Memphis MXAZEQ5BT User manual

65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
MXAZEQ5BT
Dual Zone 5-Band Marine EQ
with Bluetooth
DESIGNED AND DEVELOPED IN THE UNITED STATES, MEMPHIS, TENNESSEE, SINCE 1965
800.489.2300
www.memphisaudio.com
122 Gayoso Ave.
Memphis,TN, USA @MEMPHISCARAUDIOUSA
@MEMPHISAUDIO
D
E
S
I
G
N
E
D
A
N
D
D
E
V
E
L
O
P
E
D
I
N
T
H
E
U
S
A
|
M
E
M
P
H
I
S
,
T
N
,
U
N
I
T
E
D
S
T
A
T
E
S
,
S
I
N
C
E
1
9
6
5
|
D
E
S
I
G
N
E
D
A
N
D
D
E
V
E
L
O
P
E
D
I
N
T
H
E
U
S
A
|
M
E
M
P
H
I
S
,
T
N
,
U
N
I
T
E
D
S
T
A
T
E
S
,
S
I
N
C
E
1
9
6
5
|
D
E
S
I
G
N
E
D
A
N
D
D
E
V
E
L
O
P
E
D
I
N
T
H
E
U
S
A
|
M
E
M
P
H
I
S
,
T
N
,
U
N
I
T
E
D
S
T
A
T
E
S
,
S
I
N
C
E
1
9
6
5
|

65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
Memphis Audio built a 50+ year legacy in the audio industry engineering the highest quality products to produce
the best possible listening experience for our fans and loyal supporters. To fully appreciate our products we
recommend taking the time to read and follow the instructions in this manual. As always, we recommend all
installations and service be performed by an authorized Memphis Audio dealer.
For optimal performance, Memphis recommends using only Memphis Connection accessories. Outfitting
your system with properly sized Memphis Connection wire and accessories will dramatically boost your
listening experience and increase the durability of your Memphis Audio products.
Ready to Turn It Up? Read This First!
Memphis Audio recommends all installations to be performed by an authorized Memphis Audio dealer. If you
chose to proceed with your own installation, please read the following instructions.
• Turn OFF all stereo and other electrical devices prior to beginning the installation
• Disconnect the negative {-} battery lead from your systems battery.
• Locate all fuel lines, brake lines, oil lines and electrical cables when mapping out your installation.
• Check the mounting depth to make sure there is sufficient room to mount the EQ
• When connecting ground points, make certain that all paint is carefully scrapped away from the grounding
location and that the contact is made with bare metal.
• Use a utility knife to trim away fabric from hole locations prior to drilling or cutting. Drilling directly into
fabric can tear and damage fabric beyond the desired installation location.
• When running power cables through sheet metal, be certain to use grommets to insulate the lines from the
metal edges of the sheet metal.
• If possible, use tubing through the grommets for extra protection.
There are two basic mounting options for your MXAZEQ5BT. One is to under-mount the unit beneath the dash
panel using the supplied brackets as shown.
The second option is to flush mount the unit by cutting a hole through a suitable panel for an built-in look. If
you chose the in-dash mounting method, be careful to cut the correct size hole for the best appearance. Also
take care not to let your EQ or the cables interfere with other components in the mounting location.
Installation Instructions
Features
Mounting The Equalizer
Specifications
The MXAZEQ5BT 5-Band marine grade EQ with Bluetooth allows you to dial in your system for peak performance and
control cabin, tower and sub levels from a single unit. The universal 1/2 din design will fit easily in multiple
applications and serve as the command center for your systems audio. This unit is a perfect solution for marine
audio applications.
Main Volume Control With Three Independent Zone Output Controls
Connect up to 3 external amplifiers with separate level output controls from the front panel with a
master volume control for the entire system.
Front Panel Source Selector MAIN/AUX and BLUETOOTH
The front panel source selector control knob allows you to switch between 3 different input sources
(BLUETOOTH, AUX and RCA INPUTS)
5-Band Dual Equalization - Bass, Mid-Bass, Mid and High (BOAT and TOWER)
Each center frequency receives 18dB of boost or cut to adjust
• Bass (75Hz) • Mid Bass (250Hz) • Mids (2kHz) • Mid/High (6kHz) • High (14.5kHz)
USB Charging Port
2 Amp output to charge your connected Bluetooth device.
High Voltage Line Driver
6V of pre-amp signal voltage to deliver clean output signal for your amplifiers. Up to 6V in BLUETOOTH
mode and up to 10V in AUX/MAIN mode.
MOSFET PWM Power Supply
The Pulse Width Modulated power supply is used to provide steady voltage from the vehicles or boats
charging system which can vary under normal operating conditions
Marine Grade Conformal Coated PCB
Conformal coated circuit board resists damage and corrosion from the elements and water.
MXAZEQ5BT
Dual Zone 5-Band Marine EQ
with Bluetooth & Sub Level
Washer
Spring Washer
Washer
Tapping Screw
Spring Washer
Screw
Frequency Response: 10Hz - 50kHz
Frequency EQ Center: 75Hz, 250Hz, 2kHz, 6kHz, 14.5kHz
Total Harmonic Distortion THD: 0.02%
Signal to Noise Ratio: >101dB
Inputs: Switchable, 3-source MAIN, AUX, Bluetooth
Equalization Boost/Cut: -/+18dB
Channel Separation: 85dB
Maximum Output Voltage: MAIN, AUX - 10Vrms @ 0.1%THD | Bluetooth - 6Vrms @0.1%THD
Power Supply: 11-15V DC negative ground
Fuse: 2 Amp (AGC type included)
Dimensions: Chassis 7”W x 1.0”H x 4” D (178mm x 25.4mm x 102mm)

1. Source Input Control Knob - This control will change the input source from MAIN, AUX and Bluetooth
2. Main Volume Control Knob - This control adjusts the output for BOAT, TOWER and SUB.
3. Boat Output Control Knob - This control adjusts the output of the BOAT zone.
4. Tower Output Control Knob - This control adjusts the output of the TOWER zone.
5. Sub Output Control Knob - This control adjusts the output of the SUB zone.
6. Boat Equalizer Control Knobs - These controls will adjust the output at 75Hz, 250Hz, 2KHz, 6KHz, 14.5Hz
from the BOAT output.
7. Tower Equalizer Control Knob - These controls will adjust the output at 75Hz, 250Hz, 2KHz, 6KHz, 14.5Hz
from the TOWER output. 1. USB Charging - Connect your Bluetooth device to charge the battery
2. AUX Input - Connect this 3.5mm input to any second input source (DVD, etc.) This is selected from the input
source control knob.
3. AUX Output - Connect this 3.5mm output to a second EQ, external amp or soundbar. This is a variable output
controlled from the master volume control knob with no EQ adjustments.
4. POWER CONNECTIONS
RED - 12V DC (Constant) - Connect this lead to a 12 volt (+) positive constant source
BLACK - Ground - Connect this lead to a solid ground point
BLUE- Remote Turn On Input - Connect this lead to the remote output of your head unit's remote turn-on
output. If there is no remote output lead or no head unit, connect this lead to a 12V DC switched power
source. This lead turns the EQ on and off.
5. MAIN RCA Input - Connect this to your head unit’s pre-amp output. This is selected from the input source
control knob.
6. Sub RCA Output - Connect this to your mono amplifier’s RCA input connections.
7. Tower RCA Output - Connect this to your tower amplifier’s RCA input connections. This is controlled from the
tower output control knob. Tower EQ controls (outer control knob) will adjust the tone controls from this
output.
8. Boat RCA Output - Connect this to your boat amplifier’s RCA input connections. This is controlled from the
boat output control knob. Boat equalizer control (inner EQ knobs) will adjust the tone controls from this
output.
Controls Rear Panel Connections
1 2 3
4
74
5 6
1
2
3 4 5 6 7 7

Wiring Configurations Using Main Input Wiring Configuration Using AUX Input
Set SOURCE INPUT Control Knob To MAIN Set SOURCE INPUT Control Knob To AUX
Soundbar
SUB TOWER BOAT
Source Unit
(Blue Wire) Turn-On REMOTE - Connect to Switched 12VDC (Red Wire) To DC + 12V Battery Black Wire To Car Chassis GND
Amplifier Amplifier Amplifier
Soundbar
SUB TOWER BOAT
(Blue Wire) Turn-On REMOTE - Connect to Switched 12VDC (Red Wire) To DC + 12V Battery Black Wire To Car Chassis GND
Amplifier Amplifier Amplifier

Adjust the EQ to match your listening style. You can adjust different aspects of your sound until you reach the
perfect blend to suit your listening style.
Equalization Adjustment
1. Turn the source selector knob to BT (Bluetooth)
2. Open your devices Bluetooth settings. Search for MXAZEQ5BT and pair your device. Once paired you can
stream audio to the MXAZEQ5BT.
3. You can either use the Bluetooth device or the MXAZEQ5BT to change tracks and control the master volume
of your system.
4. There is no visual or audio conformation from the MXAZEQ5BT to indicate your device is paired. You must
confirm this from your Bluetooth device.
5. There is no need to un-pair your device to listen to a different input source. Use the front panel source
selector knob to change MAIN or AUX input.
Each knob is essentially a tone control dedicated to a specific part of the audio spectrum from 20Hz to 20kHz.
They can help your speakers match the environment in which they are being utilized. There are 5 knobs for BOAT
and 5 knob for TOWER that allow you to adjust the EQ setting for each zone separately. Start with all nine
knobs in the 12 o’clock position. Listen to a variety of types of music. Rotate each of the knobs individually.
When rotating the knob you will notice the effect of the knobs on different parts of the audio spectrum. Use
the knobs to dial in your sound to the perfect level.
75Hz: Use this control sparingly. It can produce low bass punch that may force the speakers to reproduce
sounds beyond their capability
250Hz: This controls frequencies above sub bass and below the midrange
2kHz: This range is responsible for musical instruments, vocal and midrange percussion.
6kHz: Controls the frequencies above midrange and below high range
14.5kHz: Controls the upper high range frequencies.
Bluetooth Pairing and Operation
Equalizer Band Ranges
Set SOURCE INPUT Control Knob To BT (Bluetooth)
Wiring Configuration Using Bluetooth Only
Soundbar
SUB TOWER BOAT
(Blue Wire) Turn-On REMOTE - Connect to Switched 12VDC (Red Wire) To DC + 12V Battery Black Wire To Car Chassis GND
Amplifier Amplifier Amplifier

Troubleshooting
PROBLEM
No Sound
Hiss
Distorting Speakers
Amplifier Popping Noise or
Turn-on and Turn-off Thump
SOLUTION
1. Check Power and Remote Turn-on for the proper voltage
2. Check the ground connections
3. Check if the source knob is at the correct selection
1. Turn down the amplifier gains
2. Adjust the source unit output
3. Check for kinked or faulty RCA interconnect cables
1. Adjust the equalization levels
2. Lower the volume of the source unit
3. See your dealer
1. Equalizer battery + must be connected to a constant 12VDC source
2. Check wiring for proper hook up of power and remote leads
Warranty
This products has a one year warranty from the date of purchase for defects in material or workmanship.
The warranty is void if the product has been physically damaged by improper usage or abuse. If repairs are
attempted outside of a Memphis Audio facility, the warranty is void.
This warranty is limited to the original retail purchaser and does not cover any expenses incurred in the
removal or re-installation of the product. This warranty does NOT apply to product exterior and cosmetics.
Memphis Audio disclaims any liability for incidental or consequential damages caused by product defects.
Memphis Audio liability will not exceed the purchase price of the product and the warranty period specified.
Warranty shipments to Memphis Audio are the responsibility of the purchaser. Pack the product carefully in
the original carton if possible Memphis Audio will not be responsible for damages incurred in shipment or
due to improper packaging materials used by the purchaser.
If determined to be within warranty your product will be repaired or replaced at the discretion of Memphis
Audio.
What is NOT covered under warranty
• Damage due to improper installation
• Damage caused by exposure to moisture, excessive heat, chemical cleaners and/or UV radiation
• Damage through negligence, misuse, accident or abuse. (Repeated returns for the same damage may be
abuse)
• Product damaged in accident and/or due to criminal activity
• Service performed by anyone other than Memphis Audio
• Subsequent damage to other components
• Any cost or expense related to the removal or re-installation of product
• Products with tampered, missing , altered or defaced serial numbers/labels
• Freight damage
• The cost of shipping product to Memphis Audio
• Return shipping on non-defective items
• Any product not purchased from an authorized Memphis Audio dealer
Some states do not allow the exclusion or limitation of incidental or consequential damages. The above
limitations or exclusions may not apply to you. This warranty gives you specific rights, you may have other
rights which vary from state to state.
If warranty service is required, a return authorization number is required to return the product to Memphis
Audio.