MegaLite Deco Vintage Scoop Q32 User manual

USER MANUAL
Table of Contents
Safety Information 2
What Is Included 2
Specifications 3
Main Power Connection 4
DMX-512 Control 4
Deco Driver Info 4
Installation 5
Size & Weight 6
Warranty 7
Cleaning & Maintenance 8
Customer Support 8

2
What is Included
1pc Deco Vintage Scoop Q32
1pc User Manual
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
2. Do not install the unit to close too a heat source.
3. Make sure cables are properly secured away from movement.
4. Maximum surface operating temperature is 125°F.
5. Unit must not be left on for long periods of time.
Protection Against Electrical Fire
1. Disconnect power before servicing.
2. For connection to main power supply, proceed to page 4.
3. This fixture must not be left on for long periods of time.
4. This fixture is intended for indoor use, do not install this unit outdoors.
Protection Against Mechanical Hazards
1. Use safety measures when hanging unit.
2. Use quality bolts when positioning unit.
3. Do not open, risk of electrical shock.
Protection Against Fire
Protection Against Electrical Fire
Protection Against Mechanical Hazards
Check that the unit has not been damaged during transportCheck that the unit has not been damaged during transport

3
Specifications
Part Numbers
Fixture
5043- Deco Vintage Scoop Q32 CAS-5043-2—Dual Road Case
Mechanical Specifications
Fastening System: Dual Yoke
Power Connection: Y Cable mounted RJ45 In & Out
Cable Length: 7.2 Feet
Housing Material: Steel
Reflector Angle: 74°
Size:22.75” x 14.5” x 25.98”
Weight: 13lb
Electrical Specifications
LED Type: SMD 5050 R,G,B,WW
Color Temp WW: 2475K
CRI: (Warm White) 74
Lumens @ Full: 1107lm
LED Qty: 140
Each LED Watts: .25
Power Input: 24V DC
Total Max Power: 32W
Drive Method: Constant Voltage (to be used with Deco Drivers)

4
Main Power Connection
DMX-512 Control
When using the Deco Vintage Scoop Q32 with Deco Drivers the fixture is intended to be used in Ch4 or Ch7 modes.
The Deco Driver will be required to be set in Ch4 or Ch7 operating modes.
Ch7 Mode
Dimmer
Red
Green
Blue
Warm White
Strobe
Macro
Ch4 Mode
Red
Green
Blue
Warm White
Deco Driver Info
1 Red
2 V+
3 Green
4 V+
5 Blue
6 V+
7 Warm White
8 V+
Deco Driver
96W Output Driver
3 Fixture Max
per Output
Power Link Deco Drive CV24 Output Driver Can connect 1 per port Max 12 units
96W Deco Output Driver Can connect 3 unit per output port
Ch Mode Ch 4 or Ch7 Use Ch4 or Ch7 Mode to control the unit
Important Information!
1. Deco Lighting fixtures are specifically designed to be used with Deco Drivers.
2. Maximum cable distance of 100ft before voltage drop. (Voltage drop will cause intensity drop)
3. All fixtures connected together must be the same type. (Do not connect Variable White or Sin-
gle Color fixtures in the same output)
4. Must use Cat 6A, 23 AWG or thicker to connect the fixture. (Not included)
Deco Driver CV24
1 Fixture Max
per Output Port
12 units Max per Deco
Drive CV24

5
Installation
Caution!
1. The installation must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning safety do not install.
3. Unit is to be 24 inches away from flammable materials (decoration material)
When installing the fixture it is very important that you follow common safety procedures. Installation requires extensive
experience including but not limited to calculating working loads, material being used and periodic safety inspections. If
you lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
The installation location of the fixture must to be built in the way that it can hold 10 times the weight for 1 hour. Installa-
tion should be checked at least one time every 2 years by a skilled person.
Fixture Size 22.75" (mm) X 14.5” (mm) X 25.98“(mm")
Fixture Packaged 28" X 24" X 16"
Net Weight 13 lb
Gross Weight 19 lb
Size and Weight
21.25”
22.75”14.5”
25.98”
15.39”
10.59”

Mega Lite
18668 Highway 16N
Helotes, Texas 78023
Ph 210-684-2600 Fax [phone]
www.mega.lighting / [e-mail]
Customer Support
Mega Lite has a customer support line to provide set up help and to answer any question should you encounter a prob-
lem. Please visit our website for any other related technical documents. For service related issue please contact our
service dept.
Monday—Friday 9am to 6pm CST
Voice: 210-684-2600
E-mail: [e-mail]
Document
Version Date Fixture Software Notes
1.1 02/08/2023 N/A
Manual Version
Please Visit www.mega.lighting for the most up to date manual version
Cleaning and Maintenance
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation location.
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any
safety problems have to be removed.
4) Fixture must only be cleaned using damp towel.