Melissa & Doug Victorian Dollhouse User manual

WARNING:
Small parts.
Not for children under 3 years.
CHOKING HAZARD -
!
CAUTION:
Adult assembly required.
!
Melissa & Doug, LLC
All Rights Reserved
www.MelissaAndDoug.com
We care about your comments.
Please call us! 1-800-284-3948
Victorian Dollhouse
Assembly Instructions
ITEM #2580 B

Parts List
Page 2 of 36

1E
Foundation Panel 1D
Foundation Panel 1E
1H
Foundation Panel 1H
1B
Foundation Components
Foundation Panel 1B
1F
Foundation Panel 1F
1G
Foundation Panel 1G
1C
Foundation Panel 1C
1D
1A
Front Steps 1A
Page 3 of 36

2
Floor Panel 2 (1st floor)
Floor Panels
(upper surface views)
11
Floor Panel 11 (2nd floor)
14
Floor Panel 14 (top floor)
Page 4 of 36

4
Wall Panel 4
Outer Wall Panels
(exterior views)
5
Wall Panel 5
7
Wall Panel 7
8
Wall Panel 8
10
Wall Panel 10
6
Wall Panel 6
9
Wall Panel 9
15
Wall Panel 15
Page 5 of 36

3
Wall Panel 3
13
Wall Panel 13
12
Staircase Assembly 12
(1st floor)
16
Staircase Assembly 16
(2nd floor)
28
Screw
29
29
screw hole plug and cover
Inner Wall Panels, Staircases and Assembly Hardware
Page 6 of 36

Roof Panel 23
23
Roof Panel 25
25
Roof Panel 24
24
Roof Panel 22
22
Roof Panel 18
18
Roof Panel 17
17
Roof Panel 27
27
Roof Panel 26
26
19
Roof Panel 19
Roof Panel 20
20
Roof Panel 21
21
Roof Panels
(exterior tiled surface views)
Page 7 of 36

22
21
20
26
27
18
19
25 24
top view
23
front view
5
10
8
15
right view
7 9
1G 1D
14
11
2
13
12
16
3
rear view
1H
isometric front left view
1A 1C
1E 1F
1B
Completed dollhouse views
(with component item numbers)
Page 8 of 36

Step 1: Begin by attaching Front Steps 1A to the painted surface of Foundation Panel 1B using 2 screws (item 28),
as illustrated. Next, with artwork facing out on all the foundation panels, assemble the foundation as shown in the diagram.
Make sure that the screw holes on the long edges of panels 1E and 1H are facing up. Secure the panels together
with 16 screws (item 28).
1G
1C
1B
1A
1D
1E
1F
screw holes
facing up
28
screw holes
facing up
Page 9 of 36

3
2
28
yellow and green tile artwork on this
end of Floor Panel 2
yellow tile artwork on bottom
half of Wall Panel 3
pink with purple tile wall artwork on
upper half of Wall Panel 3
wood floor artwork on
this end of Floor Panel 2
Step 2: Attach Wall Panel 3 to Floor Panel 2 with 2 screws (item 28) inserted through the bottom of Floor Panel 2.
Make sure to orient the artwork on the wall and floor panels as described below.
Page 10 of 36

Step 3: Attach the floor panel assembly from Step 2 to the foundation assembly from Step 1 using
5 screws (item 28), as illustrated.
28
Step 2 assembly
Step 1 assembly
Page 11 of 36

28
Step 4: Attach Wall Panel 4 to Floor Panel 2 with 2 screws (item 28), as illustrated, making sure the
window ornamentation is facing out.
4
2
Page 12 of 36

5
28
Step 5: Attach Wall Panel 5 to Wall Panel 4 and Floor Panel 2 with 3 screws (item 28), as illustrated, making sure the
window ornamentation is facing out.
42
Page 13 of 36

6
Step 6: With the pink clapboard artwork facing out, slide Wall Panel 6 into position and secure with 2 screws
(item 28), as illustrated. Make sure that interior wall artwork on panels 5 and 6 are aligned after assembly.
528
Page 14 of 36

7
28
Step 7: Attach Wall Panel 7 to Floor Panel 2 with 2 screws (item 28), as illustrated, making sure the window
ornamentation is facing out.
2
Page 15 of 36

8
28
Step 8: Attach Wall Panel 8 to Wall Panel 7 and Floor Panel 2 with 3 screws (item 28), as illustrated.
7
2
Page 16 of 36

9
28
Step 9: With the pink clapboard artwork facing out, slide Wall Panel 9 into position and secure with 2 screws (item 28)
to Wall Panel 8, as illustrated. Make sure that the interior wall artwork on panels 9 and 6 (from Step 6) are identical.
8
6
Page 17 of 36

10
28
Step 10: Place the bottom edge of Wall Panel 10 into the slot behind the front steps. Then attach to Floor Panel 2,
Wall Panel 6 and Wall Panel 9 with 6 screws (item 28), as illustrated. The window and door ornamentation should
be facing out, and the exterior and interior wall artwork on wall panels 10, 6 and 9 should be aligned.
6
9
2
Page 18 of 36

11
28
Floor Panel 11 slot
Step 11: Position Floor Panel 11 as shown below. Next, fit the slot in Floor Panel 11 over the inner Wall Panel 3, and
carefully slide it down until the holes on its edges align with the 8 holes in the surrounding Wall Panels 7, 8, 10, 5 and 4.
Secure Floor Panel 11 to the surrounding wall panels with 8 screws (item 28), as illustrated in the top view diagram.
back view of dollhouse
3
11
28
top view of dollhouse
showing all 8 screws
7
8
10
5
4
Page 19 of 36

12
28
opening in Floor Panel 11
3
11
2
bottom edge
top landing
Step 12: Attach Staircase Assembly 12 by sliding it down through the opening in Floor Panel 11, as
illustrated. Place the staircase flat against Wall Panel 3, with the top landing of the staircase resting on Floor
Panel 11 (2nd floor panel) and the bottom edge resting on Floor Panel 2. Secure with 1 screw (item 28)
inserted through the opposite side of Wall Panel 3.
Page 20 of 36