Mercia Garden Products 01DTSHRAX0705SDNW-V1 User manual



 
















  



2mm Drill bit
x2 


































        






















                










 

















































ANY QUESTIONS?
Scan the QR code to
contact us via our customer
portal.
PLEASE SCAN HERE:


 
8
Some steps within this set of instructions come with an added video guide for your
convenience. These can be accessed via the QR code and used to aid you in constructing that
step. See below for how to use.
You can also nd all the videos on our youtube channel:
https://www.youtube.com/@merciagardenproducts8716/videos
ACCESSING VIDEO GUIDES...
1.Find the QR code within the instruction step...
2. Open camera app...
3. Scan QR code...
4. Watch the video...
On your personal smart device (phone, tablet etc), open your camera app or QR code scanner
app.
To scan the QR code, hold the camera over the QR code so that it can be seen on the screen.
Once the QR code has been registered, follow the prompts on your device to open the video.
(This will vary depending on your device.)
Please note: Ensure to use the back camera of your smart device as this will scan the QR code more
accurately.

The video guide will now be displayed on your smart device.
Parts Needed- No. QTY 1
No. QTY 1
No. QTY 1
Step..... 
Within the instruction step, there will be an icon in the top right that has a QR code in. This
is where the video can be accessed from.
Please note: not every step has a video guide.
Disclaimer: The building constructed in the video guides may dier slightly to
your chosen building. Please ensure to read your instructions carefully to avoid
error.

ACCESSING VIDEO GUIDES...

 

Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Overall Dimensions:
Width = 1596mm
Depth = 2138mm
Height = 2156mm
Base Dimensions:
Width = 1456mm
Depth = 2066mm
9
11
14
Fascia 12x60x847mm QTY 4
S1260-847mm
Inner Door Block 28x28x150mm QTY 1
FS2828-150mm
Cover Trims 12x40x1792mm QTY 7
S1240-1792mm
Ridge Bar 28x28x2010mm QTY 1
FS2828-2010mm
Finial QTY 2
Diamond Shed Finial
Door Panel QTY 1
AI-01S11SHSD1180X1802-V1
Gable Top QTY 2
AI-S11SHAGT1406X337-V1
Floor QTY 1
AI-R11MBF1456X2066-V1
Roof QTY 2
AI-S11MBOHAR866X2090-V1
1st Plain Panel QTY 1
AI-S11SHPPTF282X1802-V1
2nd Plain Panel QTY 2
AI-S11SHPPTF830X1802-V1
3rd Plain Panel QTY 2
AI-S11SHPPTF1180X1802-V1
4th Plain Panel QTY 1
AI-S11SHPPTF1462X1802-V1
Door QTY 1
AI-S11FBMBZBD743X1680-V1
8
1 2 3 4 5
67
Door Beading Strip 12x28x1590mm QTY 2
S1228-1590mm
T Hinge QTY 3
PI-02-1042
Felt
L-Bracket QTY 2
PI-07-0012
16
17
Turn Button QTY 2
PI-07-0034
18
19
20
12
13
15
Pad Bolt QTY 1
PI-07-0035
10
Nail Bag
There may be extra screws present in the nail bag
50mm Screw x 50
20mm Screw x 8
40mm Screw x 38
30mm Screw x 64
60mm Screw x 10
Felt Tacks x 66
This building can be built as an Apex or a Reverse Apex. You can also choose
in which arrangement you wish to have your panels set up. The below
images may give you an idea of which set up is most suitable for you.
Contents:

 

Pre Assembly
Before assembling remove the transportation
blocks from the bottom of each panel.
Take care removing the blocks as to not damage
the panels. Tap with a at headed screwdriver
and hammer.
Dispose of the blocks once removed.
PLEASE SCAN HERE:
17
Pre drill
hole
30mm
screw
1
6
Opens from the Left Opens from the Right
IMPORTANT: Pre-drill before xing screws.
Step 1
Parts needed - No. 1 QTY 1
No. 6 QTY 1
No. 17 QTY 3
Place the door (No. 6) within the Door
Panel (No. 1). Fix the T Hinges (No. 17)
onto the door and Door Panel as shown
(taking into account on which side of the
Door Panel opening you want the Door
to open).
Ensure that the screws go through the
cladding and into the framing behind.
21x30mm Screws
*PLEASE NOTE** Before tting the hinges,
ensure the door is in the correct position
depending on which side you want the
door to open. See external illustrations
below which show the doors internal
framing.
PLEASE SCAN HERE:

 

8
Step 2
Parts needed - No. 8 QTY 1
Place the oor panels (No. 8) onto a rm
and level base. Ensure the base has suitable
drainage, free from areas where standing
water can collect. See front page for base
requirements.
IMPORTANT: Pre-drill before xing screws.
IMPORTANT: Pre-drill before xing screws.
50mm
screw
Pre drill
hole
5
3
a
Step 3
Parts needed - No. 3, (or 1, or 4 QTY 1)
No. 5 QTY 1
**Please note: The side panels are all
interchangeable and can be positioned in a
variety of congurations. Decide which works
best before assembly. See Page 2 for suggested
options.**
Locate the 4th Plain Panel (No. 5) and a 2nd Plain
Panel (No. 3) (or panel of your choice) on top of the
Floor, ensuring there is equal spacing between the
oor and cladding on all sides.
Secure the panels together at the corner with
3x50mm screws as shown in the diagram.
Do not secure the building to the oor until the roof
has been tted.
3x50mm Screws
a
a
a
IMPORTANT: Pre-drill before xing screws.
50mm
screw
Pre drill
hole
3
4
a
a
a
a
a
a
a
Step 4
Parts needed - No. 3, (or 1, or 4 QTY 1)
No. 4, (or 1, or 3 QTY 1)
Locate the 3rd Plain Panel (No. 4) and a 2nd
Plain Panel (No. 3) (or panel of your choice)
on top of the Floor, ensuring there is equal
spacing between the oor and cladding on
all sides.
Secure the panels to the adjacent panel
with 3x50mm screws, as shown in the
diagram.
Do not secure the building to the oor until
the roof has been tted.
6x50mm Screws
IMPORTANT: Pre-drill before xing screws.
50mm
screw
Pre drill
hole
4
2
Step 5
Parts needed - No. 2 QTY 1
No. 4, (or 1 QTY 1)
Locate the 3rd Plain Panel (No. 4) (or panel
of your choice) and the 1st Plain Panel
(No.2) on top of the Floor, ensuring there is
equal spacing between the oor and
cladding on all sides.
The 1st Plain Panel (No. 2) can go either
side of the front of the building, depending
on preference.
Secure the panels together at the corner
and to the adjacent panel with 3x50mm
screws, as shown in the diagram.
Do not secure the building to the oor until
the roof has been tted.
6x50mm Screws a
a
a
a
a
a
a

 

IMPORTANT: Pre-drill before xing screws.
50mm
screw
Pre drill
hole
1
a
a
a
a
a
a
a
Step 6
Parts needed - No. 1, (or 4 QTY 1)
Locate the Door Panel (No. 1) (or panel of
your choice) on top of the Floor, ensuring
there is equal spacing between the oor
and cladding on all sides.
Secure the panel to the adjacent panels
with 3x50mm screws, as shown in the
diagram.
Do not secure the building to the oor until
the roof has been tted.
6x50mm Screws
IMPORTANT: Pre-drill before xing screws.
50mm
screw
Pre drill
hole
7
7
Step 7
Parts needed - No. 7 QTY 2
Place the Gable Tops (No. 7) centrally
over the end panels, ensuring that the
cladding slots together.
Fix the Gables to the panel below using
4x50mm screws per gable, ensure to
stagger the screws so they don’t collide.
8x50mm Screws
7
IMPORTANT: Pre-drill before xing screws.
20mm
screw
Pre drill
hole
18
14
Step 8
Parts needed - No. 14 QTY 1
No. 18 QTY 2
Place the ridge bar (No. 14) in between
the Gable Tops (No. 8) in line with the
central framing of the gable tops.
Fix the ridge bar to the gable using one
L bracket (No. 18) per end. Fix with
4x20mm screws each.
8x20mm Screws
bb

 

IMPORTANT: Pre-drill before xing screws.
60mm
screw
Pre drill
hole
9
9
Step 9
Parts needed - No. 9 QTY 2
Place the Roof Panels (No. 9) on top of the building
making sure the framing in the roof panels sits
rmly within the Gable Tops (No. 7) and on top of
the Ridge Bar (No. 14).
**Make sure that you have got the roof panels
the correct way round with the recess at the top
of the apex as shown in the diagram.**
**The edges of the roof panels must be ush
with the outer cladding of the Gable Tops
(No.7).**
From the top, x directly through the roof panels
(No. 9) and into the ridge bar (No. 14) below using
5x60mm screws per roof panel .
It is essential that the ridge bar (No. 14) and roof
panel (No. 9) framing pull together when xed
with 60mm screws. You may require another
person pushing the ridge bar (No. 14) up from
below to achieve this.
HINT - Follow the nailing line of the framing on the
roof panel so that you are more likely to x into the
ridge bar below.
10x60mm Screws
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
40mm
screw
Step 10
Use 40mm screws to secure the Roof (No. 9)
in place, ensuring there is no more than
300mm between each screw.
Make sure that the screws go through the
cladding into the framing below.
22x40mm Screws
IMPORTANT: Pre-drill before xing screws.
Step 11
Once the roof is xed, attach the building to
the oor with 50mm screws.
Ensure the screws go through the panel
into the oor framing
21x50mm Screws
50mm
screw
Pre drill
hole
b
b
bbb
b
b
b
b
b

 

Felt
tacks
20 20
Step 12
Parts needed - No. 20 QTY 1
Cut the felt (No. 20) into two sheets
measuring 2000mm (L) x 1000mm(W).
Lay the sheets onto roof as shown in
diagram, ensuring there is a 50mm
overhang around the sides.
Apply the felt tacks with a 100mm space
per tack.
66 x Felt Tacks
1.
2.
20 20
HANDLE
WITH CARE
12
3
4
100mm
IMPORTANT: Pre-drill before xing screws.
30mm
screw
Pre drill
hole
13
13
Step 13
Parts needed - No. 13 QTY 7
Fit the Cover Trims (No. 13) over each
panel join and corner of the building as
shown in the illustration using 30mm
screws.
21x30mm Screws
13
13
13
IMPORTANT: Pre-drill before xing screws.
40mm
screw
Pre drill
hole
11
11
16
Step 14
Parts needed - No. 11 QTY 4
No. 16 QTY 2
Fit the Fascias (No. 11) to the roof
over the felt and secure in place
with 40mm screws as shown.
Followed by adding the Finials
(No. 16) over the Fascias using
2x40mm screws per Finial.
16x40mm Screws
16
11
11

 

IMPORTANT: Pre-drill before xing screws.
Use 4x30mm Screws to x each Door
Beading Strips (No. 12) onto the
insides of the Door Panel (No. 1)
opening. Ensure that the screw is
parallel with the door frame when
xing the strip to the Door Panel as
shown in the close up view.
Attach the Inner Door Block (No. 10)
to the door (No. 6) using 2x30mm
screws, in the positions illustrated.
Screw through the door cladding into
the blocks using 30mm screws
10x30mm Screws
Step 15
Parts needed - No. 10 QTY 1
No. 12 QTY 2
30mm
screw
Pre drill
hole
12
12
a
b
a
b
10
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
30mm
screw
19
Step 16
Parts needed - No. 19 QTY 1
Screw the Pad Bolt (No. 19) on to the door
(No. 6) and the retainer to the door panel
(No. 1) using 10x30mm screws. Make sure
that you screw into the framing behind.
10x30mm Screws.
IMPORTANT: Pre-drill before xing screws.
15
30mm
screw
Pre drill
hole
Step 17
Parts needed - No. 15 QTY 2
Fix the Turn Button (No. 15) onto the
Door Panel (No. 1) using 1x30mm
screw for each one.
*These turn buttons help to keep
your doors straight during high and
low levels of moisture content in
the air.*
2x30mm Screws