Memphis Shades 2321-0085 User manual

2321-0085 SPORTSHIELD MOUNTING KIT YAMAHAVSTAR 650/1100 CUSTOM
MOUNTING INSTRUCTIONS
Glass cleansing agents will cause severe damage
to your windshield, and will void your warranty.
NOTE: At certain times of the day the Sunlight can reflect
off the curvature of a windshield and cause extreme heat
build-up on motorcycle instruments and instrument panel.
Take care when parking. Park facing the sun, place an opaque
object over the instruments or adjust the windshield to avoid
reflections.
IMPORTANT CARE AND CLEANING INSTRUCTIONS
Memphis Shades Windshields and Lowers are made of
Lucite® acrylic, and will last for years with proper care.
Clean your windshield with plenty of soapy water — mild
dishwashing liquid is best — and a soft cotton cloth. Use your
bare hand to feel and dislodge bugs, or cover with a wet soapy
towel and let it soak. Don't use paper towels and don't scrape
with anything. Small scratches can be removed with NOVUS
# 2.
NEVER use any glass cleaning products, petroleum based
chemicals, or cleaning agents with ammonia, bleach or any
other harsh chemicals. This includes (but not limited to)
RainX, brake fluid, acetone, paint thinner, benzene and
gasoline. "If it hurts your nose, it will hurt the plastic."
No additional tools required for this kit.
1. Cover gas tank and front fender with a towel to avoid
damage during installation.
2. Install the windshield mounting plates onto the windshield,
using the bolts that are pre-assembled on the mounting plates.
The Santoprene grommets should be inserted through the
holes in the windshield so that the flat round part of the grom-
met lies flat on each side of the plastic. The tabs point in to-
wards the headlight when installed correctly. (see figure 1 )
3. Loosely install the four Fork Clamps on the forks, approxi-
mately 2" apart. (see figure 2). The Top Fork Clamp must sit
against the Upper Triple Tree (See figure 3)
4. Start with Fork Clamp Bushing adjusted to rear of slot (see
figure 4) Then adjust as needed and check for clearance. (See
warning above.)
5. Slip the windshield mounting plates and windshield onto
the fork clamps, (see figure 5) and secure the left and right
side locking mechanism
6. Adjust the height, angle and alignment of the windshield
and tighten ALL bolts.
Read and follow these directions carefully.
During installation, make sure that the windshield and hard-
ware do not interfere with any cables or wiring when the forks
are turned all the way in either direction. Also make sure,
through the full range of adjustment, that the windshield and
hardware do not hit the tank.
This is a detachable windshield, ALWAYS make sure the
Locking Mechanism is Fully Engaged after installing the
windshield!
The improper installation of this kit and related compo-
nents could result in serious injury or death.
Figure 2
Tabs face in towards
headlight.
Figure 1 Figure 3
WARNING:
"Mounting clamps
backwards will cause
damage to your tank."
Side view. When installed correctly,
Allen bolts are tightened from the
back side of the fork, not the front.
CORRECT
Throttle side,
front of bike
INCORRECT
Throttle side,
front of bike
MEM8934 08-18-08
WARNING
If the adjustable clamps are installed backwards, it will result in
serious gas tank damage. Always check for proper gas tank
clearance before tightening hardware. (see Figure 2)
Loosen Allen Screw to
adjust Bushings to desired
windshield angle.
Figure 4
Note: This is a detachable windshield, ALWAYS make sure
the Locking Mechanism is Fully Engaged after installing
the windshield! (see figure 5)
Top fork
clamp must sit
against the
Upper Triple
Rear of slot

BUSHING ASSEMBLY
A C D
E
F
A. R329
B. R333
C. R323
D. R324
E. R318
F. R331
B
Figure 5
2321-0085 SPORTSHIELD MOUNTING KIT YAMAHAVSTAR 650/1100 CUSTOM
MOUNTING INSTRUCTIONS
MEM8934 08-18-08
CORRECT
Fully engaged
NOT CORRECT
1. Place lower slot into lower bushing. 2. Rotate top slot into
place. 3. & 4. Secure locking Mechanism.
1234
Loosen Allen Bolt to adjust angle, then re-tighten Allen Bolt.
R322C/T
LATCH
ASSEMBLY
1. M532
2. M520
3. M1197
4. M1196
2
3
1
BUSHING
ASSEMBLY
4
MEM8934 SPORTSHIELD KIT
Memphis Shades warrants all product components, metal and plastic,
against defects in materials and workmanship for 24 months.
FOR PARTS AND WARRANTY HELP, CONTACT:
MEMPHIS SHADES
P. O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or
You can also reach us by email:
[email protected]
Part # Description Q’ty
M8934 Mounting Instructions 1
M1199 Left Sportshield Mounting Plate 1
M1198 Right Sportshield Mounting Plate 1
M532 Small Fork Clamp Outer, Detachable 4
M520 Inner Adjustable Fork Clamp Half 4
R318 1” Socket Shoulder Washer 4
R323 Bushing Assembly (2 piece) 4
R324 #207 O Ring, EPDM 4
R329 5/8” Slot Nut 4
R333 1” DIA Spacer, 9/32” Thick 4
R322C Clutch Side Latch Assembly 1
R322T Throttle Side Latch Assembly 1
Part # Description Q’ty
M504 Socket Shoulder Washer 4
M505 Button Nut 4
M543 Santoprene Grommet 4
M310 3/16” Short Arm Allen Wrench 1
M313 3/16” Allen Wrench Cover 1
R331 1/4-20x7/8” SS Socket Head Cap Screw 4
M302 1/4-20x1/2” SS Socket Head Cap Screw 8
R334 6-32x3/8” Flat Head SS Screw 8
R326 SS Spring 2
C