2 Channel Mode Warm White, Cool White
3 Channel Mode R, G, B
4 Channel Mode R, G, B, W
7 Channel Mode Dimmer R, G, B, W, Strobe, Macro
Operating Mode: 22 Pre Programs, Stand alone via display
Control & Programming

5
Main Power Connection
Caution!
1. Do not connect fixture to a dimmer system.
2. This unit has Auto switching power supply. It will respond to 110V or 220V automatically
3. This unit must be earthed. (electronically grounded)
4. Replace fuse only with the specified type and rating.
The occupation of the connection-cable is as follows:
DMX-512 Connection
The fixture is equipped with 5 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only use a
shielded twisted pair cable designed for RS-485 and 3 pin XLR plugs and connectors in order to connect the controller
with the fixture or the fixture with another.
DMX 5 Pin —Input DMX 5 Pin—Output
1. Ground
2. Signal (-)
3. Signal (+)
1
3
2
4
55
4
3
2
1
This fixture is equipped with an electronic power supply that will let the unit operate from 100V to 240V from 50Hz to 60Hz
Cable (USA) Cable (EU) Pin 110V
Black Brown
White
Green
Light Blue
Yellow/Green
Live
Neutral
Ground
L
N
220V
L
L
RJ45 8 Pin— In & Output
1. Signal (+)
2. Signal (-)
7&8. Ground
1 Signal +
2 Signal -
3 N/A
4 N/A
5 N/A
6 N/A
7 Ground
8 Ground

6
Output Connection
Deco Driver CV4 is designed to be used as a driver for Constant Voltage lighting fixtures. There are many fixtures a
Deco Driver can control . Each of the 4 output can be individually controlled and addressed to use the same or different
fixture per each output. The Deco Lighting fixture manual will give you the information with power link limitations and
control type for that unit.
Fixtures that require Strip Cable connection will connect the input cables via 5Pin Screw terminal
4 Ch Fixtures
DMX Control Mode
4 or 7CH
3 Ch Fixtures
DMX Control Mode
3 CH
2 Ch Fixtures
DMX Control Mode
2 CH
1 Ch Fixtures
DMX Control Mode
1 CH
Fixtures that require RJ45 connection will connect the input cables RJ45 Output
Pin1 Red-
Pin 2 24V+
Pin 3 Green-
Pin 4 24V+
Pin 5 Blue-
Pin 6 24V+
Pin 7 Warm White-
Pin 8 24V+
4 Ch Fixtures
DMX Control Mode
4 or 7CH
Pin1 Red-
Pin 2 24V+
Pin 3 Green-
Pin 4 24V+
Pin 5 Blue-
Pin 6 24V+
Pin 7 N/A
Pin 8 N/A
3 Ch Fixtures
DMX Control Mode
3 CH
Pin1 Warm White-
Pin 2 24V+
Pin 3 Warm White-
Pin 4 24V+
Pin 5 Cool White-
Pin 6 24V+
Pin 7 Cool White-
Pin 8 24V+
2 Ch Fixtures
DMX Control Mode
2 CH
Pin1 White-
Pin 2 24V+
Pin 3 White-
Pin 4 24V+
Pin 5 White-
Pin 6 24V+
Pin 7 White-
Pin 8 24V+
1 Ch Fixtures
DMX Control Mode
1 CH

7
Control Board
System Mode
( DMX)
Port Mode DMX Address
(01) (01) (001)
DMX: DMX mode allows you to set the DMX
operational mode: For each output port you can
select Mode of operation and DMX start address.
Press Enter use the Up / Down button to select
the output port press Enter once selected. Mode
function will then be highlighted, use the Up /
Down button to select your operating mode.
Each lighting fixture will have a different operat-
ing mode. Consult the fixture’s manual or fixture
label to determine the operating mode. Press
Enter, DMX Address will then be highlighted,
use the Up / Down button to select the fixtures
start address. Start address should match your
controller’s start address channel. Press Enter
to confirm your settings.
Port Mode DMX Address
(02) (01) (001)
Port Mode DMX Address
(03) (04) (004)
Port Mode DMX Address
(04) (07) (210)
System Mode
( Auto)
Prog 01
(ST Color 1)
Auto: Auto mode allows you to access the
pre-built auto function for control. Press Enter
use the Up / Down button to select the pre pro-
gram fixture look. Programs 01 to 18 are single
scene programs and programs 19 to 21 are
chase programs. Press Enter once you have
decided on the scene or chase. For Programs 1-
18 use the Up/Down buttons to adjust fixture
dimmer output. For programs 19-21 use the Up/
Down buttons to adjust the chase speed. Press
Enter to confirm the fixture setting.
Prog 18
(ST Color 18)
Prog 19
(Step Chace)
Prog 20
(Color Fade)
“ “
Prog 21
(Strobe)
Prog 22
(Chasing)
Prog 01 Dimmer
(000)
Prog 18 Dimmer
(000)
Prog 19 Speed
(000)
Prog 20 Speed
(000)
“ “
Prog 22 Speed
(000)
Prog 22 Speed
(000)
System Mode
( Manual)
Red
(000)
Green
(000)
Blue
(000)
White
(000)
Manual: Manual mode allows you to man-
ually control the intensity of all 4 ports simultane-
ously via the control display without the need for
a DMX controller. Press Enter to select the dim-
mer output you would like to adjust . Use the Up/
Down keys to select the dimmer intensity. There
is many Deco Fixtures that can be controlled via
a Deco Driver. Please Consult your Deco Light-
ing fixtures Manual to see what values are ac-
tive. Press Enter to confirm the setting.
Lock Display: The display for the Deco Driver factory setting is lock screen function to unlock the display press and hold
the Menu & Enter for 3 seconds

8
DMX Profile
Deco CV4 1 Channel Mode
DMX Channel Function Description Value Init
1Dimmer LED Intensity 0-255 255
Deco CV4 2 Channel Mode
DMX Channel Function Description Value Init
1LED Color Warm White LED Intensity 0-255 255
2LED Color Cool White LED Intensity 0-255 255
Deco CV4 3 Channel Mode
DMX Channel Function Description Value Init
1LED Color Red LED Intensity 0-255 255
2LED Color Green LED Intensity 0-255 255
3LED Color Blue LED Intensity 0-255 255
Deco CV4 4 Channel Mode
DMX Channel Function Description Value Init
1LED Color Red LED Intensity (all outputs) 0-255 255
2LED Color Green LED Intensity (all outputs) 0-255 255
3LED Color Blue LED Intensity (all outputs) 0-255 255
4LED Color White LED Intensity (all outputs) 0-255 255
Deco CV4 7 Channel Mode
DMX Channel Function Description Value Init
1Dimmer Dimmer 0 to 100% 0-255 255
2LED Color Red LED Intensity (all outputs) 0-255 255
3LED Color Green LED Intensity (all outputs) 0-255 255
4LED Color Blue LED Intensity (all outputs) 0-255 255
5LED Color White LED Intensity (all outputs) 0-255 255
No Function 0-1
6Strobe Strobe (slow to fast) 2-127 0
Random Strobe (slow to fast) 128-255
No Function 0-1
7Macro Color Fade (slow to fast) 2-127 0
Color Chase (slow to fast) 128-255

9
Size & Weight
19”
8.25”
17.37”
1.75”
Fixture Size 19" X 8.25" X 1.75"
Fixture Packaged 21.5" X 9.5" X 3.5"
Net Weight 8.5lb
Gross Weight 10.5lb

Cleaning and Maintenance
Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and
electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (rack, suspension, trussing).
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any
safety problems have to be removed.
4) Ventilation ports must be clear of any debris.
5) Inner ventilation power supply fan must be clear of any debris
10
Rigging the Fixture
Caution!
1. The installation must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning the safety do not install.
3. Unit is to be 24inches away from flammable materials (decoration material)
4. Installation location must have adequate air flow.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experi-
ence including but not limited to calculating working loads, material being used and periodic safety inspections. If you
lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the Fixture has
got to be built in the way that it can hold 10 times the weight for 1 hour without any failures. Installation should be
checked at least one time a year by a skilled person.
5060PCBMAI MAIN PCB / DISPLAY
5060PCBDRI DRIVER PCB
5060PCBDMX5 5 PIN DMX PCB
5060PCBDMX3 3 PIN DMX PCB
5060POW POWER SUPPLY
5060FUS F5AL 250V 5X20MM FUSE
5060SWI ON/OFF SWITCH
5060HOURAC REMOVABLE RACK EARS
5060CONSCR 5 PIN SCREW CONNECTION
Parts List

Mega Lite
18668 Highway 16N
Helotes, Texas 78023
Ph 210-684-2600 Fax [phone]
www.mega.lighting / [e-mail]
Warranty Information
Warranty Conditions
-Unless otherwise stated in writing, your product is covered by a one year parts and labor limited warranty.
-LED’s and LAMPS are not guaranteed to match in color temperature or output.
-It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and reseller or distributor.
If purchase date cannot be provided, date of manufacture will be used to determine warranty period.
-Goods returned under warranty must follow the proper authorization procedure and must be accompanied by a copy of
the original invoice.
-Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical
means of shipment.
-Repair or replacement as provided for under this warranty is the exclusive remedy of the consumer. MEGA SYSTEMS
INC. makes no warranties, express or implied, with respect to any product, and Mega Systems specifically disclaims any
warranty of merchantability or fitness for a particular purpose. Mega Systems shall not be liable for any indirect, inci-
dental or consequential damage, including lost profit, sustained or incurred in connection with any product or caused by
product defect or the partial or total failure of any product regardless of the form of action, wether in contract, tort
(including negligence), strict liability or otherwise, and wether or not such damage was foreseen or unforeseen.
-Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or parts. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Customer Support
Mega Lite has a customer support line to provide set up help and to answer any question should you encounter a prob-
lem. Please visit our website for any other related technical documents. For service related issue please contact our
service dept.
Monday—Friday 9am to 6pm CST
Voice: 210-684-2600
E-mail: [e-mail]
Document
Version Date Fixture Software Notes
1.1 10/22/2020 V1.1
Manual Version
Please Visit www.mega.lighting for the most up to date manual version