Memphis Shades MEM5806 User manual

Part No. 2350-0200
Wind Management Device - Side Wings
Fits King Size H-DOEM Windshields and
Memphis Fats
Before assembly, read Warnings inside
MEM5806
WARNING
During installation, make sure that the Wing and hard-
ware do not interfere with any cables or wiring when
the forks are turned all the way in either direction. Also
make sure , through the full range of adjustment, that
the Wing and hardware do not hit the gas tank.
1.
2. The improper installation of this product and related
components could result in serious injury or death.
CAUTION
Memphis Shades Wings are made from Lucite
acrylic, and will last for years with proper care. Clean
your Wing with plenty of soapy water (mild dishwashing
liquid is best) and a soft cotton cloth. Use your bare
hands to feel and dislodge bugs, or cover with a wet,
soapy towel and let it soak. Don’t use paper towels and
scrape with anything. Small scratches can be removed
with NOVUS #2.
1.
Never use any glass cleaning products, petroleum
based chemicals, or cleaning agents with ammonia,
bleach or any other harsh chemicals. This includes (but
not limited to) RainX, brake fluid, acetone, paint thinner,
benzene and gasoline. “If it hurts your nose, it will hurt
the plastic.”
2.
Glass cleansing agents will cause severe damage to
your Wing, and will void your warranty.
For care and cleaning we recommend using Memphis
Shades All Kleer, a unique cleaner/polish, bug
remover and rain repellant that leaves a super slick
surface that makes the next cleaning even easier.
3.
Ref Code Description Qty
I5806 Mounting Instructions 1
MEP5806 Side Wings 2
S1240 HW Biplane clamp - nylon 4
M943 Allen wrench, 5/32” 1
A pad 8
B pad 8
Memphis Shades warrants all product components, metal
and plastic, against defects in materials and workmanship
for 24 months.
For Parts and Warranty Help, Contact:
Memphis Shades, Inc.
P.O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or you
can also reach us by email:
[e-mail]
1. Kit Contents
2. Mounting Instructions
REVISION 0




1. Cover gas tank and front fender with towels to avoid
damage during installation.
2. The Side Wings can be mounted in two different positions,
Wide or Narrow (Fig 1)
Narrow Position Mount
3. Use the 5/32” Short arm allen wrench to remove the
Socket head cap screw from the Wing mount part of the
Biplane clamp (Fig 2).
4. Insert the posts on the Wing mount through the
corresponding holes in the Side Wing. The Wing mount
should face the front. Reassemble the Biplane clamp by
fitting and tightening the Socket head cap screw (Fig 3). Do
this for each pair of holes.
5. Repeat on the second Side Wing (Fig 4) Proceed to item 9.
Wide Position Mount
6. Use the 5/32” Short arm allen wrench to remove the
Socket head cap screw from the Wing mount part of the
Biplane clamp (Fig-5a). Remove the gasket from the Center
piece, rotate it 180° and refit.
7. Rotate the Wing mount 180° (Fig 5b) and insert the posts
through the corresponding holes on the Side Wing. The
Wing mount should face the front. Reassemble the Biplane
clamp by fitting and tightening the socket head cap screw
(Fig 6). Do this for each pair of holes
8. Repeat for the second Side Wing (Fig 7)
Continued

Windshield Thickness Guide
B PADS - 1/8” WINDSHIELD
A PADS - 3/16” WINDSHIELD
Use guide to determine which
pads to use. - “A” or “B”
FOLD HERE
EDGE OF WINDSHIELD
EDGE OF WINDSHIELD

2. Mounting Instructions, continued
Fig. 1
Fig. 7
Fig. 4
Narrow
Bi plane clamp set up as
supplied.
Wide
Wing mount on Bi plane
clamp must be rotated 180°
Fig. 2
Fig. 3
Fig. 5a
Fig. 6
Remove this gasket,
rotate 180° and refit
Rotate the
Wing mount
180° and refit
Fig. 5b
Fig. 8
9. Use the “Windshield Thickness Guide” to determine your
windshield thickness, by holding the guide to the edge of your
windshield. Select “A” pads if windshield is 3/16” or
“B” pads if windshield is 1/8”.
10. Use the 5/32” short arm allen wrench to remove the
screw in the wing clamp part of the Biplane clamps. (Fig. 8)
11. Fit your selected pad into Wing clamp and Wing mount by
aligning pads and pressing into place. Repeat for other
Biplane clamp (Fig. 9)
12. Position the Biplane clamps (with Side Wing fitted) over
the existing windshield. Once satisfied with the position,
tighten down the Socket head cap screw to secure the
Biplane clamps in place (Fig 10)
Fig. 9
Fig. 10