Mercado Medic REAL Series Assembly instructions

INSTRUCTIONS FOR USE AND CARE
BACKREST
SEAT HEIGHT
December 2013
Item no.
The seat height is adjusted by means of the lever (1), which
releases the gas fix lifting mechanism when pulled upwards.
You can then move the seat down by putting weight on the
seat or up by reducing the weight on the seat (stretch out
your legs).
Once the seat reaches the required height, release the
lever (1).
The chair is equipped with a high Double Medic back recliner.
The depth of this can be adjusted by loosening the two
screws (1) using a 5 mm hex key, for example the Mercado
key. The entire mechanism can then be moved forwards
or backwards. Once adjusted, retighten the two screws.
NOTE! Ensure that the back recliner is not moved too far
out ‘backwards’, i.e. so that the spring button clips stop the
back recliner from being moved too far back.
The angle of the entire back recliner can be adjusted by
loosening the two knobs (2) and then adjusting the back
recliner by taking hold of the back, angling it as required,
and then retightening the knobs (2).
The height of the backrest can be adjusted by loosening the
screws (3) using the Mercado key and then adjusting the
back to the required height. Once adjusted, retighten the
screws (3).
The angle of the backrest can be adjusted by loosening the
handles (4), taking hold of the back, angling it as required,
and then retightening the handles (4).
The REAL chair has replaceable components, accessories and functions
with adjustment options for individual adaptation. The chair must only be
used by the person for whom it was prescribed and for the purpose for
which it is intended. The chair is intended for indoor use only. Thechair
must not be equipped with any accessories or components other than
those approved by Mercado Medic AB. Repairs and other technical
measures may only be carried out by personnel authorised by Mercado
Medic AB. Read these instructions carefully before using the chair for
the first time.
1
3
4
2
1

HANDBRAKE
SEAT TILT
CLEANING, MAINTENANCE AND CHARGING
The chair has a seat tilt function. This adjusts the angle of the
entire seat.
To adjust the angle, loosen the wheel (1) and then turn the
knob (2) clockwise or counterclockwise until the preferred
seat tilt angle has been set. Then retighten the wheel (1).
The brake is controlled by a lever (1). To apply: move the
lever backwards. The brake lever can be installed on either side
of the chair. The chair is equipped with H-base Maintenance
and the brake can also be applied using the foot (2).
NOTE! The brake on the chair must always be applied when
getting in and out of the chair. The brake must be checked
on a regular basis. In case of wear, change the brake rubber.
The braking function may be reduced on uneven surfaces.
The chair must be wiped down and kept free from
dust and dirt:
Remove loose dirt, crumbs and the like. Apply a
thin layer of foam and rub the foam in evenly with a
damp cloth. Wipe with a clean and lightly dampened
cloth. Vacuum clean when dry.
The fix lifting mechanism must be checked regularly
for dust and dirt:
Raise the seat to its highest position. Clean with
a cloth. Do not use any water or solvents. Then
lubricate the cylinder with a thin layer of Teflon or
silicone-based grease. These make less of a mess than
mineral oil-based grease.
Mercado Medic AB Telephone & Fax E-mail & Internet
Tryffelslingan 14 Tel. [phone] E-mail [email protected]
SE-181 57 Lidingö Fax [phone] Internet www.mercado.se
HEADREST
The height of the headrest can be adjusted by loosening the
knobs (1) and then adjusting the height as required. Now
retighten the knobs (1). To adjust the depth of the headrest
cushion, loosen the handle (2), adjust to the required position,
and then retighten the handle (2). To adjust the angle of the
headrest cushion, loosen the handle (3), adjust to the required
angle, and then retighten the handle (3).
2
1
1
2
3
2
1