MXAEQ7
7-BAND MARINE GRADE
GRAPHIC EQUALIZER
Memphis Audio built a 50+ year legacy in the audio industry engineering the highest quality products to
produce the best possible listening experience for our fans and loyal supporters. To fully appreciate our
products we recommend taking the time to read and follow the instructions in this manual. As always, we
recommend all installations and service be performed by an authorized Memphis Audio dealer.
For optimal performance, Memphis recommends using only Memphis Connection accessories. Outfitting
your system with properly sized Memphis Connection wire and accessories will dramatically boost your
listening experience and increase the durability of your Memphis Audio products.
Ready to Turn It Up? Read This First! Crossover Control
Set-Up and Adjustment
Features
Specifications
The MXAEQ7 7-band graphic EQ allows you to dial in your system for peak performance. The universal 1/2 din
design will fit easily in multiple applications and serve as the command center for your systems audio. Control
every aspect of your system from one device to lock in precision sound for the best possible audio experience.
This unit is equipped with a conformal coated circuit board and water resistant connections to protect form
damage from water and the elements making it an ideal solution for boat and powersports applications.
• Conformal coated circuit board
• Water resistant sealed connections
• Active gain and pre-amp with input sensitivity
• Volume control with up to 9.75V RMS output
• Individual left and right sensitivity controls for MAIN/AUX
• 7-Band graphic equalizer with 18dB boost cut
• Low noise BI-FET op-amp design yields minimal distortion
• On-board 30V bi-polar switching power supply
• Universal 1/2 DIN chassis for easy, near universal installation
• High grade golden RCA Jack inputs/ Outputs
• Subwoofer level control
• Adjustable subwoofer frequency
• 20dB headroom eliminates signal overload
• MAIN/AUX input selector
• Dual color back-lighting for easy visibility
It is recommended that MID BASS/MIS/HI frequencies be set to a center position and that the SUB frequency be
set around 60Hz. You are able to adjust each band independently to its own exact position but remember that
the proper setting depends on the overall system itself and your own specific musical taste so you may need to
find your own personal sweet spot for maximum enjoyment.
PRIOR TO TURN ON
Turn the volume on the unit to minimum.
Adjust the input gains to minimum.
Turn the source unit volume to minimum.
Set EQ controls to flat (12 o’clock)
SYSTEM TURN ON
After completing all the wiring and signal connections you can turn the system on.
ADJUSTMENT
Raise the volume of the unit to MAX.
Adjust left and right input gains of the unit until they are half way between MIN/MAX.
Gradually increase the source volume until clipping occurs.
Begin gradually increasing input gains until the distortion is audible then backdown slightly
NOTE the system should be extremely loud at this time.
Turn the volume control down to minimum and back up to a comfortable level.
Volume changes should sound linear and balanced.
Front Panel Controls
1. GAIN CONTROL - Adjusts the ouput level
2. FADER CONTROL - Adjusts the volume between front and rear speakers in a 4-speaker system.
3. INPUT SELECTOR SWITCH - selects the MAIN/AUX input
4. SUBWOOFER LEVEL - Controls the subwoofer level
5. EQUALIZER CONTROLS - Controls the frequency response of the boost or cut with the 7 band controls - 50Hz,
125Hz, 315Hz, 750Hz, 2.2KHz, 6KHz, 12KHz
7-BAND GRAPHIC
BOOST/CUT
BANDWIDTH
S/N RATIO
FREQUENCY RESPONSE
MAX OUTPUT VOLTAGE
THD%
INPUT SENSITIVITY
HEADROOM
INPUT IMPEDANCE
STEREO SEPARATION
OPERATING VOLTAGE
OUTPUT IMPEDANCE
50Hz, 125Hz, 315Hz, 750Hz, 2.2KHz, 6kHz, 16kHz
18dB
Specific to each band. Hi Shelving
110dB REF 1V Input
10Hz-50KHz, +/-1dB
9.75V RMS
0.05%
Adjustable 200 mV - 3.5V RMS
20dB
20K Ohms
80dB/1KHz
11-15V Negative Ground
1KΩ
41 2 3 5
VOLUME SUB LEVEL FADER MAIN AUX 50Hz 125Hz 315Hz 750Hz 2KHz 6KHz 12KHz
