MELICONI Personal 1+ User manual

Personal 1+
Thank you for choosing a Meliconi remote control.
The Personal 1+ remote control is designed to command a SAMSUNG digital television sets.
Its ergonomic shape and soft rubber body make it easy to grip and protect it from shocks and drops.
By LEARN function, you can capture and store infrared signals from other remotes and match at will to one or more buttons.
The MELICONI remote control reproduces infrared signals corresponding to the original; the functions that operate in radio
frequency (e.g. voice commands and pointers) are not supported.
The remote control has a permanent memory, so it does not lose its settings even if there are no batteries in it.
The remote control requires 2 new 1.5V AAA/LR03 alkaline batteries, not included in the
package. Insert with the correct polarity as shown in figure.
DO NOT use rechargeable batteries.
BATTERIES TEST: Press and hold the 5button and check that the LED remains on
continuously until the button is released. If the light is off or blinks, the inserted batteries are low,
therefore they need replacement.
Do not leave exhausted batteries inserted, as liquid may leak and damage the remote control
INSERTING THE BATTERIES
SAFETY WARNINGS
The remote control and batteries should not be exposed to excessive heat such as sunlight, fire
or the like.
The product is not a toy. Keep out of reach of children or domestic animals.
This remote control, after inserting the batteries, is normally ready for use as it is already set at the
factory with a specific code.
Keep this booklet for future reference
Remote control for TV sets SAMSUNG ready to use

The Personal 1+ remote control is equipped with Learn technology that can acquire and memorise signals from other infrared
remote controls. This feature is particularly useful in several cases.
➢To add or change a function connected to a button on the MELICONI remote control.
Having activated the remote control and checked it is working correctly, you may need to add or replace a function on one
of the MELICONI remote control buttons with another function you consider to be handier or more frequently used.
➢Assign some functions to some buttons to control other devices (example: volume +/- SOUNDBAR).
The Personal 1+ remote control can learn up to a maximum of 10 signals coming from various original remote controls and
connect at will to the desired buttons.
Signals can also be learnt and set on all the buttons on the MELICONI remote control, except the button; obviously the
preset functions are lost, but they can be restored by the REMOTE CONTROL RESET procedure.
The Learn operation can be repeated numerous times, and the signals captured are kept in the memory even if the batteries
are removed or go flat.
●POSITIONING THE REMOTE CONTROLS CORRECTLY.
•Check that the batteries in both remote controls (the original and the MELICONI remote) are
fully charged; if semi-charged batteries are used the signal acquisition procedure may prove
difficult or fail completely.
•Position the original remote control in front of the MELICONI remote control so the areas
which emit the infrared signals are opposite each other at a distance of approximately 2 cm.
•On the MELICONI remote control press and hold the button until the LED lights up;
release.
•Enter the code 0303.
•Within 30 seconds, press and hold down one of the buttons on the original remote control;
the LED on the MELICONI remote control should start flashing; if it doesn't, move the remote
controls closer together.
•Gradually move the original remote control away, making sure the two remotes stay aligned,
until the point at which the LED stops flashing; then move the remote control to half the
previous distance and keep both remotes in this position until the process has terminated.
●CAPTURING SIGNALS.
1. On the MELICONI remote control press and hold the button until the LED lights up;
release.
2. Enter the code 0404.
3. While the LED remains on, press the button on the original remote to be captured, hold it down until the LED goes out
and then release it.
IMPORTANT: If after releasing the button the LED comes back on, press the same button again until the LED goes out
once more.
4. While the LED is flashing, on the MELICONI remote control press the desired button to match the captured function.
5. To capture other signals to connect to other buttons, repeat the procedure from point 3.
6. To end the procedure, hold down the button and wait for three flashes of the LED indicating that the storage has
been completed; release.
Reached the number of records available, the dedicated memory becomes full, preventing further use.
To free memory use one of the following procedures in relation to the data that you want to delete:
• DELETE FUNCTION BY SINGLE BUTTON
• RESET THE REMOTE CONTROL
LEARN FUNCTION
watch
the video

The functions of the buttons on the MELICONI remote control are only available if the original device is equipped with it.
Sometimes some functions of the original remote control are not directly present on the MELICONI remote control keypad.
To enable them, connect to the www.cme.it page, use the on-line tool BUTTONS AND FUNCTIONS and continue until you
see the list matching buttons between the original remote control and the MELICONI remote control.
To obtain some functions, press and hold the button and press the corresponding key indicated in the table.
If the functions you want to play are matched with an number in orange color, operate as follows:
1. On the MELICONI remote control press and hold the button until the LED lights up;
release.
2. Enter the code 0707.
3. While the LED remains on, enter the previously identified number corresponding to the function you
want to play.
4. While the LED flashes, within 30 seconds, on the MELICONI remote control press the desired button to
match the function obtained.
5. Repeat the procedure from point 3 for each function you want to add on MELICONI remote control.
6. To end the procedure, hold down the button and wait for three flashes of the LED indicating that
the storage has been completed; release the button (the used buttons loses their original function that
will be called by setting again the activation code).
If you want to delete the function in combination with a single button, operate as follows:
1. On the MELICONI remote control press and hold the button until the LED lights up;
release.
2. Enter the code 0707.
3. While the LED remains on, enter the code 1600.
4. While the LED flashes, within 30 seconds, on the MELICONI remote control press the button which you want to delete
the function
5. Repeat the procedure from point 3 for each function you want to delete on MELICONI remote control.
6. To end the procedure, hold down the button and wait for three flashes of the LED indicating that the storage has
been completed; release the button (to recall the original functions, setting again the activation code).
If necessary it is possible to completely reset the remote control and bring it back to the initial conditions.
WARNING : All user settings will be lost. Operate as follows:
•On the MELICONI remote control press and hold the button until the LED lights up; release.
•Enter the code 0279.
•Three final flashes indicate that the operation has been completed successfully.
RESET THE REMOTE CONTROL
DELETE FUNCTION BY SINGLE BUTTON
BUTTONS AND FUNCTIONS

●IF THE REMOTE CONTROL IS NEW AND YOU CAN NOT MAKE IT WORK
Check that you have carried out all the settings procedures correctly. If necessary repeat them, following all the steps
indicated carefully, or contact the ASSISTANCE.
●IF THE REMOTE CONTROL IS NO LONGER ABLE TO CONTROL THE DEVICE
Disconnect the device from the electric socket and leave it without power for a few minutes; switch the device on again.
Remove the batteries from the remote control, press the ON/OFF button twice and insert NEW batteries.
Make sure that the remote control is pointing at the device without any obstacles between them.
If necessary try to the RESET THE REMOTE CONTROL.
●IF SOME FUNCTIONS ARE NOT AVAILABLE ON THE REMOTE CONTROL
Sometimes some functions of the original remote control are not directly present on the MELICONI remote control keypad.
To enable them, operate as described in the BUTTONS AND FUNCTIONS chapter.
●HOW TO CHECK IF THE REMOTE CONTROL SENDS INFRARED SIGNALS
The human eye is not able to detect infrared signals; use a camera (even that of the mobile phone).
Aim the infrared LED located in front of the remote control (not the red LED above) and press and hold on the remote control
the 5button.
If you see through the camera, the LED light with short white / light blue flashes means that the remote control works and
emits infrared.
web: www.cme.it e-mail: t[email protected]
IMPORTANT! To obtain technical assistance, it is essential to indicate the BRAND and MODEL of the appliance you intend
to control and the name of the MELICONI remote control you are using.
WARRANTY: 2 year Always keep your sales receipt as proof of the validity of the product’s warranty. The warranty is
voided if the product is tampered with or used improperly.
Meliconi SpA, Via Minghetti 10 - 40057 Cadriano di Granarolo Emilia, (BO) Italy
web: www.meliconi.com email: t[email protected]
The symbol showing a wheelie bin with a cross through it which appears on the device indicates that at the
end of its useful life the product must be collected separately from other waste. Therefore, at the end of the
device’s life, you must take it to appropriate centres for the differentiated collection of electrical and electronic
waste, or return it to the retailer when purchasing a new device of equivalent type. Suitable differentiated
collection to allow subsequent recycling of the decommissioned device, with environmentally-compatible
treatment and disposal, help to prevent any negative effects on the environment and health and to promote
the recycling of the materials of which the device is made.
CAUTION: Batteries must not be disassembled, thrown into fire or released into the environment. Improper
use can cause damage to the environment and health. The symbol of the bins, indicating that the batteries
should be disposed of according to current regulations; inquire on collection of spent batteries and
accumulators in force in your country.
ASSISTANCE
ATTENTION!
Most problems are caused by using insufficiently charged batteries.
We recommend checking and replace them as shown in the INSERTING THE BATTERIES chapter.
TROUBLESHOOTING (F.A.Q.)